Merge pull request #3107 from AnHardt/z_raise_before_homing

Z_RAISE_BEFORE_HOMING -> MIN_Z_HEIGHT_FOR_HOMING

Marlin/Configuration.h

@@ -378,6 +378,8 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 #define INVERT_E3_DIR false
 
 // @section homing
+//#define MIN_Z_HEIGHT_FOR_HOMING 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
+                                    // Be sure you have this distance over your Z_MAX_POS in case.
 
 // ENDSTOP SETTINGS:
 // Sets direction of endstops when homing; 1=MAX, -1=MIN
@@ -509,9 +511,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
   #define Y_PROBE_OFFSET_FROM_EXTRUDER 10  // Z offset: -front [of the nozzle] +behind
   #define Z_PROBE_OFFSET_FROM_EXTRUDER 0   // Z offset: -below [the nozzle] (always negative!)
 
-  #define Z_RAISE_BEFORE_HOMING 4       // (in mm) Raise Z axis before homing (G28) for Z probe clearance.
-                                        // Be sure you have this distance over your Z_MAX_POS in case.
-
   #define XY_TRAVEL_SPEED 8000         // X and Y axis travel speed between probes, in mm/min.
 
   #define Z_RAISE_BEFORE_PROBING 15   // How much the Z axis will be raised before traveling to the first probing point.

Marlin/Marlin_main.cpp

@@ -2268,7 +2268,7 @@ inline void gcode_G28() {
 
   setup_for_endstop_move();
 
-  set_destination_to_current();
+  set_destination_to_current(); // Directly after a reset this is all 0. Later we get a hint if we have to raise z or not.
 
   feedrate = 0.0;
 
@@ -2311,50 +2311,40 @@ inline void gcode_G28() {
 
     home_all_axis = (!homeX && !homeY && !homeZ) || (homeX && homeY && homeZ);
 
-    if (home_all_axis || homeZ) {
+    #if Z_HOME_DIR > 0  // If homing away from BED do Z first
-
-      #if Z_HOME_DIR > 0  // If homing away from BED do Z first
 
+      if (home_all_axis || homeZ) {
         HOMEAXIS(Z);
         #if ENABLED(DEBUG_LEVELING_FEATURE)
           if (marlin_debug_flags & DEBUG_LEVELING) {
             print_xyz("> HOMEAXIS(Z) > current_position", current_position);
           }
         #endif
+      }
 
-      #elif defined(Z_RAISE_BEFORE_HOMING) && Z_RAISE_BEFORE_HOMING > 0
+    #elif defined(MIN_Z_HEIGHT_FOR_HOMING) && MIN_Z_HEIGHT_FOR_HOMING > 0
-
-        // Consider the current Z-position as zero
-        // !!WARNING!! If the machine has no physical z-max endstops then we
-        // can move the axis more than it can physically travel.
-        current_position[Z_AXIS] = 0;
-        sync_plan_position();
-
-        // (Does this need to be "negative home direction?" Why not just use Z_RAISE_BEFORE_HOMING?)
-        destination[Z_AXIS] = -Z_RAISE_BEFORE_HOMING * home_dir(Z_AXIS);
-        feedrate = max_feedrate[Z_AXIS] * 60;
 
+      // Raise Z before homing any other axes and z is not already high enough (never lower z)
+      if (current_position[Z_AXIS] <= MIN_Z_HEIGHT_FOR_HOMING) {
+        destination[Z_AXIS] = MIN_Z_HEIGHT_FOR_HOMING;
+        feedrate = max_feedrate[Z_AXIS] * 60;  // feedrate (mm/m) = max_feedrate (mm/s)
         #if ENABLED(DEBUG_LEVELING_FEATURE)
           if (marlin_debug_flags & DEBUG_LEVELING) {
-            SERIAL_ECHOPAIR("Raise Z (before homing) by ", (float)Z_RAISE_BEFORE_HOMING);
+            SERIAL_ECHOPAIR("Raise Z (before homing) to ", (float)MIN_Z_HEIGHT_FOR_HOMING);
             SERIAL_EOL;
             print_xyz("> (home_all_axis || homeZ) > current_position", current_position);
             print_xyz("> (home_all_axis || homeZ) > destination", destination);
           }
         #endif
-
-        // Raise Z-axis by Z_RAISE_BEFORE_HOMING before homing any other axis
         line_to_destination();
         st_synchronize();
 
         // Update the current Z position even if it currently not real from Z-home
         // otherwise each call to line_to_destination() will want to move Z-axis
-        // by Z_RAISE_BEFORE_HOMING.
+        // by MIN_Z_HEIGHT_FOR_HOMING.
         current_position[Z_AXIS] = destination[Z_AXIS];
-
+      }
-      #endif
+    #endif
-
-    } // home_all_axis || homeZ
 
     #if ENABLED(QUICK_HOME)
 
@@ -2468,19 +2458,18 @@ inline void gcode_G28() {
 
           if (home_all_axis) {
 
-            // At this point we already have Z at Z_RAISE_BEFORE_HOMING height
+            // At this point we already have Z at MIN_Z_HEIGHT_FOR_HOMING height
             // No need to move Z any more as this height should already be safe
-            // enough to reach Z_SAFE_HOMING XY positions; just make sure the
+            // enough to reach Z_SAFE_HOMING XY positions.
-            // planner is in sync.
+            // Just make sure the planner is in sync.
             sync_plan_position();
 
             //
             // Set the Z probe (or just the nozzle) destination to the safe homing point
             //
-            // NOTE: If current_position[X_AXIS] or current_position[Y_AXIS] were set above
-            // then this may not work as expected.
             destination[X_AXIS] = round(Z_SAFE_HOMING_X_POINT - X_PROBE_OFFSET_FROM_EXTRUDER);
             destination[Y_AXIS] = round(Z_SAFE_HOMING_Y_POINT - Y_PROBE_OFFSET_FROM_EXTRUDER);
+            destination[Z_AXIS] = current_position[Z_AXIS]; //z is already at the right height
             feedrate = XY_TRAVEL_SPEED;
 
             #if ENABLED(DEBUG_LEVELING_FEATURE)
@@ -2494,8 +2483,8 @@ inline void gcode_G28() {
             line_to_destination();
             st_synchronize();
 
-            // Update the current positions for XY, Z is still at
+            // Update the current positions for XY, Z is still at least at
-            // Z_RAISE_BEFORE_HOMING height, no changes there.
+            // MIN_Z_HEIGHT_FOR_HOMING height, no changes there.
             current_position[X_AXIS] = destination[X_AXIS];
             current_position[Y_AXIS] = destination[Y_AXIS];
 
@@ -2515,26 +2504,6 @@ inline void gcode_G28() {
                   && cpx <= X_MAX_POS - X_PROBE_OFFSET_FROM_EXTRUDER
                   && cpy >= Y_MIN_POS - Y_PROBE_OFFSET_FROM_EXTRUDER
                   && cpy <= Y_MAX_POS - Y_PROBE_OFFSET_FROM_EXTRUDER) {
-                // Set the plan current position to X, Y, 0
-                current_position[Z_AXIS] = 0;
-                plan_set_position(cpx, cpy, 0, current_position[E_AXIS]); // = sync_plan_position
-
-                // Set Z destination away from bed and raise the axis
-                // NOTE: This should always just be Z_RAISE_BEFORE_HOMING unless...???
-                destination[Z_AXIS] = -Z_RAISE_BEFORE_HOMING * home_dir(Z_AXIS);
-                feedrate = max_feedrate[Z_AXIS] * 60;  // feedrate (mm/m) = max_feedrate (mm/s)
-
-                #if ENABLED(DEBUG_LEVELING_FEATURE)
-                  if (marlin_debug_flags & DEBUG_LEVELING) {
-                    SERIAL_ECHOPAIR("Raise Z (before homing) by ", (float)Z_RAISE_BEFORE_HOMING);
-                    SERIAL_EOL;
-                    print_xyz("> homeZ > current_position", current_position);
-                    print_xyz("> homeZ > destination", destination);
-                  }
-                #endif
-
-                line_to_destination();
-                st_synchronize();
 
                 // Home the Z axis
                 HOMEAXIS(Z);

Marlin/SanityCheck.h

@@ -368,6 +368,8 @@
   #error SDSLOW deprecated - set SPI_SPEED to SPI_HALF_SPEED instead
 #elif defined(SDEXTRASLOW)
   #error SDEXTRASLOW deprecated - set SPI_SPEED to SPI_QUARTER_SPEED instead
+#elif defined(Z_RAISE_BEFORE_HOMING)
+  #error Z_RAISE_BEFORE_HOMING is deprecated. Use MIN_Z_HEIGHT_FOR_HOMING instead.
 #endif
 
 #endif //SANITYCHECK_H

Marlin/example_configurations/Felix/Configuration.h

@@ -360,6 +360,8 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 #define INVERT_E3_DIR false
 
 // @section homing
+//#define MIN_Z_HEIGHT_FOR_HOMING 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
+                                    // Be sure you have this distance over your Z_MAX_POS in case.
 
 // ENDSTOP SETTINGS:
 // Sets direction of endstops when homing; 1=MAX, -1=MIN
@@ -491,9 +493,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
   #define Y_PROBE_OFFSET_FROM_EXTRUDER -29     // Z offset: -front [of the nozzle] +behind
   #define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35  // Z offset: -below [the nozzle] (always negative!)
 
-  #define Z_RAISE_BEFORE_HOMING 4       // (in mm) Raise Z axis before homing (G28) for Z probe clearance.
-                                        // Be sure you have this distance over your Z_MAX_POS in case.
-
   #define XY_TRAVEL_SPEED 8000         // X and Y axis travel speed between probes, in mm/min.
 
   #define Z_RAISE_BEFORE_PROBING 15   // How much the Z axis will be raised before traveling to the first probing point.

Marlin/example_configurations/Felix/Configuration_DUAL.h

@@ -357,6 +357,8 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 #define INVERT_E3_DIR false
 
 // @section homing
+//#define MIN_Z_HEIGHT_FOR_HOMING 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
+                                    // Be sure you have this distance over your Z_MAX_POS in case.
 
 // ENDSTOP SETTINGS:
 // Sets direction of endstops when homing; 1=MAX, -1=MIN
@@ -488,9 +490,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
   #define Y_PROBE_OFFSET_FROM_EXTRUDER -29     // Z offset: -front [of the nozzle] +behind
   #define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35  // Z offset: -below [the nozzle] (always negative!)
 
-  #define Z_RAISE_BEFORE_HOMING 4       // (in mm) Raise Z axis before homing (G28) for Z probe clearance.
-                                        // Be sure you have this distance over your Z_MAX_POS in case.
-
   #define XY_TRAVEL_SPEED 8000         // X and Y axis travel speed between probes, in mm/min.
 
   #define Z_RAISE_BEFORE_PROBING 15   // How much the Z axis will be raised before traveling to the first probing point.

Marlin/example_configurations/Hephestos/Configuration.h

@@ -370,6 +370,8 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
 #define INVERT_E3_DIR false
 
 // @section homing
+//#define MIN_Z_HEIGHT_FOR_HOMING 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
+                                    // Be sure you have this distance over your Z_MAX_POS in case.
 
 // ENDSTOP SETTINGS:
 // Sets direction of endstops when homing; 1=MAX, -1=MIN
@@ -501,9 +503,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
   #define Y_PROBE_OFFSET_FROM_EXTRUDER -29     // Z offset: -front [of the nozzle] +behind
   #define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35  // Z offset: -below [the nozzle] (always negative!)
 
-  #define Z_RAISE_BEFORE_HOMING 4       // (in mm) Raise Z axis before homing (G28) for Z probe clearance.
-                                        // Be sure you have this distance over your Z_MAX_POS in case.
-
   #define XY_TRAVEL_SPEED 8000         // X and Y axis travel speed between probes, in mm/min.
 
   #define Z_RAISE_BEFORE_PROBING 15   // How much the Z axis will be raised before traveling to the first probing point.

Marlin/example_configurations/Hephestos_2/Configuration.h

@@ -373,6 +373,8 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 #define INVERT_E3_DIR false
 
 // @section homing
+//#define MIN_Z_HEIGHT_FOR_HOMING 5 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
+                                    // Be sure you have this distance over your Z_MAX_POS in case.
 
 // ENDSTOP SETTINGS:
 // Sets direction of endstops when homing; 1=MAX, -1=MIN
@@ -504,9 +506,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
   #define Y_PROBE_OFFSET_FROM_EXTRUDER 15  // Z probe to nozzle Y offset: -front +behind
   #define Z_PROBE_OFFSET_FROM_EXTRUDER 0   // Z probe to nozzle Z offset: -below (always!)
 
-  #define Z_RAISE_BEFORE_HOMING 5       // (in mm) Raise Z axis before homing (G28) for Z probe clearance.
-                                        // Be sure you have this distance over your Z_MAX_POS in case.
-
   #define XY_TRAVEL_SPEED 8000         // X and Y axis travel speed between probes, in mm/min.
 
   #define Z_RAISE_BEFORE_PROBING 5    // How much the Z axis will be raised before traveling to the first probing point.

Marlin/example_configurations/K8200/Configuration.h

@@ -393,6 +393,8 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 #define INVERT_E3_DIR true
 
 // @section homing
+//#define MIN_Z_HEIGHT_FOR_HOMING 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
+                                    // Be sure you have this distance over your Z_MAX_POS in case.
 
 // ENDSTOP SETTINGS:
 // Sets direction of endstops when homing; 1=MAX, -1=MIN
@@ -524,9 +526,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
   #define Y_PROBE_OFFSET_FROM_EXTRUDER -29     // Z offset: -front [of the nozzle] +behind
   #define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35  // Z offset: -below [the nozzle] (always negative!)
 
-  #define Z_RAISE_BEFORE_HOMING 4       // (in mm) Raise Z axis before homing (G28) for Z probe clearance.
-                                        // Be sure you have this distance over your Z_MAX_POS in case.
-
   #define XY_TRAVEL_SPEED 8000         // X and Y axis travel speed between probes, in mm/min.
 
   #define Z_RAISE_BEFORE_PROBING 15   // How much the Z axis will be raised before traveling to the first probing point.

Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h

@@ -378,6 +378,8 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 #define INVERT_E3_DIR false
 
 // @section homing
+//#define MIN_Z_HEIGHT_FOR_HOMING 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
+                                    // Be sure you have this distance over your Z_MAX_POS in case.
 
 // ENDSTOP SETTINGS:
 // Sets direction of endstops when homing; 1=MAX, -1=MIN
@@ -509,9 +511,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
   #define Y_PROBE_OFFSET_FROM_EXTRUDER -29     // Z offset: -front [of the nozzle] +behind
   #define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35  // Z offset: -below [the nozzle] (always negative!)
 
-  #define Z_RAISE_BEFORE_HOMING 4       // (in mm) Raise Z axis before homing (G28) for Z probe clearance.
-                                        // Be sure you have this distance over your Z_MAX_POS in case.
-
   #define XY_TRAVEL_SPEED 8000         // X and Y axis travel speed between probes, in mm/min.
 
   #define Z_RAISE_BEFORE_PROBING 15   // How much the Z axis will be raised before traveling to the first probing point.

Marlin/example_configurations/RigidBot/Configuration.h

@@ -372,6 +372,8 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 #define INVERT_E3_DIR false
 
 // @section homing
+//#define MIN_Z_HEIGHT_FOR_HOMING 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
+                                    // Be sure you have this distance over your Z_MAX_POS in case.
 
 // ENDSTOP SETTINGS:
 // Sets direction of endstops when homing; 1=MAX, -1=MIN
@@ -503,9 +505,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
   #define Y_PROBE_OFFSET_FROM_EXTRUDER -29     // Z offset: -front [of the nozzle] +behind
   #define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35  // Z offset: -below [the nozzle] (always negative!)
 
-  #define Z_RAISE_BEFORE_HOMING 4       // (in mm) Raise Z axis before homing (G28) for Z probe clearance.
-                                        // Be sure you have this distance over your Z_MAX_POS in case.
-
   #define XY_TRAVEL_SPEED 8000         // X and Y axis travel speed between probes, in mm/min.
 
   #define Z_RAISE_BEFORE_PROBING 15   // How much the Z axis will be raised before traveling to the first probing point.

Marlin/example_configurations/SCARA/Configuration.h

@@ -386,6 +386,8 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 #define INVERT_E3_DIR false
 
 // @section homing
+//#define MIN_Z_HEIGHT_FOR_HOMING 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
+                                      // Be sure you have this distance over your Z_MAX_POS in case.
 
 // ENDSTOP SETTINGS:
 // Sets direction of endstops when homing; 1=MAX, -1=MIN
@@ -517,9 +519,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
   #define Y_PROBE_OFFSET_FROM_EXTRUDER -29     // Z offset: -front [of the nozzle] +behind
   #define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35  // Z offset: -below [the nozzle] (always negative!)
 
-  //#define Z_RAISE_BEFORE_HOMING 4       // (in mm) Raise Z axis before homing (G28) for Z probe clearance.
-                                        // Be sure you have this distance over your Z_MAX_POS in case.
-
   #define XY_TRAVEL_SPEED 8000         // X and Y axis travel speed between probes, in mm/min.
 
   #define Z_RAISE_BEFORE_PROBING 15   // How much the Z axis will be raised before traveling to the first probing point.

Marlin/example_configurations/TAZ4/Configuration.h

@@ -398,6 +398,8 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 #define INVERT_E3_DIR true
 
 // @section homing
+//#define MIN_Z_HEIGHT_FOR_HOMING 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
+                                    // Be sure you have this distance over your Z_MAX_POS in case.
 
 // ENDSTOP SETTINGS:
 // Sets direction of endstops when homing; 1=MAX, -1=MIN
@@ -529,9 +531,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
   #define Y_PROBE_OFFSET_FROM_EXTRUDER -29     // Z offset: -front [of the nozzle] +behind
   #define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35  // Z offset: -below [the nozzle] (always negative!)
 
-  #define Z_RAISE_BEFORE_HOMING 4       // (in mm) Raise Z axis before homing (G28) for Z probe clearance.
-                                        // Be sure you have this distance over your Z_MAX_POS in case.
-
   #define XY_TRAVEL_SPEED 8000         // X and Y axis travel speed between probes, in mm/min.
 
   #define Z_RAISE_BEFORE_PROBING 15   // How much the Z axis will be raised before traveling to the first probing point.

Marlin/example_configurations/WITBOX/Configuration.h

@@ -370,6 +370,8 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
 #define INVERT_E3_DIR false
 
 // @section homing
+//#define MIN_Z_HEIGHT_FOR_HOMING 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
+                                    // Be sure you have this distance over your Z_MAX_POS in case.
 
 // ENDSTOP SETTINGS:
 // Sets direction of endstops when homing; 1=MAX, -1=MIN
@@ -501,9 +503,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
   #define Y_PROBE_OFFSET_FROM_EXTRUDER -29     // Z offset: -front [of the nozzle] +behind
   #define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35  // Z offset: -below [the nozzle] (always negative!)
 
-  #define Z_RAISE_BEFORE_HOMING 4       // (in mm) Raise Z axis before homing (G28) for Z probe clearance.
-                                        // Be sure you have this distance over your Z_MAX_POS in case.
-
   #define XY_TRAVEL_SPEED 8000         // X and Y axis travel speed between probes, in mm/min.
 
   #define Z_RAISE_BEFORE_PROBING 15   // How much the Z axis will be raised before traveling to the first probing point.

Marlin/example_configurations/adafruit/ST7565/Configuration.h

@@ -378,6 +378,8 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 #define INVERT_E3_DIR false
 
 // @section homing
+//#define MIN_Z_HEIGHT_FOR_HOMING 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
+                                    // Be sure you have this distance over your Z_MAX_POS in case.
 
 // ENDSTOP SETTINGS:
 // Sets direction of endstops when homing; 1=MAX, -1=MIN
@@ -509,9 +511,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
   #define Y_PROBE_OFFSET_FROM_EXTRUDER -29     // Z offset: -front [of the nozzle] +behind
   #define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35  // Z offset: -below [the nozzle] (always negative!)
 
-  #define Z_RAISE_BEFORE_HOMING 4       // (in mm) Raise Z axis before homing (G28) for Z probe clearance.
-                                        // Be sure you have this distance over your Z_MAX_POS in case.
-
   #define XY_TRAVEL_SPEED 8000         // X and Y axis travel speed between probes, in mm/min.
 
   #define Z_RAISE_BEFORE_PROBING 15   // How much the Z axis will be raised before traveling to the first probing point.

Marlin/example_configurations/delta/biv2.5/Configuration.h

@@ -413,6 +413,8 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
 #define INVERT_E3_DIR false
 
 // @section homing
+//#define MIN_Z_HEIGHT_FOR_HOMING 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
+                                    // Be sure you have this distance over your Z_MAX_POS in case.
 
 // ENDSTOP SETTINGS:
 // Sets direction of endstops when homing; 1=MAX, -1=MIN
@@ -548,9 +550,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
   #define Y_PROBE_OFFSET_FROM_EXTRUDER -10   // Z offset: -front [of the nozzle] +behind
   #define Z_PROBE_OFFSET_FROM_EXTRUDER -3.5  // Z offset: -below [the nozzle] (always negative!)
 
-  #define Z_RAISE_BEFORE_HOMING 4       // (in mm) Raise Z axis before homing (G28) for Z probe clearance.
-                                        // Be sure you have this distance over your Z_MAX_POS in case.
-
   #define XY_TRAVEL_SPEED 4000         // X and Y axis travel speed between probes, in mm/min.
 
   #define Z_RAISE_BEFORE_PROBING 15   // How much the Z axis will be raised before traveling to the first probing point.

Marlin/example_configurations/delta/generic/Configuration.h

@@ -413,6 +413,8 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
 #define INVERT_E3_DIR false
 
 // @section homing
+//#define MIN_Z_HEIGHT_FOR_HOMING 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
+                                    // Be sure you have this distance over your Z_MAX_POS in case.
 
 // ENDSTOP SETTINGS:
 // Sets direction of endstops when homing; 1=MAX, -1=MIN
@@ -548,9 +550,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
   #define Y_PROBE_OFFSET_FROM_EXTRUDER -10   // Z probe to nozzle Y offset: -front +behind
   #define Z_PROBE_OFFSET_FROM_EXTRUDER -3.5  // Z probe to nozzle Z offset: -below (always!)
 
-  #define Z_RAISE_BEFORE_HOMING 4       // (in mm) Raise Z axis before homing (G28) for Z probe clearance.
-                                        // Be sure you have this distance over your Z_MAX_POS in case.
-
   #define XY_TRAVEL_SPEED 4000         // X and Y axis travel speed between probes, in mm/min.
 
   #define Z_RAISE_BEFORE_PROBING 15   // How much the Z axis will be raised before traveling to the first probing point.

Marlin/example_configurations/delta/kossel_mini/Configuration.h

@@ -413,6 +413,8 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 #define INVERT_E3_DIR false
 
 // @section homing
+//#define MIN_Z_HEIGHT_FOR_HOMING 15// (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
+                                    // Be sure you have this distance over your Z_MAX_POS in case.
 
 // ENDSTOP SETTINGS:
 // Sets direction of endstops when homing; 1=MAX, -1=MIN
@@ -548,9 +550,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
   #define Y_PROBE_OFFSET_FROM_EXTRUDER -10   // Z offset: -front [of the nozzle] +behind
   #define Z_PROBE_OFFSET_FROM_EXTRUDER -3.5  // Z offset: -below [the nozzle] (always negative!)
 
-  #define Z_RAISE_BEFORE_HOMING 15      // (in mm) Raise Z axis before homing (G28) for Z probe clearance.
-                                        // Be sure you have this distance over your Z_MAX_POS in case.
-
   #define XY_TRAVEL_SPEED 4000         // X and Y axis travel speed between probes, in mm/min.
 
   #define Z_RAISE_BEFORE_PROBING 15   // How much the Z axis will be raised before traveling to the first probing point.

Marlin/example_configurations/delta/kossel_pro/Configuration.h

@@ -400,6 +400,8 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 #define INVERT_E3_DIR false
 
 // @section homing
+//#define MIN_Z_HEIGHT_FOR_HOMING 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
+                                    // Be sure you have this distance over your Z_MAX_POS in case.
 
 // ENDSTOP SETTINGS:
 // Sets direction of endstops when homing; 1=MAX, -1=MIN
@@ -537,9 +539,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
   // not giving someone a head crash. Use something like G29 Z-0.2 to adjust as needed.
   #define Z_PROBE_OFFSET_FROM_EXTRUDER -17.25  // Increase this if the first layer is too thin (remember: it's a negative number so increase means closer to zero).
 
-  #define Z_RAISE_BEFORE_HOMING 4       // (in mm) Raise Z axis before homing (G28) for Z probe clearance.
-                                        // Be sure you have this distance over your Z_MAX_POS in case.
-
   #define XY_TRAVEL_SPEED 8000         // X and Y axis travel speed between probes, in mm/min.
 
   #define Z_RAISE_BEFORE_PROBING 100  // How much the Z axis will be raised before traveling to the first probing point.

Marlin/example_configurations/delta/kossel_xl/Configuration.h

@@ -406,6 +406,8 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 #define INVERT_E3_DIR false
 
 // @section homing
+//#define MIN_Z_HEIGHT_FOR_HOMING 7 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
+                                    // Be sure you have this distance over your Z_MAX_POS in case.
 
 // ENDSTOP SETTINGS:
 // Sets direction of endstops when homing; 1=MAX, -1=MIN
@@ -540,9 +542,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
   #define Y_PROBE_OFFSET_FROM_EXTRUDER 0.0     // Z offset: -front [of the nozzle] +behind
   #define Z_PROBE_OFFSET_FROM_EXTRUDER 0.3     // Z offset: -below [the nozzle] (always negative!)
 
-  #define Z_RAISE_BEFORE_HOMING 7       // (in mm) Raise Z axis before homing (G28) for Z probe clearance.
-                                        // Be sure you have this distance over your Z_MAX_POS in case.
-
   #define XY_TRAVEL_SPEED 7000         // X and Y axis travel speed between probes, in mm/min.
 
   #define Z_RAISE_BEFORE_PROBING 20   // How much the Z axis will be raised before traveling to the first probing point.

Marlin/example_configurations/makibox/Configuration.h

@@ -381,6 +381,8 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 #define INVERT_E3_DIR false
 
 // @section homing
+//#define MIN_Z_HEIGHT_FOR_HOMING 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
+                                    // Be sure you have this distance over your Z_MAX_POS in case.
 
 // ENDSTOP SETTINGS:
 // Sets direction of endstops when homing; 1=MAX, -1=MIN
@@ -512,9 +514,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
   #define Y_PROBE_OFFSET_FROM_EXTRUDER -29     // Z offset: -front [of the nozzle] +behind
   #define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35  // Z offset: -below [the nozzle] (always negative!)
 
-  #define Z_RAISE_BEFORE_HOMING 4       // (in mm) Raise Z axis before homing (G28) for Z probe clearance.
-                                        // Be sure you have this distance over your Z_MAX_POS in case.
-
   #define XY_TRAVEL_SPEED 8000         // X and Y axis travel speed between probes, in mm/min.
 
   #define Z_RAISE_BEFORE_PROBING 15   // How much the Z axis will be raised before traveling to the first probing point.

Marlin/example_configurations/tvrrug/Round2/Configuration.h

@@ -368,6 +368,8 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
 #define INVERT_E3_DIR false
 
 // @section homing
+//#define MIN_Z_HEIGHT_FOR_HOMING 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
+                                    // Be sure you have this distance over your Z_MAX_POS in case.
 
 // ENDSTOP SETTINGS:
 // Sets direction of endstops when homing; 1=MAX, -1=MIN
@@ -499,9 +501,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
   #define Y_PROBE_OFFSET_FROM_EXTRUDER -29     // Z offset: -front [of the nozzle] +behind
   #define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35  // Z offset: -below [the nozzle] (always negative!)
 
-  #define Z_RAISE_BEFORE_HOMING 4       // (in mm) Raise Z axis before homing (G28) for Z probe clearance.
-                                        // Be sure you have this distance over your Z_MAX_POS in case.
-
   #define XY_TRAVEL_SPEED 8000         // X and Y axis travel speed between probes, in mm/min.
 
   #define Z_RAISE_BEFORE_PROBING 15   // How much the Z axis will be raised before traveling to the first probing point.