Added #ifdef BARICUDA around the BariCUDA changes

Marlin/Configuration.h

@@ -403,6 +403,9 @@ const bool Z_ENDSTOPS_INVERTING = true; // set to true to invert the logic of th
 // SF send wrong arc g-codes when using Arc Point as fillet procedure
 //#define SF_ARC_FIX
 
+// Support for the BariCUDA Paste Extruder.
+//#define BARICUDA
+
 #include "Configuration_adv.h"
 #include "thermistortables.h"
 

Marlin/Marlin.h

@@ -186,8 +186,10 @@ extern float add_homeing[3];
 extern float min_pos[3];
 extern float max_pos[3];
 extern int fanSpeed;
+#ifdef BARICUDA
 extern int ValvePressure;
 extern int EtoPPressure;
+#endif
 
 #ifdef FWRETRACT
 extern bool autoretract_enabled;

Marlin/Marlin_main.cpp

@@ -172,8 +172,10 @@ float extruder_offset[2][EXTRUDERS] = {
 #endif
 uint8_t active_extruder = 0;
 int fanSpeed=0;
+#ifdef BARICUDA
 int ValvePressure=0;
 int EtoPPressure=0;
+#endif
 
 #ifdef FWRETRACT
   bool autoretract_enabled=true;
@@ -1174,7 +1176,7 @@ void process_commands()
         fanSpeed = 0;
         break;
     #endif //FAN_PIN
-
+    #ifdef BARICUDA
 	// PWM for HEATER_1_PIN
       #if HEATER_1_PIN > -1
         case 126: //M126 valve open
@@ -1204,7 +1206,7 @@ void process_commands()
           EtoPPressure = 0;
           break;
       #endif //HEATER_2_PIN
-
+    #endif
 
     #if (PS_ON_PIN > -1)
       case 80: // M80 - ATX Power On

Marlin/pins.h

@@ -1474,7 +1474,11 @@
 #define HEATER_1_PIN 7
 #define TEMP_1_PIN 1
 
+#ifdef BARICUDA
 #define HEATER_2_PIN 6
+#else
+#define HEATER_2_PIN -1
+#endif
 #define TEMP_2_PIN -1
 
 #define E0_STEP_PIN         34

Marlin/planner.cpp

@@ -439,18 +439,22 @@ void check_axes_activity()
   unsigned char z_active = 0;
   unsigned char e_active = 0;
   unsigned char tail_fan_speed = fanSpeed;
+  #ifdef BARICUDA
   unsigned char valve_pressure = 0;
   unsigned char e_to_p_pressure = 0;
   unsigned char tail_valve_pressure = 0;
   unsigned char tail_e_to_p_pressure = 0;
+  #endif
   block_t *block;
 
   if(block_buffer_tail != block_buffer_head)
   {
     uint8_t block_index = block_buffer_tail;
     tail_fan_speed = block_buffer[block_index].fan_speed;
+    #ifdef BARICUDA
     tail_valve_pressure = block_buffer[block_index].valve_pressure;
     tail_e_to_p_pressure = block_buffer[block_index].e_to_p_pressure;
+    #endif
     while(block_index != block_buffer_head)
     {
       block = &block_buffer[block_index];
@@ -493,6 +497,7 @@ void check_axes_activity()
   getHighESpeed();
 #endif
 
+#ifdef BARICUDA
   #if HEATER_1_PIN > -1
     if (ValvePressure != 0){
       analogWrite(HEATER_1_PIN,ValvePressure); // If buffer is empty use current valve pressure
@@ -520,6 +525,7 @@ void check_axes_activity()
       analogWrite(HEATER_2_PIN,tail_e_to_p_pressure);
     }
   #endif
+#endif
 }
 
 
@@ -593,8 +599,10 @@ void plan_buffer_line(const float &x, const float &y, const float &z, const floa
   }
 
   block->fan_speed = fanSpeed;
+  #ifdef BARICUDA
   block->valve_pressure = ValvePressure;
   block->e_to_p_pressure = EtoPPressure;
+  #endif
 
   // Compute direction bits for this block 
   block->direction_bits = 0;

Marlin/planner.h

@@ -60,8 +60,10 @@ typedef struct {
   unsigned long final_rate;                          // The minimal rate at exit
   unsigned long acceleration_st;                     // acceleration steps/sec^2
   unsigned long fan_speed;
+  #ifdef BARICUDA
   unsigned long valve_pressure;
   unsigned long e_to_p_pressure;
+  #endif
   volatile char busy;
 } block_t;