Merge pull request #7128 from thinkyhead/bf_enhanced_arcs

Enhance G2/G3 with 'P' and G17/G18/G19 Plane Select

.travis.yml

@@ -72,14 +72,14 @@ script:
   - build_marlin
   #
   # Test 2 extruders (one MAX6675) and heated bed on basic RAMPS 1.4
-  #  plus a "Fix Mounted" Probe with Safe Homing
+  #  plus a "Fix Mounted" Probe with Safe Homing and some arc options
   #
   - opt_set MOTHERBOARD BOARD_RAMPS_14_EEB
   - opt_set EXTRUDERS 2
   - opt_set TEMP_SENSOR_0 -2
   - opt_set TEMP_SENSOR_1 1
   - opt_set TEMP_SENSOR_BED 1
-  - opt_enable PIDTEMPBED FIX_MOUNTED_PROBE Z_SAFE_HOMING
+  - opt_enable PIDTEMPBED FIX_MOUNTED_PROBE Z_SAFE_HOMING ARC_P_CIRCLES CNC_WORKSPACE_PLANES
   - build_marlin
   #
   # ...with AUTO_BED_LEVELING_LINEAR, Z_MIN_PROBE_REPEATABILITY_TEST, and DEBUG_LEVELING_FEATURE

Marlin/Conditionals_LCD.h

@@ -108,6 +108,9 @@
 
   #if ENABLED(REPRAPWORLD_KEYPAD)
     #define NEWPANEL
+    #if ENABLED(ULTIPANEL) && !defined(REPRAPWORLD_KEYPAD_MOVE_STEP)
+      #define REPRAPWORLD_KEYPAD_MOVE_STEP 1.0
+    #endif
   #endif
 
   #if ENABLED(RA_CONTROL_PANEL)

Marlin/Configuration_adv.h

@@ -678,10 +678,16 @@
 
 // @section extras
 
-// Arc interpretation settings:
+//
-#define ARC_SUPPORT  // Disabling this saves ~2738 bytes
+// G2/G3 Arc Support
-#define MM_PER_ARC_SEGMENT 1
+//
-#define N_ARC_CORRECTION 25
+#define ARC_SUPPORT               // Disable this feature to save ~3226 bytes
+#if ENABLED(ARC_SUPPORT)
+  #define MM_PER_ARC_SEGMENT  1   // Length of each arc segment
+  #define N_ARC_CORRECTION   25   // Number of intertpolated segments between corrections
+  //#define ARC_P_CIRCLES         // Enable the 'P' parameter to specify complete circles
+  //#define CNC_WORKSPACE_PLANES  // Allow G2/G3 to operate in XY, ZX, or YZ planes
+#endif
 
 // Support for G5 with XYZE destination and IJPQ offsets. Requires ~2666 bytes.
 //#define BEZIER_CURVE_SUPPORT

Marlin/Marlin.h

@@ -370,9 +370,9 @@ extern float soft_endstop_min[XYZ], soft_endstop_max[XYZ];
   extern bool filament_sensor;         // Flag that filament sensor readings should control extrusion
   extern float filament_width_nominal, // Theoretical filament diameter i.e., 3.00 or 1.75
                filament_width_meas;    // Measured filament diameter
-  extern int8_t measurement_delay[];   // Ring buffer to delay measurement
+  extern uint8_t meas_delay_cm,        // Delay distance
-  extern int filwidth_delay_index[2];  // Ring buffer indexes. Used by planner, temperature, and main code
+                 measurement_delay[];  // Ring buffer to delay measurement
-  extern int meas_delay_cm;            // Delay distance
+  extern int8_t filwidth_delay_index[2]; // Ring buffer indexes. Used by planner, temperature, and main code
 #endif
 
 #if ENABLED(ADVANCED_PAUSE_FEATURE)

Marlin/Marlin_main.cpp

@@ -54,6 +54,9 @@
  * G10  - Retract filament according to settings of M207
  * G11  - Retract recover filament according to settings of M208
  * G12  - Clean tool
+ * G17  - Select Plane XY (Requires CNC_WORKSPACE_PLANES)
+ * G18  - Select Plane ZX (Requires CNC_WORKSPACE_PLANES)
+ * G19  - Select Plane YZ (Requires CNC_WORKSPACE_PLANES)
  * G20  - Set input units to inches
  * G21  - Set input units to millimeters
  * G26  - Mesh Validation Pattern (Requires UBL_G26_MESH_VALIDATION)
@@ -73,7 +76,7 @@
  * "M" Codes
  *
  * M0   - Unconditional stop - Wait for user to press a button on the LCD (Only if ULTRA_LCD is enabled)
- * M1   - Same as M0
+ * M1   -> M0
  * M3   - Turn laser/spindle on, set spindle/laser speed/power, set rotation to clockwise
  * M4   - Turn laser/spindle on, set spindle/laser speed/power, set rotation to counter-clockwise
  * M5   - Turn laser/spindle off
@@ -630,9 +633,9 @@ float cartes[XYZ] = { 0 };
   bool filament_sensor = false;                                 // M405 turns on filament sensor control. M406 turns it off.
   float filament_width_nominal = DEFAULT_NOMINAL_FILAMENT_DIA,  // Nominal filament width. Change with M404.
         filament_width_meas = DEFAULT_MEASURED_FILAMENT_DIA;    // Measured filament diameter
-  int8_t measurement_delay[MAX_MEASUREMENT_DELAY + 1];          // Ring buffer to delayed measurement. Store extruder factor after subtracting 100
+  uint8_t meas_delay_cm = MEASUREMENT_DELAY_CM,                 // Distance delay setting
-  int filwidth_delay_index[2] = { 0, -1 };                      // Indexes into ring buffer
+          measurement_delay[MAX_MEASUREMENT_DELAY + 1];         // Ring buffer to delayed measurement. Store extruder factor after subtracting 100
-  int meas_delay_cm = MEASUREMENT_DELAY_CM;                     // Distance delay setting
+  int8_t filwidth_delay_index[2] = { 0, -1 };                   // Indexes into ring buffer
 #endif
 
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
@@ -688,6 +691,10 @@ static bool send_ok[BUFSIZE];
   millis_t lastUpdateMillis;
 #endif
 
+#if ENABLED(CNC_WORKSPACE_PLANES)
+  static WorkspacePlane workspace_plane = PLANE_XY;
+#endif
+
 FORCE_INLINE float pgm_read_any(const float *p) { return pgm_read_float_near(p); }
 FORCE_INLINE signed char pgm_read_any(const signed char *p) { return pgm_read_byte_near(p); }
 
@@ -3264,12 +3271,16 @@ inline void gcode_G0_G1(
  *    X or Y must differ from the current XY.
  *    Mixing R with I or J will throw an error.
  *
+ *  - P specifies the number of full circles to do
+ *    before the specified arc move.
+ *
  *  Examples:
  *
  *    G2 I10           ; CW circle centered at X+10
  *    G3 X20 Y12 R14   ; CCW circle with r=14 ending at X20 Y12
  */
 #if ENABLED(ARC_SUPPORT)
+
   inline void gcode_G2_G3(bool clockwise) {
     if (IsRunning()) {
 
@@ -3287,27 +3298,39 @@ inline void gcode_G0_G1(
       float arc_offset[2] = { 0.0, 0.0 };
       if (parser.seen('R')) {
         const float r = parser.value_linear_units(),
-                    x1 = current_position[X_AXIS], y1 = current_position[Y_AXIS],
+                    p1 = current_position[X_AXIS], q1 = current_position[Y_AXIS],
-                    x2 = destination[X_AXIS], y2 = destination[Y_AXIS];
+                    p2 = destination[X_AXIS], q2 = destination[Y_AXIS];
-        if (r && (x2 != x1 || y2 != y1)) {
+        if (r && (p2 != p1 || q2 != q1)) {
           const float e = clockwise ^ (r < 0) ? -1 : 1,           // clockwise -1/1, counterclockwise 1/-1
-                      dx = x2 - x1, dy = y2 - y1,                 // X and Y differences
+                      dx = p2 - p1, dy = q2 - q1,                 // X and Y differences
                       d = HYPOT(dx, dy),                          // Linear distance between the points
                       h = SQRT(sq(r) - sq(d * 0.5)),              // Distance to the arc pivot-point
-                      mx = (x1 + x2) * 0.5, my = (y1 + y2) * 0.5, // Point between the two points
+                      mx = (p1 + p2) * 0.5, my = (q1 + q2) * 0.5, // Point between the two points
                       sx = -dy / d, sy = dx / d,                  // Slope of the perpendicular bisector
                       cx = mx + e * h * sx, cy = my + e * h * sy; // Pivot-point of the arc
-          arc_offset[X_AXIS] = cx - x1;
+          arc_offset[0] = cx - p1;
-          arc_offset[Y_AXIS] = cy - y1;
+          arc_offset[1] = cy - q1;
         }
       }
       else {
-        if (parser.seen('I')) arc_offset[X_AXIS] = parser.value_linear_units();
+        if (parser.seen('I')) arc_offset[0] = parser.value_linear_units();
-        if (parser.seen('J')) arc_offset[Y_AXIS] = parser.value_linear_units();
+        if (parser.seen('J')) arc_offset[1] = parser.value_linear_units();
       }
 
       if (arc_offset[0] || arc_offset[1]) {
-        // Send an arc to the planner
+
+        #if ENABLED(ARC_P_CIRCLES)
+          // P indicates number of circles to do
+          int8_t circles_to_do = parser.seen('P') ? parser.value_byte() : 0;
+          if (!WITHIN(circles_to_do, 0, 100)) {
+            SERIAL_ERROR_START();
+            SERIAL_ERRORLNPGM(MSG_ERR_ARC_ARGS);
+          }
+          while (circles_to_do--)
+            plan_arc(current_position, arc_offset, clockwise);
+        #endif
+
+        // Send the arc to the planner
         plan_arc(destination, arc_offset, clockwise);
         refresh_cmd_timeout();
       }
@@ -3318,7 +3341,8 @@ inline void gcode_G0_G1(
       }
     }
   }
-#endif
+
+#endif // ARC_SUPPORT
 
 /**
  * G4: Dwell S<seconds> or P<milliseconds>
@@ -3406,6 +3430,25 @@ inline void gcode_G4() {
   }
 #endif
 
+#if ENABLED(CNC_WORKSPACE_PLANES)
+
+  void report_workspace_plane() {
+    SERIAL_ECHO_START();
+    SERIAL_ECHOPGM("Workspace Plane ");
+    serialprintPGM(workspace_plane == PLANE_YZ ? PSTR("YZ\n") : workspace_plane == PLANE_ZX ? PSTR("ZX\n") : PSTR("XY\n"));
+  }
+
+  /**
+   * G17: Select Plane XY
+   * G18: Select Plane ZX
+   * G19: Select Plane YZ
+   */
+  inline void gcode_G17() { workspace_plane = PLANE_XY; }
+  inline void gcode_G18() { workspace_plane = PLANE_ZX; }
+  inline void gcode_G19() { workspace_plane = PLANE_YZ; }
+
+#endif // CNC_WORKSPACE_PLANES
+
 #if ENABLED(INCH_MODE_SUPPORT)
   /**
    * G20: Set input mode to inches
@@ -3720,6 +3763,10 @@ inline void gcode_G28(const bool always_home_all) {
     set_bed_leveling_enabled(false);
   #endif
 
+  #if ENABLED(CNC_WORKSPACE_PLANES)
+    workspace_plane = PLANE_XY;
+  #endif
+
   // Always home with tool 0 active
   #if HOTENDS > 1
     const uint8_t old_tool_index = active_extruder;
@@ -8898,11 +8945,11 @@ inline void gcode_M400() { stepper.synchronize(); }
   inline void gcode_M405() {
     // This is technically a linear measurement, but since it's quantized to centimeters and is a different unit than
     // everything else, it uses parser.value_int() instead of parser.value_linear_units().
-    if (parser.seen('D')) meas_delay_cm = parser.value_int();
+    if (parser.seen('D')) meas_delay_cm = parser.value_byte();
     NOMORE(meas_delay_cm, MAX_MEASUREMENT_DELAY);
 
     if (filwidth_delay_index[1] == -1) { // Initialize the ring buffer if not done since startup
-      const int temp_ratio = thermalManager.widthFil_to_size_ratio() - 100; // -100 to scale within a signed byte
+      const uint8_t temp_ratio = thermalManager.widthFil_to_size_ratio() - 100; // -100 to scale within a signed byte
 
       for (uint8_t i = 0; i < COUNT(measurement_delay); ++i)
         measurement_delay[i] = temp_ratio;
@@ -10309,6 +10356,18 @@ void process_next_command() {
           break;
       #endif // NOZZLE_CLEAN_FEATURE
 
+      #if ENABLED(CNC_WORKSPACE_PLANES)
+        case 17: // G17: Select Plane XY
+          gcode_G17();
+          break;
+        case 18: // G18: Select Plane ZX
+          gcode_G18();
+          break;
+        case 19: // G19: Select Plane YZ
+          gcode_G19();
+          break;
+      #endif // CNC_WORKSPACE_PLANES
+
       #if ENABLED(INCH_MODE_SUPPORT)
         case 20: //G20: Inch Mode
           gcode_G20();
@@ -11920,6 +11979,12 @@ void prepare_move_to_destination() {
 }
 
 #if ENABLED(ARC_SUPPORT)
+
+  #if N_ARC_CORRECTION < 1
+    #undef N_ARC_CORRECTION
+    #define N_ARC_CORRECTION 1
+  #endif
+
   /**
    * Plan an arc in 2 dimensions
    *
@@ -11934,26 +11999,36 @@ void prepare_move_to_destination() {
     float *offset,       // Center of rotation relative to current_position
     uint8_t clockwise    // Clockwise?
   ) {
+    #if ENABLED(CNC_WORKSPACE_PLANES)
+      AxisEnum p_axis, q_axis, l_axis;
+      switch (workspace_plane) {
+        case PLANE_XY: p_axis = X_AXIS; q_axis = Y_AXIS; l_axis = Z_AXIS; break;
+        case PLANE_ZX: p_axis = Z_AXIS; q_axis = X_AXIS; l_axis = Y_AXIS; break;
+        case PLANE_YZ: p_axis = Y_AXIS; q_axis = Z_AXIS; l_axis = X_AXIS; break;
+      }
+    #else
+      constexpr AxisEnum p_axis = X_AXIS, q_axis = Y_AXIS, l_axis = Z_AXIS;
+    #endif
 
-    float r_X = -offset[X_AXIS],  // Radius vector from center to current location
+    // Radius vector from center to current location
-          r_Y = -offset[Y_AXIS];
+    float r_P = -offset[0], r_Q = -offset[1];
 
-    const float radius = HYPOT(r_X, r_Y),
+    const float radius = HYPOT(r_P, r_Q),
-                center_X = current_position[X_AXIS] - r_X,
+                center_P = current_position[p_axis] - r_P,
-                center_Y = current_position[Y_AXIS] - r_Y,
+                center_Q = current_position[q_axis] - r_Q,
-                rt_X = logical[X_AXIS] - center_X,
+                rt_X = logical[p_axis] - center_P,
-                rt_Y = logical[Y_AXIS] - center_Y,
+                rt_Y = logical[q_axis] - center_Q,
-                linear_travel = logical[Z_AXIS] - current_position[Z_AXIS],
+                linear_travel = logical[l_axis] - current_position[l_axis],
                 extruder_travel = logical[E_AXIS] - current_position[E_AXIS];
 
     // CCW angle of rotation between position and target from the circle center. Only one atan2() trig computation required.
-    float angular_travel = ATAN2(r_X * rt_Y - r_Y * rt_X, r_X * rt_X + r_Y * rt_Y);
+    float angular_travel = ATAN2(r_P * rt_Y - r_Q * rt_X, r_P * rt_X + r_Q * rt_Y);
     if (angular_travel < 0) angular_travel += RADIANS(360);
     if (clockwise) angular_travel -= RADIANS(360);
 
-    // Make a circle if the angular rotation is 0
+    // Make a circle if the angular rotation is 0 and the target is current position
-    if (angular_travel == 0 && current_position[X_AXIS] == logical[X_AXIS] && current_position[Y_AXIS] == logical[Y_AXIS])
+    if (angular_travel == 0 && current_position[p_axis] == logical[p_axis] && current_position[q_axis] == logical[q_axis])
-      angular_travel += RADIANS(360);
+      angular_travel = RADIANS(360);
 
     const float mm_of_travel = HYPOT(angular_travel * radius, FABS(linear_travel));
     if (mm_of_travel < 0.001) return;
@@ -11996,7 +12071,7 @@ void prepare_move_to_destination() {
                 cos_T = 1 - 0.5 * sq(theta_per_segment); // Small angle approximation
 
     // Initialize the linear axis
-    arc_target[Z_AXIS] = current_position[Z_AXIS];
+    arc_target[l_axis] = current_position[l_axis];
 
     // Initialize the extruder axis
     arc_target[E_AXIS] = current_position[E_AXIS];
@@ -12005,7 +12080,10 @@ void prepare_move_to_destination() {
 
     millis_t next_idle_ms = millis() + 200UL;
 
-    int8_t count = 0;
+    #if N_ARC_CORRECTION > 1
+      int8_t count = N_ARC_CORRECTION;
+    #endif
+
     for (uint16_t i = 1; i < segments; i++) { // Iterate (segments-1) times
 
       thermalManager.manage_heater();
@@ -12014,28 +12092,33 @@ void prepare_move_to_destination() {
         idle();
       }
 
-      if (++count < N_ARC_CORRECTION) {
+      #if N_ARC_CORRECTION > 1
-        // Apply vector rotation matrix to previous r_X / 1
+        if (--count) {
-        const float r_new_Y = r_X * sin_T + r_Y * cos_T;
+          // Apply vector rotation matrix to previous r_P / 1
-        r_X = r_X * cos_T - r_Y * sin_T;
+          const float r_new_Y = r_P * sin_T + r_Q * cos_T;
-        r_Y = r_new_Y;
+          r_P = r_P * cos_T - r_Q * sin_T;
+          r_Q = r_new_Y;
         }
-      else {
+        else
+      #endif
+      {
+        #if N_ARC_CORRECTION > 1
+          count = N_ARC_CORRECTION;
+        #endif
+
         // Arc correction to radius vector. Computed only every N_ARC_CORRECTION increments.
         // Compute exact location by applying transformation matrix from initial radius vector(=-offset).
         // To reduce stuttering, the sin and cos could be computed at different times.
         // For now, compute both at the same time.
-        const float cos_Ti = cos(i * theta_per_segment),
+        const float cos_Ti = cos(i * theta_per_segment), sin_Ti = sin(i * theta_per_segment);
-                    sin_Ti = sin(i * theta_per_segment);
+        r_P = -offset[0] * cos_Ti + offset[1] * sin_Ti;
-        r_X = -offset[X_AXIS] * cos_Ti + offset[Y_AXIS] * sin_Ti;
+        r_Q = -offset[0] * sin_Ti - offset[1] * cos_Ti;
-        r_Y = -offset[X_AXIS] * sin_Ti - offset[Y_AXIS] * cos_Ti;
-        count = 0;
       }
 
       // Update arc_target location
-      arc_target[X_AXIS] = center_X + r_X;
+      arc_target[p_axis] = center_P + r_P;
-      arc_target[Y_AXIS] = center_Y + r_Y;
+      arc_target[q_axis] = center_Q + r_Q;
-      arc_target[Z_AXIS] += linear_per_segment;
+      arc_target[l_axis] += linear_per_segment;
       arc_target[E_AXIS] += extruder_per_segment;
 
       clamp_to_software_endstops(arc_target);
@@ -12201,7 +12284,7 @@ void prepare_move_to_destination() {
       #endif
       HOTEND_LOOP()
         max_temp = MAX3(max_temp, thermalManager.degHotend(e), thermalManager.degTargetHotend(e));
-      bool new_led = (max_temp > 55.0) ? true : (max_temp < 54.0) ? false : red_led;
+      const bool new_led = (max_temp > 55.0) ? true : (max_temp < 54.0) ? false : red_led;
       if (new_led != red_led) {
         red_led = new_led;
         #if PIN_EXISTS(STAT_LED_RED)

Marlin/enum.h

@@ -167,12 +167,23 @@ enum LCDViewAction {
   LCDVIEW_CALL_NO_REDRAW
 };
 
+/**
+ * Dual X Carriage modes. A Dual Nozzle can also do duplication.
+ */
 #if ENABLED(DUAL_X_CARRIAGE) || ENABLED(DUAL_NOZZLE_DUPLICATION_MODE)
   enum DualXMode {
-    DXC_FULL_CONTROL_MODE,
+    DXC_FULL_CONTROL_MODE,  // DUAL_X_CARRIAGE only
-    DXC_AUTO_PARK_MODE,
+    DXC_AUTO_PARK_MODE,     // DUAL_X_CARRIAGE only
     DXC_DUPLICATION_MODE
   };
 #endif
 
+/**
+ * Workspace planes only apply to G2/G3 moves
+ * (and "canned cycles" - not a current feature)
+ */
+#if ENABLED(CNC_WORKSPACE_PLANES)
+  enum WorkspacePlane { PLANE_XY, PLANE_ZX, PLANE_YZ };
+#endif
+
 #endif // __ENUM_H__

Marlin/example_configurations/Cartesio/Configuration_adv.h

@@ -671,10 +671,16 @@
 
 // @section extras
 
-// Arc interpretation settings:
+//
-#define ARC_SUPPORT  // Disabling this saves ~2738 bytes
+// G2/G3 Arc Support
-#define MM_PER_ARC_SEGMENT 1
+//
-#define N_ARC_CORRECTION 25
+#define ARC_SUPPORT               // Disable this feature to save ~3226 bytes
+#if ENABLED(ARC_SUPPORT)
+  #define MM_PER_ARC_SEGMENT  1   // Length of each arc segment
+  #define N_ARC_CORRECTION   25   // Number of intertpolated segments between corrections
+  //#define ARC_P_CIRCLES         // Enable the 'P' parameter to specify complete circles
+  //#define CNC_WORKSPACE_PLANES  // Allow G2/G3 to operate in XY, ZX, or YZ planes
+#endif
 
 // Support for G5 with XYZE destination and IJPQ offsets. Requires ~2666 bytes.
 //#define BEZIER_CURVE_SUPPORT

Marlin/example_configurations/Felix/Configuration_adv.h

@@ -671,10 +671,16 @@
 
 // @section extras
 
-// Arc interpretation settings:
+//
-#define ARC_SUPPORT  // Disabling this saves ~2738 bytes
+// G2/G3 Arc Support
-#define MM_PER_ARC_SEGMENT 1
+//
-#define N_ARC_CORRECTION 25
+#define ARC_SUPPORT               // Disable this feature to save ~3226 bytes
+#if ENABLED(ARC_SUPPORT)
+  #define MM_PER_ARC_SEGMENT  1   // Length of each arc segment
+  #define N_ARC_CORRECTION   25   // Number of intertpolated segments between corrections
+  //#define ARC_P_CIRCLES         // Enable the 'P' parameter to specify complete circles
+  //#define CNC_WORKSPACE_PLANES  // Allow G2/G3 to operate in XY, ZX, or YZ planes
+#endif
 
 // Support for G5 with XYZE destination and IJPQ offsets. Requires ~2666 bytes.
 //#define BEZIER_CURVE_SUPPORT

Marlin/example_configurations/FolgerTech-i3-2020/Configuration_adv.h

@@ -678,10 +678,16 @@
 
 // @section extras
 
-// Arc interpretation settings:
+//
-#define ARC_SUPPORT  // Disabling this saves ~2738 bytes
+// G2/G3 Arc Support
-#define MM_PER_ARC_SEGMENT 1
+//
-#define N_ARC_CORRECTION 25
+#define ARC_SUPPORT               // Disable this feature to save ~3226 bytes
+#if ENABLED(ARC_SUPPORT)
+  #define MM_PER_ARC_SEGMENT  1   // Length of each arc segment
+  #define N_ARC_CORRECTION   25   // Number of intertpolated segments between corrections
+  //#define ARC_P_CIRCLES         // Enable the 'P' parameter to specify complete circles
+  //#define CNC_WORKSPACE_PLANES  // Allow G2/G3 to operate in XY, ZX, or YZ planes
+#endif
 
 // Support for G5 with XYZE destination and IJPQ offsets. Requires ~2666 bytes.
 //#define BEZIER_CURVE_SUPPORT

Marlin/example_configurations/Hephestos/Configuration_adv.h

@@ -671,10 +671,16 @@
 
 // @section extras
 
-// Arc interpretation settings:
+//
-#define ARC_SUPPORT  // Disabling this saves ~2738 bytes
+// G2/G3 Arc Support
-#define MM_PER_ARC_SEGMENT 1
+//
-#define N_ARC_CORRECTION 25
+#define ARC_SUPPORT               // Disable this feature to save ~3226 bytes
+#if ENABLED(ARC_SUPPORT)
+  #define MM_PER_ARC_SEGMENT  1   // Length of each arc segment
+  #define N_ARC_CORRECTION   25   // Number of intertpolated segments between corrections
+  //#define ARC_P_CIRCLES         // Enable the 'P' parameter to specify complete circles
+  //#define CNC_WORKSPACE_PLANES  // Allow G2/G3 to operate in XY, ZX, or YZ planes
+#endif
 
 // Support for G5 with XYZE destination and IJPQ offsets. Requires ~2666 bytes.
 //#define BEZIER_CURVE_SUPPORT

Marlin/example_configurations/Hephestos_2/Configuration_adv.h

@@ -654,10 +654,16 @@
 
 // @section extras
 
-// Arc interpretation settings:
+//
-#define ARC_SUPPORT  // Disabling this saves ~2738 bytes
+// G2/G3 Arc Support
-#define MM_PER_ARC_SEGMENT 1
+//
-#define N_ARC_CORRECTION 25
+#define ARC_SUPPORT               // Disable this feature to save ~3226 bytes
+#if ENABLED(ARC_SUPPORT)
+  #define MM_PER_ARC_SEGMENT  1   // Length of each arc segment
+  #define N_ARC_CORRECTION   25   // Number of intertpolated segments between corrections
+  //#define ARC_P_CIRCLES         // Enable the 'P' parameter to specify complete circles
+  //#define CNC_WORKSPACE_PLANES  // Allow G2/G3 to operate in XY, ZX, or YZ planes
+#endif
 
 // Support for G5 with XYZE destination and IJPQ offsets. Requires ~2666 bytes.
 //#define BEZIER_CURVE_SUPPORT

Marlin/example_configurations/K8200/Configuration_adv.h

@@ -684,10 +684,16 @@
 
 // @section extras
 
-// Arc interpretation settings:
+//
-#define ARC_SUPPORT  // Disabling this saves ~2738 bytes
+// G2/G3 Arc Support
-#define MM_PER_ARC_SEGMENT 1
+//
-#define N_ARC_CORRECTION 25
+#define ARC_SUPPORT               // Disable this feature to save ~3226 bytes
+#if ENABLED(ARC_SUPPORT)
+  #define MM_PER_ARC_SEGMENT  1   // Length of each arc segment
+  #define N_ARC_CORRECTION   25   // Number of intertpolated segments between corrections
+  //#define ARC_P_CIRCLES         // Enable the 'P' parameter to specify complete circles
+  //#define CNC_WORKSPACE_PLANES  // Allow G2/G3 to operate in XY, ZX, or YZ planes
+#endif
 
 // Support for G5 with XYZE destination and IJPQ offsets. Requires ~2666 bytes.
 //#define BEZIER_CURVE_SUPPORT

Marlin/example_configurations/K8400/Configuration_adv.h

@@ -671,10 +671,16 @@
 
 // @section extras
 
-// Arc interpretation settings:
+//
-#define ARC_SUPPORT  // Disabling this saves ~2738 bytes
+// G2/G3 Arc Support
-#define MM_PER_ARC_SEGMENT 1
+//
-#define N_ARC_CORRECTION 25
+#define ARC_SUPPORT               // Disable this feature to save ~3226 bytes
+#if ENABLED(ARC_SUPPORT)
+  #define MM_PER_ARC_SEGMENT  1   // Length of each arc segment
+  #define N_ARC_CORRECTION   25   // Number of intertpolated segments between corrections
+  //#define ARC_P_CIRCLES         // Enable the 'P' parameter to specify complete circles
+  //#define CNC_WORKSPACE_PLANES  // Allow G2/G3 to operate in XY, ZX, or YZ planes
+#endif
 
 // Support for G5 with XYZE destination and IJPQ offsets. Requires ~2666 bytes.
 //#define BEZIER_CURVE_SUPPORT

Marlin/example_configurations/M150/Configuration_adv.h

@@ -678,10 +678,16 @@
 
 // @section extras
 
-// Arc interpretation settings:
+//
-#define ARC_SUPPORT  // Disabling this saves ~2738 bytes
+// G2/G3 Arc Support
-#define MM_PER_ARC_SEGMENT 1
+//
-#define N_ARC_CORRECTION 25
+#define ARC_SUPPORT               // Disable this feature to save ~3226 bytes
+#if ENABLED(ARC_SUPPORT)
+  #define MM_PER_ARC_SEGMENT  1   // Length of each arc segment
+  #define N_ARC_CORRECTION   25   // Number of intertpolated segments between corrections
+  //#define ARC_P_CIRCLES         // Enable the 'P' parameter to specify complete circles
+  //#define CNC_WORKSPACE_PLANES  // Allow G2/G3 to operate in XY, ZX, or YZ planes
+#endif
 
 // Support for G5 with XYZE destination and IJPQ offsets. Requires ~2666 bytes.
 //#define BEZIER_CURVE_SUPPORT

Marlin/example_configurations/RigidBot/Configuration_adv.h

@@ -671,10 +671,16 @@
 
 // @section extras
 
-// Arc interpretation settings:
+//
-#define ARC_SUPPORT  // Disabling this saves ~2738 bytes
+// G2/G3 Arc Support
-#define MM_PER_ARC_SEGMENT 1
+//
-#define N_ARC_CORRECTION 25
+#define ARC_SUPPORT               // Disable this feature to save ~3226 bytes
+#if ENABLED(ARC_SUPPORT)
+  #define MM_PER_ARC_SEGMENT  1   // Length of each arc segment
+  #define N_ARC_CORRECTION   25   // Number of intertpolated segments between corrections
+  //#define ARC_P_CIRCLES         // Enable the 'P' parameter to specify complete circles
+  //#define CNC_WORKSPACE_PLANES  // Allow G2/G3 to operate in XY, ZX, or YZ planes
+#endif
 
 // Support for G5 with XYZE destination and IJPQ offsets. Requires ~2666 bytes.
 //#define BEZIER_CURVE_SUPPORT

Marlin/example_configurations/SCARA/Configuration_adv.h

@@ -671,10 +671,16 @@
 
 // @section extras
 
-// Arc interpretation settings:
+//
-#define ARC_SUPPORT  // Disabling this saves ~2738 bytes
+// G2/G3 Arc Support
-#define MM_PER_ARC_SEGMENT 1
+//
-#define N_ARC_CORRECTION 25
+#define ARC_SUPPORT               // Disable this feature to save ~3226 bytes
+#if ENABLED(ARC_SUPPORT)
+  #define MM_PER_ARC_SEGMENT  1   // Length of each arc segment
+  #define N_ARC_CORRECTION   25   // Number of intertpolated segments between corrections
+  //#define ARC_P_CIRCLES         // Enable the 'P' parameter to specify complete circles
+  //#define CNC_WORKSPACE_PLANES  // Allow G2/G3 to operate in XY, ZX, or YZ planes
+#endif
 
 // Support for G5 with XYZE destination and IJPQ offsets. Requires ~2666 bytes.
 //#define BEZIER_CURVE_SUPPORT

Marlin/example_configurations/TAZ4/Configuration_adv.h

@@ -671,10 +671,16 @@
 
 // @section extras
 
-// Arc interpretation settings:
+//
-#define ARC_SUPPORT  // Disabling this saves ~2738 bytes
+// G2/G3 Arc Support
-#define MM_PER_ARC_SEGMENT 1
+//
-#define N_ARC_CORRECTION 25
+#define ARC_SUPPORT               // Disable this feature to save ~3226 bytes
+#if ENABLED(ARC_SUPPORT)
+  #define MM_PER_ARC_SEGMENT  1   // Length of each arc segment
+  #define N_ARC_CORRECTION   25   // Number of intertpolated segments between corrections
+  //#define ARC_P_CIRCLES         // Enable the 'P' parameter to specify complete circles
+  //#define CNC_WORKSPACE_PLANES  // Allow G2/G3 to operate in XY, ZX, or YZ planes
+#endif
 
 // Support for G5 with XYZE destination and IJPQ offsets. Requires ~2666 bytes.
 //#define BEZIER_CURVE_SUPPORT

Marlin/example_configurations/TinyBoy2/Configuration_adv.h

@@ -674,10 +674,16 @@
 
 // @section extras
 
-// Arc interpretation settings:
+//
-#define ARC_SUPPORT  // Disabling this saves ~2738 bytes
+// G2/G3 Arc Support
-#define MM_PER_ARC_SEGMENT 1
+//
-#define N_ARC_CORRECTION 25
+#define ARC_SUPPORT               // Disable this feature to save ~3226 bytes
+#if ENABLED(ARC_SUPPORT)
+  #define MM_PER_ARC_SEGMENT  1   // Length of each arc segment
+  #define N_ARC_CORRECTION   25   // Number of intertpolated segments between corrections
+  //#define ARC_P_CIRCLES         // Enable the 'P' parameter to specify complete circles
+  //#define CNC_WORKSPACE_PLANES  // Allow G2/G3 to operate in XY, ZX, or YZ planes
+#endif
 
 // Support for G5 with XYZE destination and IJPQ offsets. Requires ~2666 bytes.
 //#define BEZIER_CURVE_SUPPORT

Marlin/example_configurations/WITBOX/Configuration_adv.h

@@ -671,10 +671,16 @@
 
 // @section extras
 
-// Arc interpretation settings:
+//
-#define ARC_SUPPORT  // Disabling this saves ~2738 bytes
+// G2/G3 Arc Support
-#define MM_PER_ARC_SEGMENT 1
+//
-#define N_ARC_CORRECTION 25
+#define ARC_SUPPORT               // Disable this feature to save ~3226 bytes
+#if ENABLED(ARC_SUPPORT)
+  #define MM_PER_ARC_SEGMENT  1   // Length of each arc segment
+  #define N_ARC_CORRECTION   25   // Number of intertpolated segments between corrections
+  //#define ARC_P_CIRCLES         // Enable the 'P' parameter to specify complete circles
+  //#define CNC_WORKSPACE_PLANES  // Allow G2/G3 to operate in XY, ZX, or YZ planes
+#endif
 
 // Support for G5 with XYZE destination and IJPQ offsets. Requires ~2666 bytes.
 //#define BEZIER_CURVE_SUPPORT

Marlin/example_configurations/delta/FLSUN/auto_calibrate/Configuration_adv.h

@@ -676,10 +676,16 @@
 
 // @section extras
 
-// Arc interpretation settings:
+//
-#define ARC_SUPPORT  // Disabling this saves ~2738 bytes
+// G2/G3 Arc Support
-#define MM_PER_ARC_SEGMENT 1
+//
-#define N_ARC_CORRECTION 25
+#define ARC_SUPPORT               // Disable this feature to save ~3226 bytes
+#if ENABLED(ARC_SUPPORT)
+  #define MM_PER_ARC_SEGMENT  1   // Length of each arc segment
+  #define N_ARC_CORRECTION   25   // Number of intertpolated segments between corrections
+  //#define ARC_P_CIRCLES         // Enable the 'P' parameter to specify complete circles
+  //#define CNC_WORKSPACE_PLANES  // Allow G2/G3 to operate in XY, ZX, or YZ planes
+#endif
 
 // Support for G5 with XYZE destination and IJPQ offsets. Requires ~2666 bytes.
 //#define BEZIER_CURVE_SUPPORT

Marlin/example_configurations/delta/FLSUN/kossel_mini/Configuration_adv.h

@@ -676,10 +676,16 @@
 
 // @section extras
 
-// Arc interpretation settings:
+//
-#define ARC_SUPPORT  // Disabling this saves ~2738 bytes
+// G2/G3 Arc Support
-#define MM_PER_ARC_SEGMENT 1
+//
-#define N_ARC_CORRECTION 25
+#define ARC_SUPPORT               // Disable this feature to save ~3226 bytes
+#if ENABLED(ARC_SUPPORT)
+  #define MM_PER_ARC_SEGMENT  1   // Length of each arc segment
+  #define N_ARC_CORRECTION   25   // Number of intertpolated segments between corrections
+  //#define ARC_P_CIRCLES         // Enable the 'P' parameter to specify complete circles
+  //#define CNC_WORKSPACE_PLANES  // Allow G2/G3 to operate in XY, ZX, or YZ planes
+#endif
 
 // Support for G5 with XYZE destination and IJPQ offsets. Requires ~2666 bytes.
 //#define BEZIER_CURVE_SUPPORT

Marlin/example_configurations/delta/generic/Configuration_adv.h

@@ -673,10 +673,16 @@
 
 // @section extras
 
-// Arc interpretation settings:
+//
-#define ARC_SUPPORT  // Disabling this saves ~2738 bytes
+// G2/G3 Arc Support
-#define MM_PER_ARC_SEGMENT 1
+//
-#define N_ARC_CORRECTION 25
+#define ARC_SUPPORT               // Disable this feature to save ~3226 bytes
+#if ENABLED(ARC_SUPPORT)
+  #define MM_PER_ARC_SEGMENT  1   // Length of each arc segment
+  #define N_ARC_CORRECTION   25   // Number of intertpolated segments between corrections
+  //#define ARC_P_CIRCLES         // Enable the 'P' parameter to specify complete circles
+  //#define CNC_WORKSPACE_PLANES  // Allow G2/G3 to operate in XY, ZX, or YZ planes
+#endif
 
 // Support for G5 with XYZE destination and IJPQ offsets. Requires ~2666 bytes.
 //#define BEZIER_CURVE_SUPPORT

Marlin/example_configurations/delta/kossel_mini/Configuration_adv.h

@@ -673,10 +673,16 @@
 
 // @section extras
 
-// Arc interpretation settings:
+//
-#define ARC_SUPPORT  // Disabling this saves ~2738 bytes
+// G2/G3 Arc Support
-#define MM_PER_ARC_SEGMENT 1
+//
-#define N_ARC_CORRECTION 25
+#define ARC_SUPPORT               // Disable this feature to save ~3226 bytes
+#if ENABLED(ARC_SUPPORT)
+  #define MM_PER_ARC_SEGMENT  1   // Length of each arc segment
+  #define N_ARC_CORRECTION   25   // Number of intertpolated segments between corrections
+  //#define ARC_P_CIRCLES         // Enable the 'P' parameter to specify complete circles
+  //#define CNC_WORKSPACE_PLANES  // Allow G2/G3 to operate in XY, ZX, or YZ planes
+#endif
 
 // Support for G5 with XYZE destination and IJPQ offsets. Requires ~2666 bytes.
 //#define BEZIER_CURVE_SUPPORT

Marlin/example_configurations/delta/kossel_pro/Configuration_adv.h

@@ -678,10 +678,16 @@
 
 // @section extras
 
-// Arc interpretation settings:
+//
-#define ARC_SUPPORT  // Disabling this saves ~2738 bytes
+// G2/G3 Arc Support
-#define MM_PER_ARC_SEGMENT 1
+//
-#define N_ARC_CORRECTION 25
+#define ARC_SUPPORT               // Disable this feature to save ~3226 bytes
+#if ENABLED(ARC_SUPPORT)
+  #define MM_PER_ARC_SEGMENT  1   // Length of each arc segment
+  #define N_ARC_CORRECTION   25   // Number of intertpolated segments between corrections
+  //#define ARC_P_CIRCLES         // Enable the 'P' parameter to specify complete circles
+  //#define CNC_WORKSPACE_PLANES  // Allow G2/G3 to operate in XY, ZX, or YZ planes
+#endif
 
 // Support for G5 with XYZE destination and IJPQ offsets. Requires ~2666 bytes.
 //#define BEZIER_CURVE_SUPPORT

Marlin/example_configurations/delta/kossel_xl/Configuration_adv.h

@@ -673,10 +673,16 @@
 
 // @section extras
 
-// Arc interpretation settings:
+//
-#define ARC_SUPPORT  // Disabling this saves ~2738 bytes
+// G2/G3 Arc Support
-#define MM_PER_ARC_SEGMENT 1
+//
-#define N_ARC_CORRECTION 25
+#define ARC_SUPPORT               // Disable this feature to save ~3226 bytes
+#if ENABLED(ARC_SUPPORT)
+  #define MM_PER_ARC_SEGMENT  1   // Length of each arc segment
+  #define N_ARC_CORRECTION   25   // Number of intertpolated segments between corrections
+  //#define ARC_P_CIRCLES         // Enable the 'P' parameter to specify complete circles
+  //#define CNC_WORKSPACE_PLANES  // Allow G2/G3 to operate in XY, ZX, or YZ planes
+#endif
 
 // Support for G5 with XYZE destination and IJPQ offsets. Requires ~2666 bytes.
 //#define BEZIER_CURVE_SUPPORT

Marlin/example_configurations/gCreate_gMax1.5+/Configuration_adv.h

@@ -678,10 +678,16 @@
 
 // @section extras
 
-// Arc interpretation settings:
+//
-#define ARC_SUPPORT  // Disabling this saves ~2738 bytes
+// G2/G3 Arc Support
-#define MM_PER_ARC_SEGMENT 1
+//
-#define N_ARC_CORRECTION 25
+#define ARC_SUPPORT               // Disable this feature to save ~3226 bytes
+#if ENABLED(ARC_SUPPORT)
+  #define MM_PER_ARC_SEGMENT  1   // Length of each arc segment
+  #define N_ARC_CORRECTION   25   // Number of intertpolated segments between corrections
+  //#define ARC_P_CIRCLES         // Enable the 'P' parameter to specify complete circles
+  //#define CNC_WORKSPACE_PLANES  // Allow G2/G3 to operate in XY, ZX, or YZ planes
+#endif
 
 // Support for G5 with XYZE destination and IJPQ offsets. Requires ~2666 bytes.
 //#define BEZIER_CURVE_SUPPORT

Marlin/example_configurations/makibox/Configuration_adv.h

@@ -671,10 +671,16 @@
 
 // @section extras
 
-// Arc interpretation settings:
+//
-#define ARC_SUPPORT  // Disabling this saves ~2738 bytes
+// G2/G3 Arc Support
-#define MM_PER_ARC_SEGMENT 1
+//
-#define N_ARC_CORRECTION 25
+#define ARC_SUPPORT               // Disable this feature to save ~3226 bytes
+#if ENABLED(ARC_SUPPORT)
+  #define MM_PER_ARC_SEGMENT  1   // Length of each arc segment
+  #define N_ARC_CORRECTION   25   // Number of intertpolated segments between corrections
+  //#define ARC_P_CIRCLES         // Enable the 'P' parameter to specify complete circles
+  //#define CNC_WORKSPACE_PLANES  // Allow G2/G3 to operate in XY, ZX, or YZ planes
+#endif
 
 // Support for G5 with XYZE destination and IJPQ offsets. Requires ~2666 bytes.
 //#define BEZIER_CURVE_SUPPORT

Marlin/example_configurations/tvrrug/Round2/Configuration_adv.h

@@ -671,10 +671,16 @@
 
 // @section extras
 
-// Arc interpretation settings:
+//
-#define ARC_SUPPORT  // Disabling this saves ~2738 bytes
+// G2/G3 Arc Support
-#define MM_PER_ARC_SEGMENT 1
+//
-#define N_ARC_CORRECTION 25
+#define ARC_SUPPORT               // Disable this feature to save ~3226 bytes
+#if ENABLED(ARC_SUPPORT)
+  #define MM_PER_ARC_SEGMENT  1   // Length of each arc segment
+  #define N_ARC_CORRECTION   25   // Number of intertpolated segments between corrections
+  //#define ARC_P_CIRCLES         // Enable the 'P' parameter to specify complete circles
+  //#define CNC_WORKSPACE_PLANES  // Allow G2/G3 to operate in XY, ZX, or YZ planes
+#endif
 
 // Support for G5 with XYZE destination and IJPQ offsets. Requires ~2666 bytes.
 //#define BEZIER_CURVE_SUPPORT

Marlin/example_configurations/wt150/Configuration_adv.h

@@ -674,10 +674,16 @@
 
 // @section extras
 
-// Arc interpretation settings:
+//
-#define ARC_SUPPORT  // Disabling this saves ~2738 bytes
+// G2/G3 Arc Support
-#define MM_PER_ARC_SEGMENT 1
+//
-#define N_ARC_CORRECTION 25
+#define ARC_SUPPORT               // Disable this feature to save ~3226 bytes
+#if ENABLED(ARC_SUPPORT)
+  #define MM_PER_ARC_SEGMENT  1   // Length of each arc segment
+  #define N_ARC_CORRECTION   25   // Number of intertpolated segments between corrections
+  //#define ARC_P_CIRCLES         // Enable the 'P' parameter to specify complete circles
+  //#define CNC_WORKSPACE_PLANES  // Allow G2/G3 to operate in XY, ZX, or YZ planes
+#endif
 
 // Support for G5 with XYZE destination and IJPQ offsets. Requires ~2666 bytes.
 //#define BEZIER_CURVE_SUPPORT

Marlin/pinsDebug.h

@@ -41,7 +41,7 @@ bool endstop_monitor_flag = false;
 
 // first pass - put the name strings into FLASH
 
-#define _ADD_PIN_2(PIN_NAME, ENTRY_NAME) static const unsigned char ENTRY_NAME[] PROGMEM = { PIN_NAME };
+#define _ADD_PIN_2(PIN_NAME, ENTRY_NAME) static const char ENTRY_NAME[] PROGMEM = { PIN_NAME };
 #define _ADD_PIN(PIN_NAME, COUNTER) _ADD_PIN_2(PIN_NAME, entry_NAME_##COUNTER)
 #define REPORT_NAME_DIGITAL(NAME, COUNTER) _ADD_PIN(#NAME, COUNTER)
 #define REPORT_NAME_ANALOG(NAME, COUNTER) _ADD_PIN(#NAME, COUNTER)
@@ -64,12 +64,18 @@ bool endstop_monitor_flag = false;
 #undef REPORT_NAME_DIGITAL
 #undef REPORT_NAME_ANALOG
 
-#define _ADD_PIN_2(ENTRY_NAME, NAME, IS_DIGITAL) { (const char*)ENTRY_NAME, (const char*)NAME, (const char*)IS_DIGITAL },
+#define _ADD_PIN_2(ENTRY_NAME, NAME, IS_DIGITAL) { ENTRY_NAME, NAME, IS_DIGITAL },
 #define _ADD_PIN(NAME, COUNTER, IS_DIGITAL) _ADD_PIN_2(entry_NAME_##COUNTER, NAME, IS_DIGITAL)
-#define REPORT_NAME_DIGITAL(NAME, COUNTER) _ADD_PIN(NAME, COUNTER, (uint8_t)1)
+#define REPORT_NAME_DIGITAL(NAME, COUNTER) _ADD_PIN(NAME, COUNTER, true)
-#define REPORT_NAME_ANALOG(NAME, COUNTER) _ADD_PIN(analogInputToDigitalPin(NAME), COUNTER, 0)
+#define REPORT_NAME_ANALOG(NAME, COUNTER) _ADD_PIN(analogInputToDigitalPin(NAME), COUNTER, false)
 
-const char* const pin_array[][3] PROGMEM = {
+typedef struct {
+  const char * const name;
+  uint8_t pin;
+  bool is_digital;
+} PinInfo;
+
+const PinInfo pin_array[] PROGMEM = {
 
   /**
    *  [pin name]  [pin number]  [is digital or analog]  1 = digital, 0 = analog
@@ -83,21 +89,19 @@ const char* const pin_array[][3] PROGMEM = {
   // manually add pins ...
   #if SERIAL_PORT == 0
     #if AVR_ATmega2560_FAMILY
-      { RXD_NAME, 0, 1 },
+      { RXD_NAME, 0, true },
-      { TXD_NAME, 1, 1 },
+      { TXD_NAME, 1, true },
     #elif AVR_ATmega1284_FAMILY
-      { RXD_NAME, 8, 1 },
+      { RXD_NAME, 8, true },
-      { TXD_NAME, 9, 1 },
+      { TXD_NAME, 9, true },
     #endif
   #endif
 
   #include "pinsDebug_list.h"
-  #line 96
+  #line 102
 
 };
 
-#define n_array (sizeof(pin_array) / sizeof(char*)) / 3
-
 #define AVR_ATmega2560_FAMILY_PLUS_70 (MOTHERBOARD == BOARD_BQ_ZUM_MEGA_3D \
 || MOTHERBOARD == BOARD_MIGHTYBOARD_REVE \
 || MOTHERBOARD == BOARD_MINIRAMBO \
@@ -439,12 +443,12 @@ static void print_input_or_output(const bool isout) {
 }
 
 // pretty report with PWM info
-inline void report_pin_state_extended(int8_t pin, bool ignore, bool extended = false,const char *start_string = "") {
+inline void report_pin_state_extended(int8_t pin, bool ignore, bool extended = false, const char *start_string = "") {
   uint8_t temp_char;
   char *name_mem_pointer, buffer[30];   // for the sprintf statements
   bool found = false, multi_name_pin = false;
-  for (uint8_t x = 0; x < n_array; x++)  {    // scan entire array and report all instances of this pin
+  for (uint8_t x = 0; x < COUNT(pin_array); x++)  {    // scan entire array and report all instances of this pin
-    if (pgm_read_byte(&pin_array[x][1]) == pin) {
+    if (pgm_read_byte(&pin_array[x].pin) == pin) {
       if (found) multi_name_pin = true;
       found = true;
       if (!multi_name_pin) {    // report digitial and analog pin number only on the first time through
@@ -461,7 +465,7 @@ inline void report_pin_state_extended(int8_t pin, bool ignore, bool extended = f
         SERIAL_CHAR('.');
         SERIAL_ECHO_SP(26 + strlen(start_string));  // add padding if not the first instance found
       }
-      name_mem_pointer = (char*)pgm_read_word(&pin_array[x][0]);
+      name_mem_pointer = (char*)pgm_read_word(&pin_array[x].name);
       for (uint8_t y = 0; y < 28; y++) {                   // always print pin name
         temp_char = pgm_read_byte(name_mem_pointer + y);
         if (temp_char != 0)
@@ -489,7 +493,7 @@ inline void report_pin_state_extended(int8_t pin, bool ignore, bool extended = f
             else
           #endif
           {
-            if (!(pgm_read_byte(&pin_array[x][2]))) {
+            if (!(pgm_read_byte(&pin_array[x].is_digital))) {
               sprintf_P(buffer, PSTR("Analog in = %5d"), analogRead(pin - analogInputToDigitalPin(0)));
               SERIAL_ECHO(buffer);
             }

Marlin/planner.cpp

@@ -1103,12 +1103,12 @@ void Planner::_buffer_line(const float &a, const float &b, const float &c, const
         while (filwidth_delay_dist >= MMD_MM) filwidth_delay_dist -= MMD_MM;
 
         // Convert into an index into the measurement array
-        filwidth_delay_index[0] = (int)(filwidth_delay_dist * 0.1 + 0.0001);
+        filwidth_delay_index[0] = int8_t(filwidth_delay_dist * 0.1);
 
         // If the index has changed (must have gone forward)...
         if (filwidth_delay_index[0] != filwidth_delay_index[1]) {
           filwidth_e_count = 0; // Reset the E movement counter
-          const int8_t meas_sample = thermalManager.widthFil_to_size_ratio() - 100; // Subtract 100 to reduce magnitude - to store in a signed char
+          const uint8_t meas_sample = thermalManager.widthFil_to_size_ratio() - 100; // Subtract 100 to reduce magnitude - to store in a signed char
           do {
             filwidth_delay_index[1] = (filwidth_delay_index[1] + 1) % MMD_CM; // The next unused slot
             measurement_delay[filwidth_delay_index[1]] = meas_sample;         // Store the measurement

Marlin/temperature.cpp

@@ -180,7 +180,7 @@ int16_t Temperature::minttemp_raw[HOTENDS] = ARRAY_BY_HOTENDS(HEATER_0_RAW_LO_TE
 #endif
 
 #if ENABLED(FILAMENT_WIDTH_SENSOR)
-  int16_t Temperature::meas_shift_index;  // Index of a delayed sample in buffer
+  int8_t Temperature::meas_shift_index;  // Index of a delayed sample in buffer
 #endif
 
 #if HAS_AUTO_FAN
@@ -196,7 +196,7 @@ uint8_t Temperature::soft_pwm_amount[HOTENDS],
 #endif
 
 #if ENABLED(FILAMENT_WIDTH_SENSOR)
-  int Temperature::current_raw_filwidth = 0;  //Holds measured filament diameter - one extruder only
+  uint16_t Temperature::current_raw_filwidth = 0; // Measured filament diameter - one extruder only
 #endif
 
 #if ENABLED(PROBING_HEATERS_OFF)
@@ -957,7 +957,7 @@ void Temperature::updateTemperaturesFromRawValues() {
 
   // Convert raw Filament Width to millimeters
   float Temperature::analog2widthFil() {
-    return current_raw_filwidth / 16383.0 * 5.0;
+    return current_raw_filwidth * 5.0 * (1.0 / 16383.0);
     //return current_raw_filwidth;
   }
 

Marlin/temperature.h

@@ -247,7 +247,7 @@ class Temperature {
     #endif
 
     #if ENABLED(FILAMENT_WIDTH_SENSOR)
-      static int16_t meas_shift_index;  // Index of a delayed sample in buffer
+      static int8_t meas_shift_index;  // Index of a delayed sample in buffer
     #endif
 
     #if HAS_AUTO_FAN
@@ -255,7 +255,7 @@ class Temperature {
     #endif
 
     #if ENABLED(FILAMENT_WIDTH_SENSOR)
-      static int current_raw_filwidth;  //Holds measured filament diameter - one extruder only
+      static uint16_t current_raw_filwidth; // Measured filament diameter - one extruder only
     #endif
 
     #if ENABLED(PROBING_HEATERS_OFF)

Marlin/ultralcd.cpp

@@ -4001,7 +4001,7 @@ void kill_screen(const char* lcd_msg) {
    *
    */
   #if ENABLED(REPRAPWORLD_KEYPAD)
-    void _reprapworld_keypad_move(AxisEnum axis, int16_t dir) {
+    void _reprapworld_keypad_move(const AxisEnum axis, const int16_t dir) {
       move_menu_scale = REPRAPWORLD_KEYPAD_MOVE_STEP;
       encoderPosition = dir;
       switch (axis) {