Merge pull request #2115 from AnHardt/_temp_error

Use _temp_error() for all errors thrown by different heater sanity check mechanisms

Marlin/language.h

@@ -223,15 +223,16 @@
 #define MSG_PID_DEBUG_PTERM                 " pTerm "
 #define MSG_PID_DEBUG_ITERM                 " iTerm "
 #define MSG_PID_DEBUG_DTERM                 " dTerm "
-#define MSG_HEATING_FAILED                  "Heating failed"
-#define MSG_EXTRUDER_SWITCHED_OFF           "Extruder switched off. Temperature difference between temp sensors is too high !"
-
 #define MSG_INVALID_EXTRUDER_NUM            " - Invalid extruder number !"
-#define MSG_THERMAL_RUNAWAY_STOP            "Thermal Runaway, system stopped! Heater_ID: "
-#define MSG_SWITCHED_OFF_MAX                " switched off. MAXTEMP triggered !!"
-#define MSG_MINTEMP_EXTRUDER_OFF            ": Extruder switched off. MINTEMP triggered !"
-#define MSG_MAXTEMP_EXTRUDER_OFF            ": Extruder" MSG_SWITCHED_OFF_MAX
-#define MSG_MAXTEMP_BED_OFF                 "Heated bed" MSG_SWITCHED_OFF_MAX
+
+#define MSG_HEATER_BED                      "bed"
+#define MSG_STOPPED_HEATER                  ", system stopped! Heater_ID: "
+#define MSG_REDUNDANCY                      "Heater switched off. Temperature difference between temp sensors is too high !"
+#define MSG_T_HEATING_FAILED                "Heating failed"
+#define MSG_T_THERMAL_RUNAWAY               "Thermal Runaway"
+#define MSG_T_MAXTEMP                       "MAXTEMP triggered"
+#define MSG_T_MINTEMP                       "MINTEMP triggered"
+
 
 // LCD Menu Messages
 

Marlin/temperature.cpp

@@ -450,31 +450,28 @@ void checkExtruderAutoFans()
 inline void _temp_error(int e, const char *serial_msg, const char *lcd_msg) {
   if (IsRunning()) {
     SERIAL_ERROR_START;
-    if (e >= 0) SERIAL_ERRORLN((int)e);
     serialprintPGM(serial_msg);
-    MYSERIAL.write('\n');
-    #ifdef ULTRA_LCD
-      lcd_setalertstatuspgm(lcd_msg);
-    #endif
+    SERIAL_ERRORPGM(MSG_STOPPED_HEATER);
+    if (e >= 0) SERIAL_ERRORLN((int)e); else SERIAL_ERRORLNPGM(MSG_HEATER_BED);
   }
   #ifndef BOGUS_TEMPERATURE_FAILSAFE_OVERRIDE
-    Stop();
+    kill(lcd_msg);
   #endif
 }
 
 void max_temp_error(uint8_t e) {
   disable_all_heaters();
-  _temp_error(e, PSTR(MSG_MAXTEMP_EXTRUDER_OFF), PSTR(MSG_ERR_MAXTEMP));
+  _temp_error(e, PSTR(MSG_T_MAXTEMP), PSTR(MSG_ERR_MAXTEMP));
 }
 void min_temp_error(uint8_t e) {
   disable_all_heaters();
-  _temp_error(e, PSTR(MSG_MINTEMP_EXTRUDER_OFF), PSTR(MSG_ERR_MINTEMP));
+  _temp_error(e, PSTR(MSG_T_MINTEMP), PSTR(MSG_ERR_MINTEMP));
 }
 void bed_max_temp_error(void) {
   #if HAS_HEATER_BED
     WRITE_HEATER_BED(0);
   #endif
-  _temp_error(-1, PSTR(MSG_MAXTEMP_BED_OFF), PSTR(MSG_ERR_MAXTEMP_BED));
+  _temp_error(-1, PSTR(MSG_T_MAXTEMP), PSTR(MSG_ERR_MAXTEMP_BED));
 }
 
 float get_pid_output(int e) {
@@ -628,8 +625,7 @@ void manage_heater() {
         // Has it failed to increase enough?
         if (degHotend(e) < watch_target_temp[e]) {
           // Stop!
-          disable_all_heaters();
-          _temp_error(e, PSTR(MSG_HEATING_FAILED), PSTR(MSG_HEATING_FAILED_LCD));
+          _temp_error(e, PSTR(MSG_T_HEATING_FAILED), PSTR(MSG_HEATING_FAILED_LCD));
         }
         else {
           // Start again if the target is still far off
@@ -1071,16 +1067,7 @@ void tp_init() {
           *state = TRRunaway;
         break;
       case TRRunaway:
-        SERIAL_ERROR_START;
-        SERIAL_ERRORLNPGM(MSG_THERMAL_RUNAWAY_STOP);
-        if (heater_id < 0) SERIAL_ERRORLNPGM("bed"); else SERIAL_ERRORLN(heater_id);
-        LCD_ALERTMESSAGEPGM(MSG_THERMAL_RUNAWAY);
-        disable_all_heaters();
-        disable_all_steppers();
-        for (;;) {
-          manage_heater();
-          lcd_update();
-        }
+        _temp_error(heater_id, PSTR(MSG_T_THERMAL_RUNAWAY), PSTR(MSG_THERMAL_RUNAWAY));
     }
   }