Merge plus fixup zprobe_zoffset

- Make `zprobe_zoffset` conditional
- Fix ConfigurationStore for `zprobe_zoffset`

Marlin/ConfigurationStore.cpp

@@ -25,6 +25,7 @@
  *  mesh_num_x
  *  mesh_num_y
  *  z_values[][]
+ *  zprobe_zoffset
  *
  * DELTA:
  *  endstop_adj (x3)
@@ -39,7 +40,6 @@
  *  absPreheatHotendTemp
  *  absPreheatHPBTemp
  *  absPreheatFanSpeed
- *  zprobe_zoffset
  *
  * PIDTEMP:
  *  Kp[0], Ki[0], Kd[0], Kc[0]
@@ -118,7 +118,7 @@ void _EEPROM_readData(int &pos, uint8_t* value, uint8_t size) {
 // wrong data being written to the variables.
 // ALSO:  always make sure the variables in the Store and retrieve sections are in the same order.
 
-#define EEPROM_VERSION "V17"
+#define EEPROM_VERSION "V18"
 
 #ifdef EEPROM_SETTINGS
 
@@ -143,7 +143,7 @@ void Config_StoreSettings()  {
 
   uint8_t mesh_num_x = 3;
   uint8_t mesh_num_y = 3;
-  #if defined(MESH_BED_LEVELING)
+  #ifdef MESH_BED_LEVELING
     // Compile time test that sizeof(mbl.z_values) is as expected
     typedef char c_assert[(sizeof(mbl.z_values) == MESH_NUM_X_POINTS*MESH_NUM_Y_POINTS*sizeof(dummy)) ? 1 : -1];
     mesh_num_x = MESH_NUM_X_POINTS;
@@ -163,6 +163,11 @@ void Config_StoreSettings()  {
     }
   #endif // MESH_BED_LEVELING
 
+  #ifndef ENABLE_AUTO_BED_LEVELING
+    float zprobe_zoffset = 0;
+  #endif
+  EEPROM_WRITE_VAR(i, zprobe_zoffset);
+
   #ifdef DELTA
     EEPROM_WRITE_VAR(i, endstop_adj);               // 3 floats
     EEPROM_WRITE_VAR(i, delta_radius);              // 1 float
@@ -188,7 +193,7 @@ void Config_StoreSettings()  {
   EEPROM_WRITE_VAR(i, absPreheatHotendTemp);
   EEPROM_WRITE_VAR(i, absPreheatHPBTemp);
   EEPROM_WRITE_VAR(i, absPreheatFanSpeed);
-  EEPROM_WRITE_VAR(i, zprobe_zoffset);
+
 
   for (int e = 0; e < 4; e++) {
 
@@ -328,6 +333,11 @@ void Config_RetrieveSettings() {
       }
     #endif  // MESH_BED_LEVELING
 
+    #ifndef ENABLE_AUTO_BED_LEVELING
+      float zprobe_zoffset = 0;
+    #endif
+    EEPROM_READ_VAR(i, zprobe_zoffset);
+
     #ifdef DELTA
       EEPROM_READ_VAR(i, endstop_adj);                // 3 floats
       EEPROM_READ_VAR(i, delta_radius);               // 1 float
@@ -353,7 +363,6 @@ void Config_RetrieveSettings() {
     EEPROM_READ_VAR(i, absPreheatHotendTemp);
     EEPROM_READ_VAR(i, absPreheatHPBTemp);
     EEPROM_READ_VAR(i, absPreheatFanSpeed);
-    EEPROM_READ_VAR(i, zprobe_zoffset);
 
     #ifdef PIDTEMP
       for (int e = 0; e < 4; e++) { // 4 = max extruders currently supported by Marlin
@@ -738,8 +747,9 @@ void Config_PrintSettings(bool forReplay) {
     }
   }
 
-  #ifdef CUSTOM_M_CODES
+  #ifdef ENABLE_AUTO_BED_LEVELING
     SERIAL_ECHO_START;
+    #ifdef CUSTOM_M_CODES
       if (!forReplay) {
         SERIAL_ECHOLNPGM("Z-Probe Offset (mm):");
         SERIAL_ECHO_START;
@@ -747,6 +757,11 @@ void Config_PrintSettings(bool forReplay) {
       SERIAL_ECHO("   M");
       SERIAL_ECHO(CUSTOM_M_CODE_SET_Z_PROBE_OFFSET);
       SERIAL_ECHOPAIR(" Z", -zprobe_zoffset);
+    #else
+      if (!forReplay) {
+        SERIAL_ECHOPAIR("Z-Probe Offset (mm):", -zprobe_zoffset);
+      }
+    #endif
     SERIAL_EOL;
   #endif
 }

Marlin/Marlin.h

@@ -251,7 +251,9 @@ extern float z_endstop_adj;
 extern float min_pos[3];
 extern float max_pos[3];
 extern bool axis_known_position[3];
-extern float zprobe_zoffset;
+#ifdef ENABLE_AUTO_BED_LEVELING
+  extern float zprobe_zoffset;
+#endif
 extern int fanSpeed;
 #ifdef BARICUDA
   extern int ValvePressure;

Marlin/Marlin_main.cpp

@@ -203,7 +203,8 @@
 
 float homing_feedrate[] = HOMING_FEEDRATE;
 #ifdef ENABLE_AUTO_BED_LEVELING
-int xy_travel_speed = XY_TRAVEL_SPEED;
+  int xy_travel_speed = XY_TRAVEL_SPEED;
+  float zprobe_zoffset = -Z_PROBE_OFFSET_FROM_EXTRUDER;
 #endif
 int homing_bump_divisor[] = HOMING_BUMP_DIVISOR;
 bool axis_relative_modes[] = AXIS_RELATIVE_MODES;
@@ -255,7 +256,6 @@ float home_offset[3] = { 0, 0, 0 };
 float min_pos[3] = { X_MIN_POS, Y_MIN_POS, Z_MIN_POS };
 float max_pos[3] = { X_MAX_POS, Y_MAX_POS, Z_MAX_POS };
 bool axis_known_position[3] = { false, false, false };
-float zprobe_zoffset = -Z_PROBE_OFFSET_FROM_EXTRUDER;
 
 // Extruder offset
 #if EXTRUDERS > 1
@@ -1162,6 +1162,7 @@ static void run_z_probe() {
     zPosition += home_retract_mm(Z_AXIS);
     plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], zPosition, current_position[E_AXIS], feedrate/60, active_extruder);
     st_synchronize();
+    endstops_hit_on_purpose();
 
     // move back down slowly to find bed
     
@@ -1179,6 +1180,7 @@ static void run_z_probe() {
     zPosition -= home_retract_mm(Z_AXIS) * 2;
     plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], zPosition, current_position[E_AXIS], feedrate/60, active_extruder);
     st_synchronize();
+    endstops_hit_on_purpose();
 
     current_position[Z_AXIS] = st_get_position_mm(Z_AXIS);
     // make sure the planner knows where we are as it may be a bit different than we last said to move to
@@ -1383,11 +1385,11 @@ static float probe_pt(float x, float y, float z_before, ProbeAction retract_acti
   if (verbose_level > 2) {
     SERIAL_PROTOCOLPGM(MSG_BED);
     SERIAL_PROTOCOLPGM(" X: ");
-    SERIAL_PROTOCOL(x + 0.0001);
+    SERIAL_PROTOCOL_F(x, 3);
     SERIAL_PROTOCOLPGM(" Y: ");
-    SERIAL_PROTOCOL(y + 0.0001);
+    SERIAL_PROTOCOL_F(y, 3);
     SERIAL_PROTOCOLPGM(" Z: ");
-    SERIAL_PROTOCOL(measured_z + 0.0001);
+    SERIAL_PROTOCOL_F(measured_z, 3);
     SERIAL_EOL;
   }
   return measured_z;
@@ -2108,6 +2110,10 @@ inline void gcode_G28() {
    *
    *  S  Set the XY travel speed between probe points (in mm/min)
    *
+   *  D  Dry-Run mode. Just evaluate the bed Topology - Don't apply
+   *     or clean the rotation Matrix. Useful to check the topology
+   *     after a first run of G29.
+   *
    *  V  Set the verbose level (0-4). Example: "G29 V3"
    *
    *  T  Generate a Bed Topology Report. Example: "G29 P5 T" for a detailed report.
@@ -2149,6 +2155,7 @@ inline void gcode_G28() {
       }
     }
 
+    bool dryrun = code_seen('D') || code_seen('d');
     bool enhanced_g29 = code_seen('E') || code_seen('e');
 
     #ifdef AUTO_BED_LEVELING_GRID
@@ -2158,7 +2165,10 @@ inline void gcode_G28() {
       #endif
 
       if (verbose_level > 0)
+      {
         SERIAL_PROTOCOLPGM("G29 Auto Bed Leveling\n");
+        if (dryrun) SERIAL_ECHOLN("Running in DRY-RUN mode");
+      }
 
       int auto_bed_leveling_grid_points = AUTO_BED_LEVELING_GRID_POINTS;
       #ifndef DELTA
@@ -2215,10 +2225,13 @@ inline void gcode_G28() {
 
     st_synchronize();
 
+    if (!dryrun)
+    {
       #ifdef DELTA
         reset_bed_level();
       #else //!DELTA
-      // make sure the bed_level_rotation_matrix is identity or the planner will get it wrong
+
+        // make sure the bed_level_rotation_matrix is identity or the planner will get it incorectly
         //vector_3 corrected_position = plan_get_position_mm();
         //corrected_position.debug("position before G29");
         plan_bed_level_matrix.set_to_identity();
@@ -2228,7 +2241,9 @@ inline void gcode_G28() {
         current_position[Y_AXIS] = uncorrected_position.y;
         current_position[Z_AXIS] = uncorrected_position.z;
         plan_set_position(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS]);
-    #endif //!DELTA
+
+      #endif
+    }
     
     setup_for_endstop_move();
 
@@ -2330,9 +2345,12 @@ inline void gcode_G28() {
       clean_up_after_endstop_move();
 
       #ifdef DELTA
-        extrapolate_unprobed_bed_level();
+
+        if (!dryrun) extrapolate_unprobed_bed_level();
         print_bed_level();
+
       #else // !DELTA
+
         // solve lsq problem
         double *plane_equation_coefficients = qr_solve(abl2, 3, eqnAMatrix, eqnBVector);
 
@@ -2380,10 +2398,10 @@ inline void gcode_G28() {
         } //do_topography_map
 
 
-        set_bed_level_equation_lsq(plane_equation_coefficients);
+        if (!dryrun) set_bed_level_equation_lsq(plane_equation_coefficients);
         free(plane_equation_coefficients);
 
-      #endif // !DELTA
+      #endif //!DELTA
 
     #else // !AUTO_BED_LEVELING_GRID
 
@@ -2402,7 +2420,7 @@ inline void gcode_G28() {
         z_at_pt_3 = probe_pt(ABL_PROBE_PT_3_X, ABL_PROBE_PT_3_Y, current_position[Z_AXIS] + Z_RAISE_BETWEEN_PROBINGS, ProbeEngageAndRetract, verbose_level);
       }
       clean_up_after_endstop_move();
-      set_bed_level_equation_3pts(z_at_pt_1, z_at_pt_2, z_at_pt_3);
+      if (!dryrun) set_bed_level_equation_3pts(z_at_pt_1, z_at_pt_2, z_at_pt_3);
 
     #endif // !AUTO_BED_LEVELING_GRID
 
@@ -2413,6 +2431,8 @@ inline void gcode_G28() {
       // Correct the Z height difference from z-probe position and hotend tip position.
       // The Z height on homing is measured by Z-Probe, but the probe is quite far from the hotend.
       // When the bed is uneven, this height must be corrected.
+      if (!dryrun)
+      {
         real_z = float(st_get_position(Z_AXIS)) / axis_steps_per_unit[Z_AXIS];  //get the real Z (since the auto bed leveling is already correcting the plane)
         x_tmp = current_position[X_AXIS] + X_PROBE_OFFSET_FROM_EXTRUDER;
         y_tmp = current_position[Y_AXIS] + Y_PROBE_OFFSET_FROM_EXTRUDER;
@@ -2421,7 +2441,8 @@ inline void gcode_G28() {
         apply_rotation_xyz(plan_bed_level_matrix, x_tmp, y_tmp, z_tmp);         //Apply the correction sending the probe offset
         current_position[Z_AXIS] = z_tmp - real_z + current_position[Z_AXIS];   //The difference is added to current position and sent to planner.
         plan_set_position(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS]);
-    #endif
+      }
+    #endif // !DELTA
 
     #ifdef Z_PROBE_SLED
       dock_sled(true, -SLED_DOCKING_OFFSET); // dock the probe, correcting for over-travel

Marlin/temperature.cpp

@@ -576,6 +576,12 @@ void manage_heater() {
 
   updateTemperaturesFromRawValues();
 
+  #ifdef HEATER_0_USES_MAX6675
+    float ct = current_temperature[0];
+    if (ct > min(HEATER_0_MAXTEMP, 1023)) max_temp_error(0);
+    if (ct < max(HEATER_0_MINTEMP, 0.01)) min_temp_error(0);
+  #endif //HEATER_0_USES_MAX6675
+
   unsigned long ms = millis();
 
   // Loop through all extruders
@@ -607,7 +613,7 @@ void manage_heater() {
     #ifdef TEMP_SENSOR_1_AS_REDUNDANT
       if (fabs(current_temperature[0] - redundant_temperature) > MAX_REDUNDANT_TEMP_SENSOR_DIFF) {
         disable_heater();
-        _temp_error(-1, MSG_EXTRUDER_SWITCHED_OFF, MSG_ERR_REDUNDANT_TEMP);
+        _temp_error(0, PSTR(MSG_EXTRUDER_SWITCHED_OFF), PSTR(MSG_ERR_REDUNDANT_TEMP));
       }
     #endif //TEMP_SENSOR_1_AS_REDUNDANT
 
@@ -1162,20 +1168,40 @@ enum TempState {
   StartupDelay // Startup, delay initial temp reading a tiny bit so the hardware can settle
 };
 
-//
+#ifdef TEMP_SENSOR_1_AS_REDUNDANT
-// Timer 0 is shared with millies
-//
-ISR(TIMER0_COMPB_vect) {
-  #ifdef TEMP_SENSOR_1_AS_REDUNDANT
   #define TEMP_SENSOR_COUNT 2
-  #else 
+#else
   #define TEMP_SENSOR_COUNT EXTRUDERS
+#endif
+
+static unsigned long raw_temp_value[TEMP_SENSOR_COUNT] = { 0 };
+static unsigned long raw_temp_bed_value = 0;
+
+static void set_current_temp_raw() {
+  #ifndef HEATER_0_USES_MAX6675
+    current_temperature_raw[0] = raw_temp_value[0];
   #endif
+  #if EXTRUDERS > 1
+    current_temperature_raw[1] = raw_temp_value[1];
+    #if EXTRUDERS > 2
+      current_temperature_raw[2] = raw_temp_value[2];
+      #if EXTRUDERS > 3
+        current_temperature_raw[3] = raw_temp_value[3];
+      #endif
+    #endif
+  #endif
+  #ifdef TEMP_SENSOR_1_AS_REDUNDANT
+    redundant_temperature_raw = raw_temp_value[1];
+  #endif
+  current_temperature_bed_raw = raw_temp_bed_value;
+}
 
+//
+// Timer 0 is shared with millies
+//
+ISR(TIMER0_COMPB_vect) {
   //these variables are only accesible from the ISR, but static, so they don't lose their value
   static unsigned char temp_count = 0;
-  static unsigned long raw_temp_value[TEMP_SENSOR_COUNT] = { 0 };
-  static unsigned long raw_temp_bed_value = 0;
   static TempState temp_state = StartupDelay;
   static unsigned char pwm_count = BIT(SOFT_PWM_SCALE);
 
@@ -1478,22 +1504,7 @@ ISR(TIMER0_COMPB_vect) {
 
   if (temp_count >= OVERSAMPLENR) { // 10 * 16 * 1/(16000000/64/256)  = 164ms.
     if (!temp_meas_ready) { //Only update the raw values if they have been read. Else we could be updating them during reading.
-      #ifndef HEATER_0_USES_MAX6675
+      set_current_temp_raw();
-        current_temperature_raw[0] = raw_temp_value[0];
-      #endif
-      #if EXTRUDERS > 1
-        current_temperature_raw[1] = raw_temp_value[1];
-        #if EXTRUDERS > 2
-          current_temperature_raw[2] = raw_temp_value[2];
-          #if EXTRUDERS > 3
-            current_temperature_raw[3] = raw_temp_value[3];
-          #endif
-        #endif
-      #endif
-      #ifdef TEMP_SENSOR_1_AS_REDUNDANT
-        redundant_temperature_raw = raw_temp_value[1];
-      #endif
-      current_temperature_bed_raw = raw_temp_bed_value;
     } //!temp_meas_ready
 
     // Filament Sensor - can be read any time since IIR filtering is used
@@ -1506,11 +1517,7 @@ ISR(TIMER0_COMPB_vect) {
     for (int i = 0; i < TEMP_SENSOR_COUNT; i++) raw_temp_value[i] = 0;
     raw_temp_bed_value = 0;
 
-    #ifdef HEATER_0_USES_MAX6675
+    #ifndef HEATER_0_USES_MAX6675
-      float ct = current_temperature[0];
-      if (ct > min(HEATER_0_MAXTEMP, 1023)) max_temp_error(0);
-      if (ct < max(HEATER_0_MINTEMP, 0.01)) min_temp_error(0);
-    #else
       #if HEATER_0_RAW_LO_TEMP > HEATER_0_RAW_HI_TEMP
         #define GE0 <=
       #else

Marlin/ultralcd.cpp

@@ -204,7 +204,7 @@ static void menu_action_setting_edit_callback_long5(const char* pstr, unsigned l
   #define MENU_MULTIPLIER_ITEM_EDIT_CALLBACK(type, label, args...) MENU_ITEM(setting_edit_callback_ ## type, label, PSTR(label), ## args)
 #endif //!ENCODER_RATE_MULTIPLIER
 #define END_MENU() \
-    if (encoderLine >= _menuItemNr) encoderPosition = _menuItemNr * ENCODER_STEPS_PER_MENU_ITEM - 1; encoderLine = encoderPosition / ENCODER_STEPS_PER_MENU_ITEM;\
+    if (encoderLine >= _menuItemNr) { encoderPosition = _menuItemNr * ENCODER_STEPS_PER_MENU_ITEM - 1; encoderLine = encoderPosition / ENCODER_STEPS_PER_MENU_ITEM; }\
     if (encoderLine >= currentMenuViewOffset + LCD_HEIGHT) { currentMenuViewOffset = encoderLine - LCD_HEIGHT + 1; lcdDrawUpdate = 1; _lineNr = currentMenuViewOffset - 1; _drawLineNr = -1; } \
     } } while(0)