ba8500a236
pins.h: Define Z_MAX_PIN for Gen7 board
...
The Z_MAX_PIN value was defined as no-value, but this causes
the compile to fail. Fix this by setting the Z_MAX_PIN to the
correct value (which happens to be 0 for pin PB0/DIO0/0).
12 years ago
09469add55
Add board reset reporting (from Repetier-Firmware)
12 years ago
f3101e96d9
Add suitable .gitignore to avoid build noise
12 years ago
245dca4bee
Makefile: generic pde=>cpp rule
...
This adds flexibility to the makefile by allowing different pde
targets to be specified for different needs.
12 years ago
97d42ca2b2
SDSUPPORT default disabled
12 years ago
2faa0852b9
Merge pull request #79 from changwoo/Marlin_v1
...
Fix build on Sanguino based boards with ATmega1284P
12 years ago
7b14953c99
Fix build on Sanguino based boards with ATmega1284P
12 years ago
286d5003fa
Fixed compiler warning for Sanguino compile
12 years ago
66d50562b6
Merge pull request #76 from iXce/Marlin_v1
...
Fix Makefile
12 years ago
27f595a444
Changed version => RC2
12 years ago
018c567abf
Moved SLOWDOWN function. (jetty840)
...
Included AD595 calibration options. (daid)
12 years ago
4fbda5c3f5
Merge remote-tracking branch 'daid/Marlin_v1' into Test
12 years ago
ce714fe306
Fixes in pins.h
12 years ago
35e57bf149
Added gen6 deluxe.
12 years ago
84ea2d61e8
Moved gen7 boards to motherboard type 10, 11 and 12.
...
Split ramps1.3 in Sprinter like config and multiextruder config.
12 years ago
adc108d79e
Correctly build the produced applet/Marlin.cpp source
12 years ago
5aa9c41ab1
Changed comment mode for detection.
...
Added M221 extuder multiply factor.
12 years ago
00690f7ffd
Fix cast warning in Gen7
12 years ago
01d28c18ab
Fixed casting warning in sanguino
12 years ago
2fd8c248fe
Added Fan control to the pre-heat settings.
...
I find that the PID routine works better when the cooling fan is switched on
at the beginning of a warm up routine. Otherwise when you enable the fan
just before a print, you have a delay as the PIDre-adjusts.
This should also be safer as most cooling fans are directed at the hot -ends
thermal barrier!
12 years ago
d9f2f509d5
Added new menu items under the prepare submenu.
...
Instead of a single pre-heat, now there is pre-heat ABS and PLA options
Added defines to the configuration file to adjust preheat temperatures for both
12 years ago
ae3e7586c6
Added HOME_POS. This adds the posibility to make the center 0
...
Updated the Xsteps ... settings via the LCD menu
12 years ago
df1437bd86
Changed display format for some numbers.
12 years ago
8816ef1c64
Small fixes after merge
12 years ago
d298dd121f
merged SBUBA82 and Justblair
12 years ago
2cc9a89830
Merge remote-tracking branch 'SCUBA82/Marlin_v1' into Marlin_v1
12 years ago
a0a1f81913
various changes
12 years ago
8a8ea50f33
fixed manual axis movement lcd option
12 years ago
b976692d0f
Removed VS project files for tidyness stakes
12 years ago
fe940a142d
Added a structure that will allow easy translations/modifications to the LCD menu.
...
Signed-off-by: Blair Thompson <mail@justblair.co.uk>
12 years ago
b3fb09a20c
change preheat to ABS values of nozzle 227 and be 105 C
...
next try for manual axis movement
12 years ago
6a3f8cf23f
Infos about fuses to use; correct fuses in boards.txt
12 years ago
a05a261b72
Added a workaround. Ramps SD card does not have sdcarddetect. My temporary solution is to add a momentary swtich
...
that pulls down the SDCARDDETECT pin and mimicking the pull and reinsert ofa a SD card
12 years ago
1b6765ed12
Updated the pin config for RAMPS 1.3 to include ultimaker new style LCD/Rotary Encoder interface
12 years ago
1ff99ae25f
ATMega1284P support for Arduino IDE
...
replace $ARDUINO_HOME/hardware/tools/avr/etc/arduino.conf with this file
12 years ago
234fe8ea67
added infos for this fork
12 years ago
e661578c84
support for GEN7 1.1,1.2 and 1.3
12 years ago
73344e69c1
Added temperature offset/gain settings for AD595.
12 years ago
d309565b56
Merge remote-tracking branch 'upstream/Marlin_v1' into Marlin_v1
...
Conflicts:
Marlin/Configuration.h
12 years ago
3f20f37c78
Merge remote branch 'upstream/Marlin_v1' into Marlin_v1
12 years ago
0e3631ff4b
smaller changes
12 years ago
fa2e1be0ca
changed default EXTRUDE_MINTEMP to 170.
12 years ago
7699f250e3
Fixed small merge bug
12 years ago
11518a987f
merged with triffid fork
12 years ago
b447815de5
removed unused HEATING_EARLY_FINISH_DEG_OFFSET
...
Simplified stepper inactive time
12 years ago
bde30b2b48
Corrected e-length calculation in planner
12 years ago
13e185d330
removed unused HEATING_EARLY_FINISH_DEG_OFFSET
...
Simplified stepper inactive time
12 years ago
b58eae7657
Corrected e-length calculation in planner
12 years ago
3e7fcb813e
Merge pull request #61 from daid/Marlin_v1
...
Updated SERIAL define to MYSERIAL, because Arduino 1.0 defines SERIAL as 0.
12 years ago
2a77c84c8f
Updated SERIAL define to MYSERIAL, because Arduino 1.0 defines SERIAL as 0.
12 years ago
Phil Hord