Merge pull request #7918 from thinkyhead/bf1_neopixel_full

[1.1.x] Different NEOPIXEL types
master
Scott Lahteine 7 years ago committed by GitHub
commit f054f566b4

@ -475,6 +475,6 @@
#define HAS_SOFTWARE_ENDSTOPS (ENABLED(MIN_SOFTWARE_ENDSTOPS) || ENABLED(MAX_SOFTWARE_ENDSTOPS))
#define HAS_RESUME_CONTINUE (ENABLED(NEWPANEL) || ENABLED(EMERGENCY_PARSER))
#define HAS_COLOR_LEDS (ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_RGBW_LED))
#define HAS_COLOR_LEDS (ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_LED))
#endif // CONDITIONALS_LCD_H

@ -1588,16 +1588,22 @@
* Adds the M150 command to set the LED (or LED strip) color.
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
* luminance values can be set from 0 to 255.
* For Neopixel LED overall brightness parameters is also available
*
* *** CAUTION ***
* LED Strips require a MOFSET Chip between PWM lines and LEDs,
* as the Arduino cannot handle the current the LEDs will require.
* Failure to follow this precaution can destroy your Arduino!
* The Neopixel LED is 5V powered, but linear 5V regulator on Arduino
* cannot handle such current, separate 5V power supply must be used
* *** CAUTION ***
*
* LED type. This options are mutualy exclusive. Uncomment only one.
*
*/
//#define RGB_LED
//#define RGBW_LED
#if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
#define RGB_LED_R_PIN 34
#define RGB_LED_G_PIN 43
@ -1606,10 +1612,13 @@
#endif
// Support for Adafruit Neopixel LED driver
//#define NEOPIXEL_RGBW_LED
#if ENABLED(NEOPIXEL_RGBW_LED)
#define NEOPIXEL_PIN 4 // D4 (EXP2-5 on Printrboard)
#define NEOPIXEL_PIXELS 3
//#define NEOPIXEL_LED
#if ENABLED(NEOPIXEL_LED)
#define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h)
#define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
#define NEOPIXEL_PIXELS 30 // Number of LEDs on strip
#define NEOPIXEL_IS_SEQUENTIAL // Sequent display for temperature change - LED by LED. Comment out for change all LED at time
#define NEOPIXEL_BRIGHTNESS 127 // Initial brightness 0-255
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
#endif
@ -1624,7 +1633,7 @@
* - Change to green once print has finished
* - Turn off after the print has finished and the user has pushed a button
*/
#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_RGBW_LED)
#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_LED)
#define PRINTER_EVENT_LEDS
#endif

@ -142,7 +142,7 @@
* M140 - Set bed target temp. S<temp>
* M145 - Set heatup values for materials on the LCD. H<hotend> B<bed> F<fan speed> for S<material> (0=PLA, 1=ABS)
* M149 - Set temperature units. (Requires TEMPERATURE_UNITS_SUPPORT)
* M150 - Set Status LED Color as R<red> U<green> B<blue>. Values 0-255. (Requires BLINKM, RGB_LED, RGBW_LED, or PCA9632)
* M150 - Set Status LED Color as R<red> U<green> B<blue> P<bright>. Values 0-255. (Requires BLINKM, RGB_LED, RGBW_LED, NEOPIXEL_LED, or PCA9632).
* M155 - Auto-report temperatures with interval of S<seconds>. (Requires AUTO_REPORT_TEMPERATURES)
* M163 - Set a single proportion for a mixing extruder. (Requires MIXING_EXTRUDER)
* M164 - Save the mix as a virtual extruder. (Requires MIXING_EXTRUDER and MIXING_VIRTUAL_TOOLS)
@ -283,7 +283,7 @@
#include "Max7219_Debug_LEDs.h"
#endif
#if ENABLED(NEOPIXEL_RGBW_LED)
#if ENABLED(NEOPIXEL_LED)
#include <Adafruit_NeoPixel.h>
#endif
@ -349,6 +349,20 @@
|| isnan(ubl.z_values[0][0]))
#endif
#if ENABLED(NEOPIXEL_LED)
#if NEOPIXEL_TYPE == NEO_RGB || NEOPIXEL_TYPE == NEO_RBG || NEOPIXEL_TYPE == NEO_GRB || NEOPIXEL_TYPE == NEO_GBR || NEOPIXEL_TYPE == NEO_BRG || NEOPIXEL_TYPE == NEO_BGR
#define NEO_WHITE 255, 255, 255
#else
#define NEO_WHITE 0, 0, 0, 255
#endif
#endif
#if ENABLED(RGB_LED) || ENABLED(BLINKM) || ENABLED(PCA9632)
#define LED_WHITE 255, 255, 255
#elif ENABLED(RGBW_LED)
#define LED_WHITE 0, 0, 0, 255
#endif
bool Running = true;
uint8_t marlin_debug_flags = DEBUG_NONE;
@ -978,9 +992,9 @@ void servo_init() {
#if HAS_COLOR_LEDS
#if ENABLED(NEOPIXEL_RGBW_LED)
#if ENABLED(NEOPIXEL_LED)
Adafruit_NeoPixel pixels(NEOPIXEL_PIXELS, NEOPIXEL_PIN, NEO_GRBW + NEO_KHZ800);
Adafruit_NeoPixel pixels(NEOPIXEL_PIXELS, NEOPIXEL_PIN, NEOPIXEL_TYPE + NEO_KHZ800);
void set_neopixel_color(const uint32_t color) {
for (uint16_t i = 0; i < pixels.numPixels(); ++i)
@ -989,7 +1003,7 @@ void servo_init() {
}
void setup_neopixel() {
pixels.setBrightness(255); // 0 - 255 range
pixels.setBrightness(NEOPIXEL_BRIGHTNESS); // 0 - 255 range
pixels.begin();
pixels.show(); // initialize to all off
@ -1002,26 +1016,28 @@ void servo_init() {
set_neopixel_color(pixels.Color(0, 0, 255, 0)); // blue
delay(2000);
#endif
set_neopixel_color(pixels.Color(0, 0, 0, 255)); // white
set_neopixel_color(pixels.Color(NEO_WHITE)); // white
}
#endif // NEOPIXEL_RGBW_LED
#endif // NEOPIXEL_LED
void set_led_color(
const uint8_t r, const uint8_t g, const uint8_t b
#if ENABLED(RGBW_LED) || ENABLED(NEOPIXEL_RGBW_LED)
#if ENABLED(RGBW_LED) || ENABLED(NEOPIXEL_LED)
, const uint8_t w = 0
#if ENABLED(NEOPIXEL_RGBW_LED)
#if ENABLED(NEOPIXEL_LED)
, const uint8_t p = NEOPIXEL_BRIGHTNESS
, bool isSequence = false
#endif
#endif
) {
#if ENABLED(NEOPIXEL_RGBW_LED)
#if ENABLED(NEOPIXEL_LED)
const uint32_t color = pixels.Color(r, g, b, w);
static uint16_t nextLed = 0;
pixels.setBrightness(p);
if (!isSequence)
set_neopixel_color(color);
else {
@ -7590,8 +7606,12 @@ inline void gcode_M109() {
if (blue != old_blue) {
old_blue = blue;
set_led_color(255, 0, blue
#if ENABLED(NEOPIXEL_RGBW_LED)
, 0, true
#if ENABLED(NEOPIXEL_LED)
, 0
, pixels.getBrightness()
#if ENABLED(NEOPIXEL_IS_SEQUENTIAL)
, true
#endif
#endif
);
}
@ -7629,10 +7649,11 @@ inline void gcode_M109() {
if (wait_for_heatup) {
LCD_MESSAGEPGM(MSG_HEATING_COMPLETE);
#if ENABLED(PRINTER_EVENT_LEDS)
#if ENABLED(RGBW_LED) || ENABLED(NEOPIXEL_RGBW_LED)
set_led_color(0, 0, 0, 255); // Turn on the WHITE LED
#else
set_led_color(255, 255, 255); // Set LEDs All On
#if ENABLED(RGB_LED) || ENABLED(BLINKM) || ENABLED(PCA9632) || ENABLED(RGBW_LED)
set_led_color(LED_WHITE);
#endif
#if ENABLED(NEOPIXEL_LED)
set_neopixel_color(pixels.Color(NEO_WHITE));
#endif
#endif
}
@ -7730,8 +7751,11 @@ inline void gcode_M109() {
if (red != old_red) {
old_red = red;
set_led_color(red, 0, 255
#if ENABLED(NEOPIXEL_RGBW_LED)
, 0, true
#if ENABLED(NEOPIXEL_LED)
, 0, pixels.getBrightness()
#if ENABLED(NEOPIXEL_IS_SEQUENTIAL)
, true
#endif
#endif
);
}
@ -8378,8 +8402,10 @@ inline void gcode_M121() { endstops.enable_globally(false); }
/**
* M150: Set Status LED Color - Use R-U-B-W for R-G-B-W
* and Brightness - Use P (for NEOPIXEL only)
*
* Always sets all 3 or 4 components. If a component is left out, set to 0.
* If brightness is left out, no value changed
*
* Examples:
*
@ -8388,15 +8414,19 @@ inline void gcode_M121() { endstops.enable_globally(false); }
* M150 ; Turn LED off
* M150 R U B ; Turn LED white
* M150 W ; Turn LED white using a white LED
*
* M150 P127 ; Set LED 50% brightness
* M150 P ; Set LED full brightness
*/
inline void gcode_M150() {
set_led_color(
parser.seen('R') ? (parser.has_value() ? parser.value_byte() : 255) : 0,
parser.seen('U') ? (parser.has_value() ? parser.value_byte() : 255) : 0,
parser.seen('B') ? (parser.has_value() ? parser.value_byte() : 255) : 0
#if ENABLED(RGBW_LED) || ENABLED(NEOPIXEL_RGBW_LED)
#if ENABLED(RGBW_LED) || ENABLED(NEOPIXEL_LED)
, parser.seen('W') ? (parser.has_value() ? parser.value_byte() : 255) : 0
#if ENABLED(NEOPIXEL_LED)
, parser.seen('P') ? (parser.has_value() ? parser.value_byte() : 255) : pixels.getBrightness()
#endif
#endif
);
}
@ -13492,7 +13522,7 @@ void setup() {
OUT_WRITE(STAT_LED_BLUE_PIN, LOW); // turn it off
#endif
#if ENABLED(NEOPIXEL_RGBW_LED)
#if ENABLED(NEOPIXEL_LED)
SET_OUTPUT(NEOPIXEL_PIN);
setup_neopixel();
#endif

@ -210,6 +210,8 @@
#error "MIN_RETRACT is now MIN_AUTORETRACT and MAX_AUTORETRACT. Please update your Configuration_adv.h."
#elif defined(ADVANCE)
#error "ADVANCE was removed in Marlin 1.1.6. Please use LIN_ADVANCE."
#elif defined(NEOPIXEL_RGBW_LED)
#error "NEOPIXEL_RGBW_LED is now NEOPIXEL_LED. Please update your configuration."
#endif
/**
@ -1099,12 +1101,12 @@ static_assert(1 >= 0
#if !(_RGB_TEST && PIN_EXISTS(RGB_LED_W))
#error "RGBW_LED requires RGB_LED_R_PIN, RGB_LED_G_PIN, RGB_LED_B_PIN, and RGB_LED_W_PIN."
#endif
#elif ENABLED(NEOPIXEL_RGBW_LED)
#elif ENABLED(NEOPIXEL_LED)
#if !(PIN_EXISTS(NEOPIXEL) && NEOPIXEL_PIXELS > 0)
#error "NEOPIXEL_RGBW_LED requires NEOPIXEL_PIN and NEOPIXEL_PIXELS."
#error "NEOPIXEL_LED requires NEOPIXEL_PIN and NEOPIXEL_PIXELS."
#endif
#elif ENABLED(PRINTER_EVENT_LEDS) && DISABLED(BLINKM) && DISABLED(PCA9632) && DISABLED(NEOPIXEL_RGBW_LED)
#error "PRINTER_EVENT_LEDS requires BLINKM, PCA9632, RGB_LED, RGBW_LED or NEOPIXEL_RGBW_LED."
#elif ENABLED(PRINTER_EVENT_LEDS) && DISABLED(BLINKM) && DISABLED(PCA9632) && DISABLED(NEOPIXEL_LED)
#error "PRINTER_EVENT_LEDS requires BLINKM, PCA9632, RGB_LED, RGBW_LED or NEOPIXEL_LED."
#endif
/**

@ -1608,16 +1608,22 @@
* Adds the M150 command to set the LED (or LED strip) color.
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
* luminance values can be set from 0 to 255.
* For Neopixel LED overall brightness parameters is also available
*
* *** CAUTION ***
* LED Strips require a MOFSET Chip between PWM lines and LEDs,
* as the Arduino cannot handle the current the LEDs will require.
* Failure to follow this precaution can destroy your Arduino!
* The Neopixel LED is 5V powered, but linear 5V regulator on Arduino
* cannot handle such current, separate 5V power supply must be used
* *** CAUTION ***
*
* LED type. This options are mutualy exclusive. Uncomment only one.
*
*/
//#define RGB_LED
//#define RGBW_LED
#if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
#define RGB_LED_R_PIN 34
#define RGB_LED_G_PIN 43
@ -1626,10 +1632,13 @@
#endif
// Support for Adafruit Neopixel LED driver
//#define NEOPIXEL_RGBW_LED
#if ENABLED(NEOPIXEL_RGBW_LED)
#define NEOPIXEL_PIN 4 // D4 (EXP2-5 on Printrboard)
#define NEOPIXEL_PIXELS 3
//#define NEOPIXEL_LED
#if ENABLED(NEOPIXEL_LED)
#define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h)
#define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
#define NEOPIXEL_PIXELS 30 // Number of LEDs on strip
#define NEOPIXEL_IS_SEQUENTIAL // Sequent display for temperature change - LED by LED. Comment out for change all LED at time
#define NEOPIXEL_BRIGHTNESS 127 // Initial brightness 0-255
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
#endif

@ -1588,16 +1588,22 @@
* Adds the M150 command to set the LED (or LED strip) color.
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
* luminance values can be set from 0 to 255.
* For Neopixel LED overall brightness parameters is also available
*
* *** CAUTION ***
* LED Strips require a MOFSET Chip between PWM lines and LEDs,
* as the Arduino cannot handle the current the LEDs will require.
* Failure to follow this precaution can destroy your Arduino!
* The Neopixel LED is 5V powered, but linear 5V regulator on Arduino
* cannot handle such current, separate 5V power supply must be used
* *** CAUTION ***
*
* LED type. This options are mutualy exclusive. Uncomment only one.
*
*/
//#define RGB_LED
//#define RGBW_LED
#if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
#define RGB_LED_R_PIN 34
#define RGB_LED_G_PIN 43
@ -1606,10 +1612,13 @@
#endif
// Support for Adafruit Neopixel LED driver
//#define NEOPIXEL_RGBW_LED
#if ENABLED(NEOPIXEL_RGBW_LED)
#define NEOPIXEL_PIN 4 // D4 (EXP2-5 on Printrboard)
#define NEOPIXEL_PIXELS 3
//#define NEOPIXEL_LED
#if ENABLED(NEOPIXEL_LED)
#define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h)
#define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
#define NEOPIXEL_PIXELS 30 // Number of LEDs on strip
#define NEOPIXEL_IS_SEQUENTIAL // Sequent display for temperature change - LED by LED. Comment out for change all LED at time
#define NEOPIXEL_BRIGHTNESS 127 // Initial brightness 0-255
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
#endif

@ -1747,16 +1747,22 @@
* Adds the M150 command to set the LED (or LED strip) color.
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
* luminance values can be set from 0 to 255.
* For Neopixel LED overall brightness parameters is also available
*
* *** CAUTION ***
* LED Strips require a MOFSET Chip between PWM lines and LEDs,
* as the Arduino cannot handle the current the LEDs will require.
* Failure to follow this precaution can destroy your Arduino!
* The Neopixel LED is 5V powered, but linear 5V regulator on Arduino
* cannot handle such current, separate 5V power supply must be used
* *** CAUTION ***
*
* LED type. This options are mutualy exclusive. Uncomment only one.
*
*/
//#define RGB_LED
//#define RGBW_LED
#if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
#define RGB_LED_R_PIN 34
#define RGB_LED_G_PIN 43
@ -1765,10 +1771,13 @@
#endif
// Support for Adafruit Neopixel LED driver
//#define NEOPIXEL_RGBW_LED
#if ENABLED(NEOPIXEL_RGBW_LED)
#define NEOPIXEL_PIN 4 // D4 (EXP2-5 on Printrboard)
#define NEOPIXEL_PIXELS 3
//#define NEOPIXEL_LED
#if ENABLED(NEOPIXEL_LED)
#define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h)
#define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
#define NEOPIXEL_PIXELS 30 // Number of LEDs on strip
#define NEOPIXEL_IS_SEQUENTIAL // Sequent display for temperature change - LED by LED. Comment out for change all LED at time
#define NEOPIXEL_BRIGHTNESS 127 // Initial brightness 0-255
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
#endif

@ -1596,16 +1596,22 @@
* Adds the M150 command to set the LED (or LED strip) color.
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
* luminance values can be set from 0 to 255.
* For Neopixel LED overall brightness parameters is also available
*
* *** CAUTION ***
* LED Strips require a MOFSET Chip between PWM lines and LEDs,
* as the Arduino cannot handle the current the LEDs will require.
* Failure to follow this precaution can destroy your Arduino!
* The Neopixel LED is 5V powered, but linear 5V regulator on Arduino
* cannot handle such current, separate 5V power supply must be used
* *** CAUTION ***
*
* LED type. This options are mutualy exclusive. Uncomment only one.
*
*/
//#define RGB_LED
//#define RGBW_LED
#if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
#define RGB_LED_R_PIN 34
#define RGB_LED_G_PIN 43
@ -1614,10 +1620,13 @@
#endif
// Support for Adafruit Neopixel LED driver
//#define NEOPIXEL_RGBW_LED
#if ENABLED(NEOPIXEL_RGBW_LED)
#define NEOPIXEL_PIN 4 // D4 (EXP2-5 on Printrboard)
#define NEOPIXEL_PIXELS 3
//#define NEOPIXEL_LED
#if ENABLED(NEOPIXEL_LED)
#define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h)
#define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
#define NEOPIXEL_PIXELS 30 // Number of LEDs on strip
#define NEOPIXEL_IS_SEQUENTIAL // Sequent display for temperature change - LED by LED. Comment out for change all LED at time
#define NEOPIXEL_BRIGHTNESS 127 // Initial brightness 0-255
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
#endif

@ -1579,16 +1579,22 @@
* Adds the M150 command to set the LED (or LED strip) color.
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
* luminance values can be set from 0 to 255.
* For Neopixel LED overall brightness parameters is also available
*
* *** CAUTION ***
* LED Strips require a MOFSET Chip between PWM lines and LEDs,
* as the Arduino cannot handle the current the LEDs will require.
* Failure to follow this precaution can destroy your Arduino!
* The Neopixel LED is 5V powered, but linear 5V regulator on Arduino
* cannot handle such current, separate 5V power supply must be used
* *** CAUTION ***
*
* LED type. This options are mutualy exclusive. Uncomment only one.
*
*/
//#define RGB_LED
//#define RGBW_LED
#if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
#define RGB_LED_R_PIN 34
#define RGB_LED_G_PIN 43
@ -1597,10 +1603,13 @@
#endif
// Support for Adafruit Neopixel LED driver
//#define NEOPIXEL_RGBW_LED
#if ENABLED(NEOPIXEL_RGBW_LED)
#define NEOPIXEL_PIN 4 // D4 (EXP2-5 on Printrboard)
#define NEOPIXEL_PIXELS 3
//#define NEOPIXEL_LED
#if ENABLED(NEOPIXEL_LED)
#define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h)
#define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
#define NEOPIXEL_PIXELS 30 // Number of LEDs on strip
#define NEOPIXEL_IS_SEQUENTIAL // Sequent display for temperature change - LED by LED. Comment out for change all LED at time
#define NEOPIXEL_BRIGHTNESS 127 // Initial brightness 0-255
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
#endif

@ -1589,16 +1589,22 @@
* Adds the M150 command to set the LED (or LED strip) color.
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
* luminance values can be set from 0 to 255.
* For Neopixel LED overall brightness parameters is also available
*
* *** CAUTION ***
* LED Strips require a MOFSET Chip between PWM lines and LEDs,
* as the Arduino cannot handle the current the LEDs will require.
* Failure to follow this precaution can destroy your Arduino!
* The Neopixel LED is 5V powered, but linear 5V regulator on Arduino
* cannot handle such current, separate 5V power supply must be used
* *** CAUTION ***
*
* LED type. This options are mutualy exclusive. Uncomment only one.
*
*/
//#define RGB_LED
//#define RGBW_LED
#if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
#define RGB_LED_R_PIN 34
#define RGB_LED_G_PIN 43
@ -1607,10 +1613,13 @@
#endif
// Support for Adafruit Neopixel LED driver
//#define NEOPIXEL_RGBW_LED
#if ENABLED(NEOPIXEL_RGBW_LED)
#define NEOPIXEL_PIN 4 // D4 (EXP2-5 on Printrboard)
#define NEOPIXEL_PIXELS 3
//#define NEOPIXEL_LED
#if ENABLED(NEOPIXEL_LED)
#define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h)
#define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
#define NEOPIXEL_PIXELS 30 // Number of LEDs on strip
#define NEOPIXEL_IS_SEQUENTIAL // Sequent display for temperature change - LED by LED. Comment out for change all LED at time
#define NEOPIXEL_BRIGHTNESS 127 // Initial brightness 0-255
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
#endif

@ -1579,16 +1579,22 @@
* Adds the M150 command to set the LED (or LED strip) color.
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
* luminance values can be set from 0 to 255.
* For Neopixel LED overall brightness parameters is also available
*
* *** CAUTION ***
* LED Strips require a MOFSET Chip between PWM lines and LEDs,
* as the Arduino cannot handle the current the LEDs will require.
* Failure to follow this precaution can destroy your Arduino!
* The Neopixel LED is 5V powered, but linear 5V regulator on Arduino
* cannot handle such current, separate 5V power supply must be used
* *** CAUTION ***
*
* LED type. This options are mutualy exclusive. Uncomment only one.
*
*/
//#define RGB_LED
//#define RGBW_LED
#if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
#define RGB_LED_R_PIN 34
#define RGB_LED_G_PIN 43
@ -1597,10 +1603,13 @@
#endif
// Support for Adafruit Neopixel LED driver
//#define NEOPIXEL_RGBW_LED
#if ENABLED(NEOPIXEL_RGBW_LED)
#define NEOPIXEL_PIN 4 // D4 (EXP2-5 on Printrboard)
#define NEOPIXEL_PIXELS 3
//#define NEOPIXEL_LED
#if ENABLED(NEOPIXEL_LED)
#define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h)
#define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
#define NEOPIXEL_PIXELS 30 // Number of LEDs on strip
#define NEOPIXEL_IS_SEQUENTIAL // Sequent display for temperature change - LED by LED. Comment out for change all LED at time
#define NEOPIXEL_BRIGHTNESS 127 // Initial brightness 0-255
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
#endif

@ -1587,16 +1587,22 @@
* Adds the M150 command to set the LED (or LED strip) color.
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
* luminance values can be set from 0 to 255.
* For Neopixel LED overall brightness parameters is also available
*
* *** CAUTION ***
* LED Strips require a MOFSET Chip between PWM lines and LEDs,
* as the Arduino cannot handle the current the LEDs will require.
* Failure to follow this precaution can destroy your Arduino!
* The Neopixel LED is 5V powered, but linear 5V regulator on Arduino
* cannot handle such current, separate 5V power supply must be used
* *** CAUTION ***
*
* LED type. This options are mutualy exclusive. Uncomment only one.
*
*/
//#define RGB_LED
//#define RGBW_LED
#if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
#define RGB_LED_R_PIN 34
#define RGB_LED_G_PIN 43
@ -1605,10 +1611,13 @@
#endif
// Support for Adafruit Neopixel LED driver
//#define NEOPIXEL_RGBW_LED
#if ENABLED(NEOPIXEL_RGBW_LED)
#define NEOPIXEL_PIN 4 // D4 (EXP2-5 on Printrboard)
#define NEOPIXEL_PIXELS 3
//#define NEOPIXEL_LED
#if ENABLED(NEOPIXEL_LED)
#define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h)
#define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
#define NEOPIXEL_PIXELS 30 // Number of LEDs on strip
#define NEOPIXEL_IS_SEQUENTIAL // Sequent display for temperature change - LED by LED. Comment out for change all LED at time
#define NEOPIXEL_BRIGHTNESS 127 // Initial brightness 0-255
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
#endif

@ -1598,16 +1598,22 @@
* Adds the M150 command to set the LED (or LED strip) color.
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
* luminance values can be set from 0 to 255.
* For Neopixel LED overall brightness parameters is also available
*
* *** CAUTION ***
* LED Strips require a MOFSET Chip between PWM lines and LEDs,
* as the Arduino cannot handle the current the LEDs will require.
* Failure to follow this precaution can destroy your Arduino!
* The Neopixel LED is 5V powered, but linear 5V regulator on Arduino
* cannot handle such current, separate 5V power supply must be used
* *** CAUTION ***
*
* LED type. This options are mutualy exclusive. Uncomment only one.
*
*/
//#define RGB_LED
//#define RGBW_LED
#if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
#define RGB_LED_R_PIN 34
#define RGB_LED_G_PIN 43
@ -1616,10 +1622,13 @@
#endif
// Support for Adafruit Neopixel LED driver
//#define NEOPIXEL_RGBW_LED
#if ENABLED(NEOPIXEL_RGBW_LED)
#define NEOPIXEL_PIN 4 // D4 (EXP2-5 on Printrboard)
#define NEOPIXEL_PIXELS 3
//#define NEOPIXEL_LED
#if ENABLED(NEOPIXEL_LED)
#define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h)
#define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
#define NEOPIXEL_PIXELS 30 // Number of LEDs on strip
#define NEOPIXEL_IS_SEQUENTIAL // Sequent display for temperature change - LED by LED. Comment out for change all LED at time
#define NEOPIXEL_BRIGHTNESS 127 // Initial brightness 0-255
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
#endif

@ -1570,16 +1570,22 @@
* Adds the M150 command to set the LED (or LED strip) color.
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
* luminance values can be set from 0 to 255.
* For Neopixel LED overall brightness parameters is also available
*
* *** CAUTION ***
* LED Strips require a MOFSET Chip between PWM lines and LEDs,
* as the Arduino cannot handle the current the LEDs will require.
* Failure to follow this precaution can destroy your Arduino!
* The Neopixel LED is 5V powered, but linear 5V regulator on Arduino
* cannot handle such current, separate 5V power supply must be used
* *** CAUTION ***
*
* LED type. This options are mutualy exclusive. Uncomment only one.
*
*/
//#define RGB_LED
//#define RGBW_LED
#if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
#define RGB_LED_R_PIN 34
#define RGB_LED_G_PIN 43
@ -1588,10 +1594,13 @@
#endif
// Support for Adafruit Neopixel LED driver
//#define NEOPIXEL_RGBW_LED
#if ENABLED(NEOPIXEL_RGBW_LED)
#define NEOPIXEL_PIN 4 // D4 (EXP2-5 on Printrboard)
#define NEOPIXEL_PIXELS 3
//#define NEOPIXEL_LED
#if ENABLED(NEOPIXEL_LED)
#define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h)
#define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
#define NEOPIXEL_PIXELS 30 // Number of LEDs on strip
#define NEOPIXEL_IS_SEQUENTIAL // Sequent display for temperature change - LED by LED. Comment out for change all LED at time
#define NEOPIXEL_BRIGHTNESS 127 // Initial brightness 0-255
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
#endif

@ -1570,16 +1570,22 @@
* Adds the M150 command to set the LED (or LED strip) color.
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
* luminance values can be set from 0 to 255.
* For Neopixel LED overall brightness parameters is also available
*
* *** CAUTION ***
* LED Strips require a MOFSET Chip between PWM lines and LEDs,
* as the Arduino cannot handle the current the LEDs will require.
* Failure to follow this precaution can destroy your Arduino!
* The Neopixel LED is 5V powered, but linear 5V regulator on Arduino
* cannot handle such current, separate 5V power supply must be used
* *** CAUTION ***
*
* LED type. This options are mutualy exclusive. Uncomment only one.
*
*/
//#define RGB_LED
//#define RGBW_LED
#if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
#define RGB_LED_R_PIN 34
#define RGB_LED_G_PIN 43
@ -1588,10 +1594,13 @@
#endif
// Support for Adafruit Neopixel LED driver
//#define NEOPIXEL_RGBW_LED
#if ENABLED(NEOPIXEL_RGBW_LED)
#define NEOPIXEL_PIN 4 // D4 (EXP2-5 on Printrboard)
#define NEOPIXEL_PIXELS 3
//#define NEOPIXEL_LED
#if ENABLED(NEOPIXEL_LED)
#define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h)
#define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
#define NEOPIXEL_PIXELS 30 // Number of LEDs on strip
#define NEOPIXEL_IS_SEQUENTIAL // Sequent display for temperature change - LED by LED. Comment out for change all LED at time
#define NEOPIXEL_BRIGHTNESS 127 // Initial brightness 0-255
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
#endif

@ -1593,16 +1593,22 @@
* Adds the M150 command to set the LED (or LED strip) color.
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
* luminance values can be set from 0 to 255.
* For Neopixel LED overall brightness parameters is also available
*
* *** CAUTION ***
* LED Strips require a MOFSET Chip between PWM lines and LEDs,
* as the Arduino cannot handle the current the LEDs will require.
* Failure to follow this precaution can destroy your Arduino!
* The Neopixel LED is 5V powered, but linear 5V regulator on Arduino
* cannot handle such current, separate 5V power supply must be used
* *** CAUTION ***
*
* LED type. This options are mutualy exclusive. Uncomment only one.
*
*/
//#define RGB_LED
//#define RGBW_LED
#if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
#define RGB_LED_R_PIN 34
#define RGB_LED_G_PIN 43
@ -1611,10 +1617,13 @@
#endif
// Support for Adafruit Neopixel LED driver
//#define NEOPIXEL_RGBW_LED
#if ENABLED(NEOPIXEL_RGBW_LED)
#define NEOPIXEL_PIN 4 // D4 (EXP2-5 on Printrboard)
#define NEOPIXEL_PIXELS 3
//#define NEOPIXEL_LED
#if ENABLED(NEOPIXEL_LED)
#define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h)
#define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
#define NEOPIXEL_PIXELS 30 // Number of LEDs on strip
#define NEOPIXEL_IS_SEQUENTIAL // Sequent display for temperature change - LED by LED. Comment out for change all LED at time
#define NEOPIXEL_BRIGHTNESS 127 // Initial brightness 0-255
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
#endif

@ -1603,16 +1603,22 @@
* Adds the M150 command to set the LED (or LED strip) color.
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
* luminance values can be set from 0 to 255.
* For Neopixel LED overall brightness parameters is also available
*
* *** CAUTION ***
* LED Strips require a MOFSET Chip between PWM lines and LEDs,
* as the Arduino cannot handle the current the LEDs will require.
* Failure to follow this precaution can destroy your Arduino!
* The Neopixel LED is 5V powered, but linear 5V regulator on Arduino
* cannot handle such current, separate 5V power supply must be used
* *** CAUTION ***
*
* LED type. This options are mutualy exclusive. Uncomment only one.
*
*/
//#define RGB_LED
//#define RGBW_LED
#if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
#define RGB_LED_R_PIN 34
#define RGB_LED_G_PIN 43
@ -1621,10 +1627,13 @@
#endif
// Support for Adafruit Neopixel LED driver
//#define NEOPIXEL_RGBW_LED
#if ENABLED(NEOPIXEL_RGBW_LED)
#define NEOPIXEL_PIN 4 // D4 (EXP2-5 on Printrboard)
#define NEOPIXEL_PIXELS 3
//#define NEOPIXEL_LED
#if ENABLED(NEOPIXEL_LED)
#define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h)
#define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
#define NEOPIXEL_PIXELS 30 // Number of LEDs on strip
#define NEOPIXEL_IS_SEQUENTIAL // Sequent display for temperature change - LED by LED. Comment out for change all LED at time
#define NEOPIXEL_BRIGHTNESS 127 // Initial brightness 0-255
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
#endif

@ -1588,16 +1588,22 @@
* Adds the M150 command to set the LED (or LED strip) color.
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
* luminance values can be set from 0 to 255.
* For Neopixel LED overall brightness parameters is also available
*
* *** CAUTION ***
* LED Strips require a MOFSET Chip between PWM lines and LEDs,
* as the Arduino cannot handle the current the LEDs will require.
* Failure to follow this precaution can destroy your Arduino!
* The Neopixel LED is 5V powered, but linear 5V regulator on Arduino
* cannot handle such current, separate 5V power supply must be used
* *** CAUTION ***
*
* LED type. This options are mutualy exclusive. Uncomment only one.
*
*/
//#define RGB_LED
//#define RGBW_LED
#if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
#define RGB_LED_R_PIN 34
#define RGB_LED_G_PIN 43
@ -1606,10 +1612,13 @@
#endif
// Support for Adafruit Neopixel LED driver
//#define NEOPIXEL_RGBW_LED
#if ENABLED(NEOPIXEL_RGBW_LED)
#define NEOPIXEL_PIN 4 // D4 (EXP2-5 on Printrboard)
#define NEOPIXEL_PIXELS 3
//#define NEOPIXEL_LED
#if ENABLED(NEOPIXEL_LED)
#define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h)
#define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
#define NEOPIXEL_PIXELS 30 // Number of LEDs on strip
#define NEOPIXEL_IS_SEQUENTIAL // Sequent display for temperature change - LED by LED. Comment out for change all LED at time
#define NEOPIXEL_BRIGHTNESS 127 // Initial brightness 0-255
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
#endif

@ -1592,16 +1592,22 @@
* Adds the M150 command to set the LED (or LED strip) color.
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
* luminance values can be set from 0 to 255.
* For Neopixel LED overall brightness parameters is also available
*
* *** CAUTION ***
* LED Strips require a MOFSET Chip between PWM lines and LEDs,
* as the Arduino cannot handle the current the LEDs will require.
* Failure to follow this precaution can destroy your Arduino!
* The Neopixel LED is 5V powered, but linear 5V regulator on Arduino
* cannot handle such current, separate 5V power supply must be used
* *** CAUTION ***
*
* LED type. This options are mutualy exclusive. Uncomment only one.
*
*/
//#define RGB_LED
//#define RGBW_LED
#if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
#define RGB_LED_R_PIN 34
#define RGB_LED_G_PIN 43
@ -1610,10 +1616,13 @@
#endif
// Support for Adafruit Neopixel LED driver
//#define NEOPIXEL_RGBW_LED
#if ENABLED(NEOPIXEL_RGBW_LED)
#define NEOPIXEL_PIN 4 // D4 (EXP2-5 on Printrboard)
#define NEOPIXEL_PIXELS 3
//#define NEOPIXEL_LED
#if ENABLED(NEOPIXEL_LED)
#define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h)
#define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
#define NEOPIXEL_PIXELS 30 // Number of LEDs on strip
#define NEOPIXEL_IS_SEQUENTIAL // Sequent display for temperature change - LED by LED. Comment out for change all LED at time
#define NEOPIXEL_BRIGHTNESS 127 // Initial brightness 0-255
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
#endif

@ -1616,16 +1616,22 @@
* Adds the M150 command to set the LED (or LED strip) color.
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
* luminance values can be set from 0 to 255.
* For Neopixel LED overall brightness parameters is also available
*
* *** CAUTION ***
* LED Strips require a MOFSET Chip between PWM lines and LEDs,
* as the Arduino cannot handle the current the LEDs will require.
* Failure to follow this precaution can destroy your Arduino!
* The Neopixel LED is 5V powered, but linear 5V regulator on Arduino
* cannot handle such current, separate 5V power supply must be used
* *** CAUTION ***
*
* LED type. This options are mutualy exclusive. Uncomment only one.
*
*/
//#define RGB_LED
//#define RGBW_LED
#if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
#define RGB_LED_R_PIN 34
#define RGB_LED_G_PIN 43
@ -1634,10 +1640,13 @@
#endif
// Support for Adafruit Neopixel LED driver
//#define NEOPIXEL_RGBW_LED
#if ENABLED(NEOPIXEL_RGBW_LED)
#define NEOPIXEL_PIN 4 // D4 (EXP2-5 on Printrboard)
#define NEOPIXEL_PIXELS 3
//#define NEOPIXEL_LED
#if ENABLED(NEOPIXEL_LED)
#define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h)
#define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
#define NEOPIXEL_PIXELS 30 // Number of LEDs on strip
#define NEOPIXEL_IS_SEQUENTIAL // Sequent display for temperature change - LED by LED. Comment out for change all LED at time
#define NEOPIXEL_BRIGHTNESS 127 // Initial brightness 0-255
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
#endif

@ -1588,16 +1588,22 @@
* Adds the M150 command to set the LED (or LED strip) color.
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
* luminance values can be set from 0 to 255.
* For Neopixel LED overall brightness parameters is also available
*
* *** CAUTION ***
* LED Strips require a MOFSET Chip between PWM lines and LEDs,
* as the Arduino cannot handle the current the LEDs will require.
* Failure to follow this precaution can destroy your Arduino!
* The Neopixel LED is 5V powered, but linear 5V regulator on Arduino
* cannot handle such current, separate 5V power supply must be used
* *** CAUTION ***
*
* LED type. This options are mutualy exclusive. Uncomment only one.
*
*/
//#define RGB_LED
//#define RGBW_LED
#if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
#define RGB_LED_R_PIN 34
#define RGB_LED_G_PIN 43
@ -1606,10 +1612,13 @@
#endif
// Support for Adafruit Neopixel LED driver
//#define NEOPIXEL_RGBW_LED
#if ENABLED(NEOPIXEL_RGBW_LED)
#define NEOPIXEL_PIN 4 // D4 (EXP2-5 on Printrboard)
#define NEOPIXEL_PIXELS 3
//#define NEOPIXEL_LED
#if ENABLED(NEOPIXEL_LED)
#define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h)
#define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
#define NEOPIXEL_PIXELS 30 // Number of LEDs on strip
#define NEOPIXEL_IS_SEQUENTIAL // Sequent display for temperature change - LED by LED. Comment out for change all LED at time
#define NEOPIXEL_BRIGHTNESS 127 // Initial brightness 0-255
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
#endif

@ -1588,16 +1588,22 @@
* Adds the M150 command to set the LED (or LED strip) color.
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
* luminance values can be set from 0 to 255.
* For Neopixel LED overall brightness parameters is also available
*
* *** CAUTION ***
* LED Strips require a MOFSET Chip between PWM lines and LEDs,
* as the Arduino cannot handle the current the LEDs will require.
* Failure to follow this precaution can destroy your Arduino!
* The Neopixel LED is 5V powered, but linear 5V regulator on Arduino
* cannot handle such current, separate 5V power supply must be used
* *** CAUTION ***
*
* LED type. This options are mutualy exclusive. Uncomment only one.
*
*/
//#define RGB_LED
//#define RGBW_LED
#if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
#define RGB_LED_R_PIN 34
#define RGB_LED_G_PIN 43
@ -1606,10 +1612,13 @@
#endif
// Support for Adafruit Neopixel LED driver
//#define NEOPIXEL_RGBW_LED
#if ENABLED(NEOPIXEL_RGBW_LED)
#define NEOPIXEL_PIN 4 // D4 (EXP2-5 on Printrboard)
#define NEOPIXEL_PIXELS 3
//#define NEOPIXEL_LED
#if ENABLED(NEOPIXEL_LED)
#define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h)
#define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
#define NEOPIXEL_PIXELS 30 // Number of LEDs on strip
#define NEOPIXEL_IS_SEQUENTIAL // Sequent display for temperature change - LED by LED. Comment out for change all LED at time
#define NEOPIXEL_BRIGHTNESS 127 // Initial brightness 0-255
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
#endif

@ -1600,16 +1600,22 @@
* Adds the M150 command to set the LED (or LED strip) color.
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
* luminance values can be set from 0 to 255.
* For Neopixel LED overall brightness parameters is also available
*
* *** CAUTION ***
* LED Strips require a MOFSET Chip between PWM lines and LEDs,
* as the Arduino cannot handle the current the LEDs will require.
* Failure to follow this precaution can destroy your Arduino!
* The Neopixel LED is 5V powered, but linear 5V regulator on Arduino
* cannot handle such current, separate 5V power supply must be used
* *** CAUTION ***
*
* LED type. This options are mutualy exclusive. Uncomment only one.
*
*/
//#define RGB_LED
//#define RGBW_LED
#if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
#define RGB_LED_R_PIN 34
#define RGB_LED_G_PIN 43
@ -1618,10 +1624,13 @@
#endif
// Support for Adafruit Neopixel LED driver
//#define NEOPIXEL_RGBW_LED
#if ENABLED(NEOPIXEL_RGBW_LED)
#define NEOPIXEL_PIN 4 // D4 (EXP2-5 on Printrboard)
#define NEOPIXEL_PIXELS 3
//#define NEOPIXEL_LED
#if ENABLED(NEOPIXEL_LED)
#define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h)
#define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
#define NEOPIXEL_PIXELS 30 // Number of LEDs on strip
#define NEOPIXEL_IS_SEQUENTIAL // Sequent display for temperature change - LED by LED. Comment out for change all LED at time
#define NEOPIXEL_BRIGHTNESS 127 // Initial brightness 0-255
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
#endif

@ -1619,16 +1619,22 @@
* Adds the M150 command to set the LED (or LED strip) color.
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
* luminance values can be set from 0 to 255.
* For Neopixel LED overall brightness parameters is also available
*
* *** CAUTION ***
* LED Strips require a MOFSET Chip between PWM lines and LEDs,
* as the Arduino cannot handle the current the LEDs will require.
* Failure to follow this precaution can destroy your Arduino!
* The Neopixel LED is 5V powered, but linear 5V regulator on Arduino
* cannot handle such current, separate 5V power supply must be used
* *** CAUTION ***
*
* LED type. This options are mutualy exclusive. Uncomment only one.
*
*/
#define RGB_LED
//#define RGBW_LED
#if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
#define RGB_LED_R_PIN 11
#define RGB_LED_G_PIN 10
@ -1637,10 +1643,13 @@
#endif
// Support for Adafruit Neopixel LED driver
//#define NEOPIXEL_RGBW_LED
#if ENABLED(NEOPIXEL_RGBW_LED)
#define NEOPIXEL_PIN 4 // D4 (EXP2-5 on Printrboard)
#define NEOPIXEL_PIXELS 3
//#define NEOPIXEL_LED
#if ENABLED(NEOPIXEL_LED)
#define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h)
#define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
#define NEOPIXEL_PIXELS 30 // Number of LEDs on strip
#define NEOPIXEL_IS_SEQUENTIAL // Sequent display for temperature change - LED by LED. Comment out for change all LED at time
#define NEOPIXEL_BRIGHTNESS 127 // Initial brightness 0-255
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
#endif

@ -1644,16 +1644,22 @@
* Adds the M150 command to set the LED (or LED strip) color.
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
* luminance values can be set from 0 to 255.
* For Neopixel LED overall brightness parameters is also available
*
* *** CAUTION ***
* LED Strips require a MOFSET Chip between PWM lines and LEDs,
* as the Arduino cannot handle the current the LEDs will require.
* Failure to follow this precaution can destroy your Arduino!
* The Neopixel LED is 5V powered, but linear 5V regulator on Arduino
* cannot handle such current, separate 5V power supply must be used
* *** CAUTION ***
*
* LED type. This options are mutualy exclusive. Uncomment only one.
*
*/
//#define RGB_LED
//#define RGBW_LED
#if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
#define RGB_LED_R_PIN 34
#define RGB_LED_G_PIN 43
@ -1662,10 +1668,13 @@
#endif
// Support for Adafruit Neopixel LED driver
//#define NEOPIXEL_RGBW_LED
#if ENABLED(NEOPIXEL_RGBW_LED)
#define NEOPIXEL_PIN 4 // D4 (EXP2-5 on Printrboard)
#define NEOPIXEL_PIXELS 3
//#define NEOPIXEL_LED
#if ENABLED(NEOPIXEL_LED)
#define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h)
#define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
#define NEOPIXEL_PIXELS 30 // Number of LEDs on strip
#define NEOPIXEL_IS_SEQUENTIAL // Sequent display for temperature change - LED by LED. Comment out for change all LED at time
#define NEOPIXEL_BRIGHTNESS 127 // Initial brightness 0-255
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
#endif

@ -1623,16 +1623,22 @@
* Adds the M150 command to set the LED (or LED strip) color.
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
* luminance values can be set from 0 to 255.
* For Neopixel LED overall brightness parameters is also available
*
* *** CAUTION ***
* LED Strips require a MOFSET Chip between PWM lines and LEDs,
* as the Arduino cannot handle the current the LEDs will require.
* Failure to follow this precaution can destroy your Arduino!
* The Neopixel LED is 5V powered, but linear 5V regulator on Arduino
* cannot handle such current, separate 5V power supply must be used
* *** CAUTION ***
*
* LED type. This options are mutualy exclusive. Uncomment only one.
*
*/
//#define RGB_LED
//#define RGBW_LED
#if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
#define RGB_LED_R_PIN 34
#define RGB_LED_G_PIN 43
@ -1641,10 +1647,13 @@
#endif
// Support for Adafruit Neopixel LED driver
//#define NEOPIXEL_RGBW_LED
#if ENABLED(NEOPIXEL_RGBW_LED)
#define NEOPIXEL_PIN 4 // D4 (EXP2-5 on Printrboard)
#define NEOPIXEL_PIXELS 3
//#define NEOPIXEL_LED
#if ENABLED(NEOPIXEL_LED)
#define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h)
#define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
#define NEOPIXEL_PIXELS 30 // Number of LEDs on strip
#define NEOPIXEL_IS_SEQUENTIAL // Sequent display for temperature change - LED by LED. Comment out for change all LED at time
#define NEOPIXEL_BRIGHTNESS 127 // Initial brightness 0-255
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
#endif

@ -1588,16 +1588,22 @@
* Adds the M150 command to set the LED (or LED strip) color.
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
* luminance values can be set from 0 to 255.
* For Neopixel LED overall brightness parameters is also available
*
* *** CAUTION ***
* LED Strips require a MOFSET Chip between PWM lines and LEDs,
* as the Arduino cannot handle the current the LEDs will require.
* Failure to follow this precaution can destroy your Arduino!
* The Neopixel LED is 5V powered, but linear 5V regulator on Arduino
* cannot handle such current, separate 5V power supply must be used
* *** CAUTION ***
*
* LED type. This options are mutualy exclusive. Uncomment only one.
*
*/
//#define RGB_LED
//#define RGBW_LED
#if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
#define RGB_LED_R_PIN 34
#define RGB_LED_G_PIN 43
@ -1606,10 +1612,13 @@
#endif
// Support for Adafruit Neopixel LED driver
//#define NEOPIXEL_RGBW_LED
#if ENABLED(NEOPIXEL_RGBW_LED)
#define NEOPIXEL_PIN 4 // D4 (EXP2-5 on Printrboard)
#define NEOPIXEL_PIXELS 3
//#define NEOPIXEL_LED
#if ENABLED(NEOPIXEL_LED)
#define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h)
#define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
#define NEOPIXEL_PIXELS 30 // Number of LEDs on strip
#define NEOPIXEL_IS_SEQUENTIAL // Sequent display for temperature change - LED by LED. Comment out for change all LED at time
#define NEOPIXEL_BRIGHTNESS 127 // Initial brightness 0-255
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
#endif

@ -1588,16 +1588,22 @@
* Adds the M150 command to set the LED (or LED strip) color.
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
* luminance values can be set from 0 to 255.
* For Neopixel LED overall brightness parameters is also available
*
* *** CAUTION ***
* LED Strips require a MOFSET Chip between PWM lines and LEDs,
* as the Arduino cannot handle the current the LEDs will require.
* Failure to follow this precaution can destroy your Arduino!
* The Neopixel LED is 5V powered, but linear 5V regulator on Arduino
* cannot handle such current, separate 5V power supply must be used
* *** CAUTION ***
*
* LED type. This options are mutualy exclusive. Uncomment only one.
*
*/
//#define RGB_LED
//#define RGBW_LED
#if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
#define RGB_LED_R_PIN 34
#define RGB_LED_G_PIN 43
@ -1606,10 +1612,13 @@
#endif
// Support for Adafruit Neopixel LED driver
//#define NEOPIXEL_RGBW_LED
#if ENABLED(NEOPIXEL_RGBW_LED)
#define NEOPIXEL_PIN 4 // D4 (EXP2-5 on Printrboard)
#define NEOPIXEL_PIXELS 3
//#define NEOPIXEL_LED
#if ENABLED(NEOPIXEL_LED)
#define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h)
#define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
#define NEOPIXEL_PIXELS 30 // Number of LEDs on strip
#define NEOPIXEL_IS_SEQUENTIAL // Sequent display for temperature change - LED by LED. Comment out for change all LED at time
#define NEOPIXEL_BRIGHTNESS 127 // Initial brightness 0-255
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
#endif

@ -1588,16 +1588,22 @@
* Adds the M150 command to set the LED (or LED strip) color.
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
* luminance values can be set from 0 to 255.
* For Neopixel LED overall brightness parameters is also available
*
* *** CAUTION ***
* LED Strips require a MOFSET Chip between PWM lines and LEDs,
* as the Arduino cannot handle the current the LEDs will require.
* Failure to follow this precaution can destroy your Arduino!
* The Neopixel LED is 5V powered, but linear 5V regulator on Arduino
* cannot handle such current, separate 5V power supply must be used
* *** CAUTION ***
*
* LED type. This options are mutualy exclusive. Uncomment only one.
*
*/
//#define RGB_LED
//#define RGBW_LED
#if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
#define RGB_LED_R_PIN 34
#define RGB_LED_G_PIN 43
@ -1606,10 +1612,13 @@
#endif
// Support for Adafruit Neopixel LED driver
//#define NEOPIXEL_RGBW_LED
#if ENABLED(NEOPIXEL_RGBW_LED)
#define NEOPIXEL_PIN 4 // D4 (EXP2-5 on Printrboard)
#define NEOPIXEL_PIXELS 3
//#define NEOPIXEL_LED
#if ENABLED(NEOPIXEL_LED)
#define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h)
#define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
#define NEOPIXEL_PIXELS 30 // Number of LEDs on strip
#define NEOPIXEL_IS_SEQUENTIAL // Sequent display for temperature change - LED by LED. Comment out for change all LED at time
#define NEOPIXEL_BRIGHTNESS 127 // Initial brightness 0-255
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
#endif

@ -1716,16 +1716,22 @@
* Adds the M150 command to set the LED (or LED strip) color.
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
* luminance values can be set from 0 to 255.
* For Neopixel LED overall brightness parameters is also available
*
* *** CAUTION ***
* LED Strips require a MOFSET Chip between PWM lines and LEDs,
* as the Arduino cannot handle the current the LEDs will require.
* Failure to follow this precaution can destroy your Arduino!
* The Neopixel LED is 5V powered, but linear 5V regulator on Arduino
* cannot handle such current, separate 5V power supply must be used
* *** CAUTION ***
*
* LED type. This options are mutualy exclusive. Uncomment only one.
*
*/
//#define RGB_LED
//#define RGBW_LED
#if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
#define RGB_LED_R_PIN 34
#define RGB_LED_G_PIN 43
@ -1734,10 +1740,13 @@
#endif
// Support for Adafruit Neopixel LED driver
//#define NEOPIXEL_RGBW_LED
#if ENABLED(NEOPIXEL_RGBW_LED)
#define NEOPIXEL_PIN 4 // D4 (EXP2-5 on Printrboard)
#define NEOPIXEL_PIXELS 3
//#define NEOPIXEL_LED
#if ENABLED(NEOPIXEL_LED)
#define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h)
#define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
#define NEOPIXEL_PIXELS 30 // Number of LEDs on strip
#define NEOPIXEL_IS_SEQUENTIAL // Sequent display for temperature change - LED by LED. Comment out for change all LED at time
#define NEOPIXEL_BRIGHTNESS 127 // Initial brightness 0-255
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
#endif

@ -1709,16 +1709,22 @@
* Adds the M150 command to set the LED (or LED strip) color.
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
* luminance values can be set from 0 to 255.
* For Neopixel LED overall brightness parameters is also available
*
* *** CAUTION ***
* LED Strips require a MOFSET Chip between PWM lines and LEDs,
* as the Arduino cannot handle the current the LEDs will require.
* Failure to follow this precaution can destroy your Arduino!
* The Neopixel LED is 5V powered, but linear 5V regulator on Arduino
* cannot handle such current, separate 5V power supply must be used
* *** CAUTION ***
*
* LED type. This options are mutualy exclusive. Uncomment only one.
*
*/
//#define RGB_LED
//#define RGBW_LED
#if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
#define RGB_LED_R_PIN 34
#define RGB_LED_G_PIN 43
@ -1727,10 +1733,13 @@
#endif
// Support for Adafruit Neopixel LED driver
//#define NEOPIXEL_RGBW_LED
#if ENABLED(NEOPIXEL_RGBW_LED)
#define NEOPIXEL_PIN 4 // D4 (EXP2-5 on Printrboard)
#define NEOPIXEL_PIXELS 3
//#define NEOPIXEL_LED
#if ENABLED(NEOPIXEL_LED)
#define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h)
#define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
#define NEOPIXEL_PIXELS 30 // Number of LEDs on strip
#define NEOPIXEL_IS_SEQUENTIAL // Sequent display for temperature change - LED by LED. Comment out for change all LED at time
#define NEOPIXEL_BRIGHTNESS 127 // Initial brightness 0-255
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
#endif

@ -1704,16 +1704,22 @@
* Adds the M150 command to set the LED (or LED strip) color.
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
* luminance values can be set from 0 to 255.
* For Neopixel LED overall brightness parameters is also available
*
* *** CAUTION ***
* LED Strips require a MOFSET Chip between PWM lines and LEDs,
* as the Arduino cannot handle the current the LEDs will require.
* Failure to follow this precaution can destroy your Arduino!
* The Neopixel LED is 5V powered, but linear 5V regulator on Arduino
* cannot handle such current, separate 5V power supply must be used
* *** CAUTION ***
*
* LED type. This options are mutualy exclusive. Uncomment only one.
*
*/
//#define RGB_LED
//#define RGBW_LED
#if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
#define RGB_LED_R_PIN 34
#define RGB_LED_G_PIN 43
@ -1722,10 +1728,13 @@
#endif
// Support for Adafruit Neopixel LED driver
//#define NEOPIXEL_RGBW_LED
#if ENABLED(NEOPIXEL_RGBW_LED)
#define NEOPIXEL_PIN 4 // D4 (EXP2-5 on Printrboard)
#define NEOPIXEL_PIXELS 3
//#define NEOPIXEL_LED
#if ENABLED(NEOPIXEL_LED)
#define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h)
#define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
#define NEOPIXEL_PIXELS 30 // Number of LEDs on strip
#define NEOPIXEL_IS_SEQUENTIAL // Sequent display for temperature change - LED by LED. Comment out for change all LED at time
#define NEOPIXEL_BRIGHTNESS 127 // Initial brightness 0-255
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
#endif

@ -1707,16 +1707,22 @@
* Adds the M150 command to set the LED (or LED strip) color.
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
* luminance values can be set from 0 to 255.
* For Neopixel LED overall brightness parameters is also available
*
* *** CAUTION ***
* LED Strips require a MOFSET Chip between PWM lines and LEDs,
* as the Arduino cannot handle the current the LEDs will require.
* Failure to follow this precaution can destroy your Arduino!
* The Neopixel LED is 5V powered, but linear 5V regulator on Arduino
* cannot handle such current, separate 5V power supply must be used
* *** CAUTION ***
*
* LED type. This options are mutualy exclusive. Uncomment only one.
*
*/
//#define RGB_LED
//#define RGBW_LED
#if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
#define RGB_LED_R_PIN 34
#define RGB_LED_G_PIN 43
@ -1725,10 +1731,13 @@
#endif
// Support for Adafruit Neopixel LED driver
//#define NEOPIXEL_RGBW_LED
#if ENABLED(NEOPIXEL_RGBW_LED)
#define NEOPIXEL_PIN 4 // D4 (EXP2-5 on Printrboard)
#define NEOPIXEL_PIXELS 3
//#define NEOPIXEL_LED
#if ENABLED(NEOPIXEL_LED)
#define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h)
#define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
#define NEOPIXEL_PIXELS 30 // Number of LEDs on strip
#define NEOPIXEL_IS_SEQUENTIAL // Sequent display for temperature change - LED by LED. Comment out for change all LED at time
#define NEOPIXEL_BRIGHTNESS 127 // Initial brightness 0-255
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
#endif

@ -1707,16 +1707,22 @@
* Adds the M150 command to set the LED (or LED strip) color.
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
* luminance values can be set from 0 to 255.
* For Neopixel LED overall brightness parameters is also available
*
* *** CAUTION ***
* LED Strips require a MOFSET Chip between PWM lines and LEDs,
* as the Arduino cannot handle the current the LEDs will require.
* Failure to follow this precaution can destroy your Arduino!
* The Neopixel LED is 5V powered, but linear 5V regulator on Arduino
* cannot handle such current, separate 5V power supply must be used
* *** CAUTION ***
*
* LED type. This options are mutualy exclusive. Uncomment only one.
*
*/
//#define RGB_LED
//#define RGBW_LED
#if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
#define RGB_LED_R_PIN 34
#define RGB_LED_G_PIN 43
@ -1725,10 +1731,13 @@
#endif
// Support for Adafruit Neopixel LED driver
//#define NEOPIXEL_RGBW_LED
#if ENABLED(NEOPIXEL_RGBW_LED)
#define NEOPIXEL_PIN 4 // D4 (EXP2-5 on Printrboard)
#define NEOPIXEL_PIXELS 3
//#define NEOPIXEL_LED
#if ENABLED(NEOPIXEL_LED)
#define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h)
#define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
#define NEOPIXEL_PIXELS 30 // Number of LEDs on strip
#define NEOPIXEL_IS_SEQUENTIAL // Sequent display for temperature change - LED by LED. Comment out for change all LED at time
#define NEOPIXEL_BRIGHTNESS 127 // Initial brightness 0-255
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
#endif

@ -1716,16 +1716,22 @@
* Adds the M150 command to set the LED (or LED strip) color.
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
* luminance values can be set from 0 to 255.
* For Neopixel LED overall brightness parameters is also available
*
* *** CAUTION ***
* LED Strips require a MOFSET Chip between PWM lines and LEDs,
* as the Arduino cannot handle the current the LEDs will require.
* Failure to follow this precaution can destroy your Arduino!
* The Neopixel LED is 5V powered, but linear 5V regulator on Arduino
* cannot handle such current, separate 5V power supply must be used
* *** CAUTION ***
*
* LED type. This options are mutualy exclusive. Uncomment only one.
*
*/
//#define RGB_LED
//#define RGBW_LED
#if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
#define RGB_LED_R_PIN 34
#define RGB_LED_G_PIN 43
@ -1734,10 +1740,13 @@
#endif
// Support for Adafruit Neopixel LED driver
//#define NEOPIXEL_RGBW_LED
#if ENABLED(NEOPIXEL_RGBW_LED)
#define NEOPIXEL_PIN 4 // D4 (EXP2-5 on Printrboard)
#define NEOPIXEL_PIXELS 3
//#define NEOPIXEL_LED
#if ENABLED(NEOPIXEL_LED)
#define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h)
#define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
#define NEOPIXEL_PIXELS 30 // Number of LEDs on strip
#define NEOPIXEL_IS_SEQUENTIAL // Sequent display for temperature change - LED by LED. Comment out for change all LED at time
#define NEOPIXEL_BRIGHTNESS 127 // Initial brightness 0-255
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
#endif

@ -1602,16 +1602,22 @@
* Adds the M150 command to set the LED (or LED strip) color.
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
* luminance values can be set from 0 to 255.
* For Neopixel LED overall brightness parameters is also available
*
* *** CAUTION ***
* LED Strips require a MOFSET Chip between PWM lines and LEDs,
* as the Arduino cannot handle the current the LEDs will require.
* Failure to follow this precaution can destroy your Arduino!
* The Neopixel LED is 5V powered, but linear 5V regulator on Arduino
* cannot handle such current, separate 5V power supply must be used
* *** CAUTION ***
*
* LED type. This options are mutualy exclusive. Uncomment only one.
*
*/
//#define RGB_LED
//#define RGBW_LED
#if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
#define RGB_LED_R_PIN 34
#define RGB_LED_G_PIN 43
@ -1620,10 +1626,13 @@
#endif
// Support for Adafruit Neopixel LED driver
//#define NEOPIXEL_RGBW_LED
#if ENABLED(NEOPIXEL_RGBW_LED)
#define NEOPIXEL_PIN 4 // D4 (EXP2-5 on Printrboard)
#define NEOPIXEL_PIXELS 3
//#define NEOPIXEL_LED
#if ENABLED(NEOPIXEL_LED)
#define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h)
#define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
#define NEOPIXEL_PIXELS 30 // Number of LEDs on strip
#define NEOPIXEL_IS_SEQUENTIAL // Sequent display for temperature change - LED by LED. Comment out for change all LED at time
#define NEOPIXEL_BRIGHTNESS 127 // Initial brightness 0-255
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
#endif

@ -1591,16 +1591,22 @@
* Adds the M150 command to set the LED (or LED strip) color.
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
* luminance values can be set from 0 to 255.
* For Neopixel LED overall brightness parameters is also available
*
* *** CAUTION ***
* LED Strips require a MOFSET Chip between PWM lines and LEDs,
* as the Arduino cannot handle the current the LEDs will require.
* Failure to follow this precaution can destroy your Arduino!
* The Neopixel LED is 5V powered, but linear 5V regulator on Arduino
* cannot handle such current, separate 5V power supply must be used
* *** CAUTION ***
*
* LED type. This options are mutualy exclusive. Uncomment only one.
*
*/
//#define RGB_LED
//#define RGBW_LED
#if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
#define RGB_LED_R_PIN 34
#define RGB_LED_G_PIN 43
@ -1609,10 +1615,13 @@
#endif
// Support for Adafruit Neopixel LED driver
//#define NEOPIXEL_RGBW_LED
#if ENABLED(NEOPIXEL_RGBW_LED)
#define NEOPIXEL_PIN 4 // D4 (EXP2-5 on Printrboard)
#define NEOPIXEL_PIXELS 3
//#define NEOPIXEL_LED
#if ENABLED(NEOPIXEL_LED)
#define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h)
#define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
#define NEOPIXEL_PIXELS 30 // Number of LEDs on strip
#define NEOPIXEL_IS_SEQUENTIAL // Sequent display for temperature change - LED by LED. Comment out for change all LED at time
#define NEOPIXEL_BRIGHTNESS 127 // Initial brightness 0-255
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
#endif

@ -1583,16 +1583,22 @@
* Adds the M150 command to set the LED (or LED strip) color.
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
* luminance values can be set from 0 to 255.
* For Neopixel LED overall brightness parameters is also available
*
* *** CAUTION ***
* LED Strips require a MOFSET Chip between PWM lines and LEDs,
* as the Arduino cannot handle the current the LEDs will require.
* Failure to follow this precaution can destroy your Arduino!
* The Neopixel LED is 5V powered, but linear 5V regulator on Arduino
* cannot handle such current, separate 5V power supply must be used
* *** CAUTION ***
*
* LED type. This options are mutualy exclusive. Uncomment only one.
*
*/
//#define RGB_LED
//#define RGBW_LED
#if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
#define RGB_LED_R_PIN 34
#define RGB_LED_G_PIN 43
@ -1601,10 +1607,13 @@
#endif
// Support for Adafruit Neopixel LED driver
//#define NEOPIXEL_RGBW_LED
#if ENABLED(NEOPIXEL_RGBW_LED)
#define NEOPIXEL_PIN 4 // D4 (EXP2-5 on Printrboard)
#define NEOPIXEL_PIXELS 3
//#define NEOPIXEL_LED
#if ENABLED(NEOPIXEL_LED)
#define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h)
#define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
#define NEOPIXEL_PIXELS 30 // Number of LEDs on strip
#define NEOPIXEL_IS_SEQUENTIAL // Sequent display for temperature change - LED by LED. Comment out for change all LED at time
#define NEOPIXEL_BRIGHTNESS 127 // Initial brightness 0-255
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
#endif

@ -1593,16 +1593,22 @@
* Adds the M150 command to set the LED (or LED strip) color.
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
* luminance values can be set from 0 to 255.
* For Neopixel LED overall brightness parameters is also available
*
* *** CAUTION ***
* LED Strips require a MOFSET Chip between PWM lines and LEDs,
* as the Arduino cannot handle the current the LEDs will require.
* Failure to follow this precaution can destroy your Arduino!
* The Neopixel LED is 5V powered, but linear 5V regulator on Arduino
* cannot handle such current, separate 5V power supply must be used
* *** CAUTION ***
*
* LED type. This options are mutualy exclusive. Uncomment only one.
*
*/
//#define RGB_LED
//#define RGBW_LED
#if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
#define RGB_LED_R_PIN 34
#define RGB_LED_G_PIN 43
@ -1611,10 +1617,13 @@
#endif
// Support for Adafruit Neopixel LED driver
//#define NEOPIXEL_RGBW_LED
#if ENABLED(NEOPIXEL_RGBW_LED)
#define NEOPIXEL_PIN 4 // D4 (EXP2-5 on Printrboard)
#define NEOPIXEL_PIXELS 3
//#define NEOPIXEL_LED
#if ENABLED(NEOPIXEL_LED)
#define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h)
#define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
#define NEOPIXEL_PIXELS 30 // Number of LEDs on strip
#define NEOPIXEL_IS_SEQUENTIAL // Sequent display for temperature change - LED by LED. Comment out for change all LED at time
#define NEOPIXEL_BRIGHTNESS 127 // Initial brightness 0-255
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
#endif

Loading…
Cancel
Save