|
|
|
|
@ -403,50 +403,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
|
|
|
|
|
//============================= Z Probe Options =============================
|
|
|
|
|
//===========================================================================
|
|
|
|
|
|
|
|
|
|
// Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine.
|
|
|
|
|
// With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing.
|
|
|
|
|
//
|
|
|
|
|
// *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! ***
|
|
|
|
|
//
|
|
|
|
|
// To continue using the Z-min-endstop for homing, be sure to disable Z_SAFE_HOMING.
|
|
|
|
|
// Example: To park the head outside the bed area when homing with G28.
|
|
|
|
|
//
|
|
|
|
|
// To use a separate Z probe, your board must define a Z_MIN_PROBE_PIN.
|
|
|
|
|
//
|
|
|
|
|
// For a servo-based Z probe, you must set up servo support below, including
|
|
|
|
|
// NUM_SERVOS, Z_ENDSTOP_SERVO_NR and Z_SERVO_ANGLES.
|
|
|
|
|
//
|
|
|
|
|
// - RAMPS 1.3/1.4 boards may be able to use the 5V, GND, and Aux4->D32 pin.
|
|
|
|
|
// - Use 5V for powered (usu. inductive) sensors.
|
|
|
|
|
// - Otherwise connect:
|
|
|
|
|
// - normally-closed switches to GND and D32.
|
|
|
|
|
// - normally-open switches to 5V and D32.
|
|
|
|
|
//
|
|
|
|
|
// Normally-closed switches are advised and are the default.
|
|
|
|
|
//
|
|
|
|
|
// The Z_MIN_PROBE_PIN sets the Arduino pin to use. (See your board's pins file.)
|
|
|
|
|
// Since the RAMPS Aux4->D32 pin maps directly to the Arduino D32 pin, D32 is the
|
|
|
|
|
// default pin for all RAMPS-based boards. Some other boards map differently.
|
|
|
|
|
// To set or change the pin for your board, edit the appropriate pins_XXXXX.h file.
|
|
|
|
|
//
|
|
|
|
|
// WARNING:
|
|
|
|
|
// Setting the wrong pin may have unexpected and potentially disastrous consequences.
|
|
|
|
|
// Use with caution and do your homework.
|
|
|
|
|
//
|
|
|
|
|
//#define Z_MIN_PROBE_ENDSTOP
|
|
|
|
|
|
|
|
|
|
// Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE.
|
|
|
|
|
// The Z_MIN_PIN will then be used for both Z-homing and probing.
|
|
|
|
|
#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
|
|
|
|
|
|
|
|
|
|
// To use a probe you must enable one of the two options above!
|
|
|
|
|
|
|
|
|
|
// This option disables the use of the Z_MIN_PROBE_PIN
|
|
|
|
|
// To enable the Z probe pin but disable its use, uncomment the line below. This only affects a
|
|
|
|
|
// Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above.
|
|
|
|
|
// If you're using the Z MIN endstop connector for your Z probe, this has no effect.
|
|
|
|
|
//#define DISABLE_Z_MIN_PROBE_ENDSTOP
|
|
|
|
|
|
|
|
|
|
//
|
|
|
|
|
// Probe Type
|
|
|
|
|
// Probes are sensors/switches that are activated / deactivated before/after use.
|
|
|
|
|
@ -498,6 +454,50 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
|
|
|
|
|
// Allen Key Probe is defined in the Delta example configurations.
|
|
|
|
|
//
|
|
|
|
|
|
|
|
|
|
// Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine.
|
|
|
|
|
// With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing.
|
|
|
|
|
//
|
|
|
|
|
// *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! ***
|
|
|
|
|
//
|
|
|
|
|
// To continue using the Z-min-endstop for homing, be sure to disable Z_SAFE_HOMING.
|
|
|
|
|
// Example: To park the head outside the bed area when homing with G28.
|
|
|
|
|
//
|
|
|
|
|
// To use a separate Z probe, your board must define a Z_MIN_PROBE_PIN.
|
|
|
|
|
//
|
|
|
|
|
// For a servo-based Z probe, you must set up servo support below, including
|
|
|
|
|
// NUM_SERVOS, Z_ENDSTOP_SERVO_NR and Z_SERVO_ANGLES.
|
|
|
|
|
//
|
|
|
|
|
// - RAMPS 1.3/1.4 boards may be able to use the 5V, GND, and Aux4->D32 pin.
|
|
|
|
|
// - Use 5V for powered (usu. inductive) sensors.
|
|
|
|
|
// - Otherwise connect:
|
|
|
|
|
// - normally-closed switches to GND and D32.
|
|
|
|
|
// - normally-open switches to 5V and D32.
|
|
|
|
|
//
|
|
|
|
|
// Normally-closed switches are advised and are the default.
|
|
|
|
|
//
|
|
|
|
|
// The Z_MIN_PROBE_PIN sets the Arduino pin to use. (See your board's pins file.)
|
|
|
|
|
// Since the RAMPS Aux4->D32 pin maps directly to the Arduino D32 pin, D32 is the
|
|
|
|
|
// default pin for all RAMPS-based boards. Some other boards map differently.
|
|
|
|
|
// To set or change the pin for your board, edit the appropriate pins_XXXXX.h file.
|
|
|
|
|
//
|
|
|
|
|
// WARNING:
|
|
|
|
|
// Setting the wrong pin may have unexpected and potentially disastrous consequences.
|
|
|
|
|
// Use with caution and do your homework.
|
|
|
|
|
//
|
|
|
|
|
//#define Z_MIN_PROBE_ENDSTOP
|
|
|
|
|
|
|
|
|
|
// Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE.
|
|
|
|
|
// The Z_MIN_PIN will then be used for both Z-homing and probing.
|
|
|
|
|
#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
|
|
|
|
|
|
|
|
|
|
// To use a probe you must enable one of the two options above!
|
|
|
|
|
|
|
|
|
|
// This option disables the use of the Z_MIN_PROBE_PIN
|
|
|
|
|
// To enable the Z probe pin but disable its use, uncomment the line below. This only affects a
|
|
|
|
|
// Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above.
|
|
|
|
|
// If you're using the Z MIN endstop connector for your Z probe, this has no effect.
|
|
|
|
|
//#define DISABLE_Z_MIN_PROBE_ENDSTOP
|
|
|
|
|
|
|
|
|
|
// Enable Z Probe Repeatability test to see how accurate your probe is
|
|
|
|
|
//#define Z_MIN_PROBE_REPEATABILITY_TEST
|
|
|
|
|
|
|
|
|
|
@ -512,8 +512,8 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
|
|
|
|
|
//
|
|
|
|
|
// For M851 give a range for adjusting the Z probe offset
|
|
|
|
|
//
|
|
|
|
|
#define Z_PROBE_OFFSET_RANGE_MIN -20
|
|
|
|
|
#define Z_PROBE_OFFSET_RANGE_MAX 20
|
|
|
|
|
#define Z_PROBE_OFFSET_RANGE_MIN -5
|
|
|
|
|
#define Z_PROBE_OFFSET_RANGE_MAX 0
|
|
|
|
|
|
|
|
|
|
// For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
|
|
|
|
|
// :{0:'Low',1:'High'}
|
|
|
|
|
@ -733,11 +733,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
|
|
|
|
|
//============================= Additional Features ===========================
|
|
|
|
|
//=============================================================================
|
|
|
|
|
|
|
|
|
|
// @section probes
|
|
|
|
|
|
|
|
|
|
#define Z_PROBE_OFFSET_RANGE_MIN -5
|
|
|
|
|
#define Z_PROBE_OFFSET_RANGE_MAX 0
|
|
|
|
|
|
|
|
|
|
// @section extras
|
|
|
|
|
|
|
|
|
|
//
|
|
|
|
|
@ -977,8 +972,10 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
|
|
|
|
|
//
|
|
|
|
|
//#define ULTIPANEL
|
|
|
|
|
|
|
|
|
|
//
|
|
|
|
|
// Cartesio UI
|
|
|
|
|
// http://mauk.cc/webshop/cartesio-shop/electronics/user-interface
|
|
|
|
|
//
|
|
|
|
|
//#define CARTESIO_UI
|
|
|
|
|
|
|
|
|
|
//
|
|
|
|
|
@ -1103,7 +1100,9 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
|
|
|
|
|
//
|
|
|
|
|
//#define U8GLIB_SSD1306
|
|
|
|
|
|
|
|
|
|
//
|
|
|
|
|
// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules
|
|
|
|
|
//
|
|
|
|
|
//#define SAV_3DGLCD
|
|
|
|
|
#if ENABLED(SAV_3DGLCD)
|
|
|
|
|
//#define U8GLIB_SSD1306
|
|
|
|
|
|
Scott Lahteine
9 years ago
committed by