removed unused HEATING_EARLY_FINISH_DEG_OFFSET

Simplified stepper inactive time

Marlin/Configuration_adv.h

@@ -25,9 +25,6 @@
 // if CooldownNoWait is defined M109 will not wait for the cooldown to finish
 #define CooldownNoWait true
 
-// Heating is finished if a temperature close to this degree shift is reached
-#define HEATING_EARLY_FINISH_DEG_OFFSET 1 //Degree
-
 //Do not wait for M109 to finish when printing from SD card
 //#define STOP_HEATING_WAIT_WHEN_SD_PRINTING
 
@@ -85,7 +82,6 @@
 
 //default stepper release if idle
 #define DEFAULT_STEPPER_DEACTIVE_TIME 60
-#define DEFAULT_STEPPER_DEACTIVE_COMMAND "M84 X Y E"  //z stays  powered
 
 #define DEFAULT_MINIMUMFEEDRATE       0.0     // minimum feedrate
 #define DEFAULT_MINTRAVELFEEDRATE     0.0
@@ -112,7 +108,7 @@
 
 
 #define SD_FINISHED_STEPPERRELEASE true  //if sd support and the file is finished: disable steppers?
-#define SD_FINISHED_RELEASECOMMAND "M84 X Y E" // no z because of layer shift.
+#define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // no z because of layer shift.
 
 // The hardware watchdog should halt the Microcontroller, in case the firmware gets stuck somewhere. However:
 // the Watchdog is not working well, so please only enable this for testing

Marlin/Marlin.pde

@@ -165,7 +165,6 @@ const int sensitive_pins[] = SENSITIVE_PINS; // Sensitive pin list for M42
 static unsigned long previous_millis_cmd = 0;
 static unsigned long max_inactive_time = 0;
 static unsigned long stepper_inactive_time = DEFAULT_STEPPER_DEACTIVE_TIME*1000l;
-static unsigned long last_stepperdisabled_time=30*1000; //first release check after 30 seconds
 
 static unsigned long starttime=0;
 static unsigned long stoptime=0;
@@ -1296,16 +1295,15 @@ void manage_inactivity(byte debug)
   if( (millis() - previous_millis_cmd) >  max_inactive_time ) 
     if(max_inactive_time) 
       kill(); 
-  if(stepper_inactive_time)  
+  if(stepper_inactive_time)  {
-  if( (millis() - last_stepperdisabled_time) >  stepper_inactive_time ) 
+    if( (millis() - previous_millis_cmd) >  stepper_inactive_time ) 
     {
-    if(previous_millis_cmd>last_stepperdisabled_time)
+      disable_x();
-      last_stepperdisabled_time=previous_millis_cmd;
+      disable_y();
-    else
+      disable_z();
-    {
+      disable_e0();
-      if(  (X_ENABLE_ON && (READ(X_ENABLE_PIN)!=0))  ||  (!X_ENABLE_ON && READ(X_ENABLE_PIN)==0)  )
+      disable_e1();
-        enquecommand(DEFAULT_STEPPER_DEACTIVE_COMMAND); 
+      disable_e2();
-      last_stepperdisabled_time=millis();
     }
   }
   #ifdef EXTRUDER_RUNOUT_PREVENT
@@ -1323,7 +1321,6 @@ void manage_inactivity(byte debug)
      destination[E_AXIS]=oldedes;
      plan_set_e_position(oldepos);
      previous_millis_cmd=millis();
-     //enquecommand(DEFAULT_STEPPER_DEACTIVE_COMMAND);
      st_synchronize();
      WRITE(E0_ENABLE_PIN,oldstatus);
     }