One for common settings. One for advanced settings.master
parent
f9c5333f97
commit
d8a0c6450f
@ -0,0 +1,208 @@
|
||||
#ifndef __CONFIGURATION_ADV_H
|
||||
#define __CONFIGURATION_ADV_H
|
||||
|
||||
//===========================================================================
|
||||
//=============================Thermal Settings ============================
|
||||
//===========================================================================
|
||||
|
||||
// Select one of these only to define how the bed temp is read.
|
||||
//
|
||||
//#define BED_LIMIT_SWITCHING
|
||||
#ifdef BED_LIMIT_SWITCHING
|
||||
#define BED_HYSTERESIS 2 //only disable heating if T>target+BED_HYSTERESIS and enable heating if T>target-BED_HYSTERESIS
|
||||
#endif
|
||||
#define BED_CHECK_INTERVAL 5000 //ms
|
||||
|
||||
//// Heating sanity check:
|
||||
// This waits for the watchperiod in milliseconds whenever an M104 or M109 increases the target temperature
|
||||
// If the temperature has not increased at the end of that period, the target temperature is set to zero.
|
||||
// It can be reset with another M104/M109
|
||||
//#define WATCHPERIOD 20000 //20 seconds
|
||||
|
||||
// Wait for Cooldown
|
||||
// This defines if the M109 call should not block if it is cooling down.
|
||||
// example: From a current temp of 220, you set M109 S200.
|
||||
// if CooldownNoWait is defined M109 will not wait for the cooldown to finish
|
||||
#define CooldownNoWait true
|
||||
|
||||
// Heating is finished if a temperature close to this degree shift is reached
|
||||
#define HEATING_EARLY_FINISH_DEG_OFFSET 1 //Degree
|
||||
|
||||
//Do not wait for M109 to finish when printing from SD card
|
||||
//#define STOP_HEATING_WAIT_WHEN_SD_PRINTING
|
||||
|
||||
#ifdef PIDTEMP
|
||||
// this adds an experimental additional term to the heatingpower, proportional to the extrusion speed.
|
||||
// if Kc is choosen well, the additional required power due to increased melting should be compensated.
|
||||
#define PID_ADD_EXTRUSION_RATE
|
||||
#ifdef PID_ADD_EXTRUSION_RATE
|
||||
#define DEFAULT_Kc (1) //heatingpower=Kc*(e_speed)
|
||||
#endif
|
||||
#endif
|
||||
|
||||
|
||||
//automatic temperature: The hot end target temperature is calculated by all the buffered lines of gcode.
|
||||
//The maximum buffered steps/sec of the extruder motor are called "se".
|
||||
//You enter the autotemp mode by a M109 S<mintemp> T<maxtemp> F<factor>
|
||||
// the target temperature is set to mintemp+factor*se[steps/sec] and limited by mintemp and maxtemp
|
||||
// you exit the value by any M109 without F*
|
||||
// Also, if the temperature is set to a value <mintemp, it is not changed by autotemp.
|
||||
// on an ultimaker, some initial testing worked with M109 S215 T260 F0.1 in the start.gcode
|
||||
//#define AUTOTEMP
|
||||
#ifdef AUTOTEMP
|
||||
#define AUTOTEMP_OLDWEIGHT 0.98
|
||||
#endif
|
||||
|
||||
// extruder run-out prevention.
|
||||
//if the machine is idle, and the temperature over MINTEMP, every couple of SECONDS some filament is extruded
|
||||
//#define EXTRUDER_RUNOUT_PREVENT
|
||||
#define EXTRUDER_RUNOUT_MINTEMP 190
|
||||
#define EXTRUDER_RUNOUT_SECONDS 30.
|
||||
#define EXTRUDER_RUNOUT_ESTEPS 14. //mm filament
|
||||
#define EXTRUDER_RUNOUT_SPEED 1500. //extrusion speed
|
||||
#define EXTRUDER_RUNOUT_EXTRUDE 100
|
||||
|
||||
//===========================================================================
|
||||
//=============================Mechanical Settings===========================
|
||||
//===========================================================================
|
||||
|
||||
// This defines the number of extruders
|
||||
#define EXTRUDERS 1
|
||||
|
||||
#define ENDSTOPS_ONLY_FOR_HOMING // If defined the endstops will only be used for homing
|
||||
|
||||
//#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
|
||||
|
||||
//homing hits the endstop, then retracts by this distance, before it tries to slowly bump again:
|
||||
#define X_HOME_RETRACT_MM 5
|
||||
#define Y_HOME_RETRACT_MM 5
|
||||
#define Z_HOME_RETRACT_MM 1
|
||||
#define QUICK_HOME //if this is defined, if both x and y are to be homed, a diagonal move will be performed initially.
|
||||
|
||||
#define AXIS_RELATIVE_MODES {false, false, false, false}
|
||||
|
||||
#define MAX_STEP_FREQUENCY 40000 // Max step frequency for Ultimaker (5000 pps / half step)
|
||||
|
||||
//default stepper release if idle
|
||||
#define DEFAULT_STEPPER_DEACTIVE_TIME 60
|
||||
#define DEFAULT_STEPPER_DEACTIVE_COMMAND "M84 X Y E" //z stays powered
|
||||
|
||||
#define DEFAULT_MINIMUMFEEDRATE 0.0 // minimum feedrate
|
||||
#define DEFAULT_MINTRAVELFEEDRATE 0.0
|
||||
|
||||
// minimum time in microseconds that a movement needs to take if the buffer is emptied. Increase this number if you see blobs while printing high speed & high detail. It will slowdown on the detailed stuff.
|
||||
#define DEFAULT_MINSEGMENTTIME 20000 // Obsolete delete this
|
||||
|
||||
// If defined the movements slow down when the look ahead buffer is only half full
|
||||
#define SLOWDOWN
|
||||
|
||||
// Frequency limit
|
||||
// See nophead's blog for more info
|
||||
// Not working O
|
||||
//#define XY_FREQUENCY_LIMIT 15
|
||||
|
||||
// Minimum planner junction speed. Sets the default minimum speed the planner plans for at the end
|
||||
// of the buffer and all stops. This should not be much greater than zero and should only be changed
|
||||
// if unwanted behavior is observed on a user's machine when running at very slow speeds.
|
||||
#define MINIMUM_PLANNER_SPEED 2.0 // (mm/sec)
|
||||
|
||||
//===========================================================================
|
||||
//=============================Additional Features===========================
|
||||
//===========================================================================
|
||||
|
||||
|
||||
#define SD_FINISHED_STEPPERRELEASE true //if sd support and the file is finished: disable steppers?
|
||||
#define SD_FINISHED_RELEASECOMMAND "M84 X Y E" // no z because of layer shift.
|
||||
|
||||
// The hardware watchdog should halt the Microcontroller, in case the firmware gets stuck somewhere. However:
|
||||
// the Watchdog is not working well, so please only enable this for testing
|
||||
// this enables the watchdog interrupt.
|
||||
//#define USE_WATCHDOG
|
||||
//#ifdef USE_WATCHDOG
|
||||
// you cannot reboot on a mega2560 due to a bug in he bootloader. Hence, you have to reset manually, and this is done hereby:
|
||||
//#define RESET_MANUAL
|
||||
//#define WATCHDOG_TIMEOUT 4 //seconds
|
||||
//#endif
|
||||
|
||||
// extruder advance constant (s2/mm3)
|
||||
//
|
||||
// advance (steps) = STEPS_PER_CUBIC_MM_E * EXTUDER_ADVANCE_K * cubic mm per second ^ 2
|
||||
//
|
||||
// hooke's law says: force = k * distance
|
||||
// bernoulli's priniciple says: v ^ 2 / 2 + g . h + pressure / density = constant
|
||||
// so: v ^ 2 is proportional to number of steps we advance the extruder
|
||||
//#define ADVANCE
|
||||
|
||||
#ifdef ADVANCE
|
||||
#define EXTRUDER_ADVANCE_K .0
|
||||
|
||||
#define D_FILAMENT 2.85
|
||||
#define STEPS_MM_E 836
|
||||
#define EXTRUTION_AREA (0.25 * D_FILAMENT * D_FILAMENT * 3.14159)
|
||||
#define STEPS_PER_CUBIC_MM_E (axis_steps_per_unit[E_AXIS]/ EXTRUTION_AREA)
|
||||
|
||||
#endif // ADVANCE
|
||||
|
||||
// A debugging feature to compare calculated vs performed steps, to see if steps are lost by the software.
|
||||
//#define DEBUG_STEPS
|
||||
|
||||
// Arc interpretation settings:
|
||||
#define MM_PER_ARC_SEGMENT 1
|
||||
#define N_ARC_CORRECTION 25
|
||||
|
||||
const int dropsegments=5; //everything with less than this number of steps will be ignored as move and joined with the next movement
|
||||
|
||||
//===========================================================================
|
||||
//=============================Buffers ============================
|
||||
//===========================================================================
|
||||
|
||||
// The number of linear motions that can be in the plan at any give time.
|
||||
// THE BLOCK_BUFFER_SIZE NEEDS TO BE A POWER OF 2, i.g. 8,16,32 because shifts and ors are used to do the ringbuffering.
|
||||
#if defined SDSUPPORT
|
||||
#define BLOCK_BUFFER_SIZE 16 // SD,LCD,Buttons take more memory, block buffer needs to be smaller
|
||||
#else
|
||||
#define BLOCK_BUFFER_SIZE 16 // maximize block buffer
|
||||
#endif
|
||||
|
||||
|
||||
//The ASCII buffer for recieving from the serial:
|
||||
#define MAX_CMD_SIZE 96
|
||||
#define BUFSIZE 4
|
||||
|
||||
//===========================================================================
|
||||
//============================= Define Defines ============================
|
||||
//===========================================================================
|
||||
|
||||
#if TEMP_SENSOR_0 > 0
|
||||
#define THERMISTORHEATER_0 TEMP_SENSOR_0
|
||||
#define HEATER_0_USES_THERMISTOR
|
||||
#endif
|
||||
#if TEMP_SENSOR_1 > 0
|
||||
#define THERMISTORHEATER_1 TEMP_SENSOR_1
|
||||
#define HEATER_1_USES_THERMISTOR
|
||||
#endif
|
||||
#if TEMP_SENSOR_2 > 0
|
||||
#define THERMISTORHEATER_2 TEMP_SENSOR_2
|
||||
#define HEATER_2_USES_THERMISTOR
|
||||
#endif
|
||||
#if TEMP_SENSOR_BED > 0
|
||||
#define THERMISTORBED TEMP_SENSOR_BED
|
||||
#define BED_USES_THERMISTOR
|
||||
#endif
|
||||
#if TEMP_SENSOR_0 == -1
|
||||
#define HEATER_0_USES_AD595
|
||||
#endif
|
||||
#if TEMP_SENSOR_1 == -1
|
||||
#define HEATER_1_USES_AD595
|
||||
#endif
|
||||
#if TEMP_SENSOR_2 == -1
|
||||
#define HEATER_2_USES_AD595
|
||||
#endif
|
||||
#if TEMP_SENSOR_BED == -1
|
||||
#define BED_USES_AD595
|
||||
#endif
|
||||
#if TEMP_SENSOR_0 == -2
|
||||
#define HEATER_0_USES_MAX6675
|
||||
#endif
|
||||
|
||||
#endif //__CONFIGURATION_ADV_H
|
Loading…
Reference in new issue