1749a7fae3
Suppress warning
8 years ago
d07d85ac9f
Ensure probe points at the delta edge are kept
8 years ago
27b80b1dd1
Merge pull request #4667 from thinkyhead/rc_M211_sw_endstop_switch
...
M211: Enable/Disable Software Endstops
8 years ago
2f223b8c79
Use ABC and XYZ for "3"
8 years ago
4cd1ad8f28
Adjustments to M209, G28, M605
8 years ago
280534c06f
Add M211: Enable/Disable Software Endstops
8 years ago
01d4703429
PREVENT_DANGEROUS_EXTRUDE => PREVENT_COLD_EXTRUSION
...
Also improve the documentation of this and related options, and set
EXTRUDE_MINTEMP to 170 everywhere.
8 years ago
28d1e5a946
Fix_Zig_Zag
8 years ago
4d4c00d69c
Merge pull request #4651 from thinkyhead/rc_homing_vs_leveling_z
...
Improvements to homing / leveling
8 years ago
12d72363cb
Do Delta radius check without sqrt
8 years ago
044f800be9
Use SERIAL_PROTOCOLLNPGM in G28
8 years ago
d309a9647d
Include probe offset for moving "close to the bed"
8 years ago
35a08eeaeb
Use Z_HOME_DIR over axis_home_dir where we can
8 years ago
55355a4fb8
Make probed points more symmetrical
8 years ago
1f776f6034
Tweak some code comments
8 years ago
748228cf40
Use named indices for delta_grid_spacing
8 years ago
ead333e7da
line_to_axis_pos => do_homing_move
8 years ago
7a4ccd7967
Add do_probe_move with Z fixes
8 years ago
a1bad589c9
Augment debug/homing logging
8 years ago
41b5c48129
Update software endstops if EEPROM is loaded
8 years ago
628dcbc764
extruder_multiplier => flow_percentage
8 years ago
d63b8e2b2b
Additional details for I2C_SLAVE_ADDRESS
8 years ago
bd928a69ec
Add request, capture, flush to TWIBus
8 years ago
97e0aed304
Further refinements of TWIBus
8 years ago
67f119d18b
Add an i2c request handler
8 years ago
d6a7ca6553
Merge pull request #4584 from thinkyhead/rc_delta_cal_more
...
Use configured feedrates, center in DELTA_CALIBRATION_MENU
8 years ago
52560e257f
Merge pull request #4595 from thinkyhead/rc_i2c_slave
...
Add support for i2c slave address
8 years ago
cd496dd9bd
do_blocking_move_to can't be 'inline', takes const ref args
8 years ago
dd75fca4d9
Make M155 / M156 a bit more flexible
8 years ago
a99ecf71d8
Add support for i2c slave address
8 years ago
b63d70b186
Fix serial output for MBL, M303
8 years ago
45f67164b6
Simplify the delay in kill()
8 years ago
367dad5902
Sanity check Z_DUAL_ENDSTOPS with DELTA
9 years ago
7b2abe6fc8
Use steps_to_mm in extruder runout prevent
9 years ago
d320065320
Within Marlin, maintain most feed rates in mm/s
9 years ago
a00783c41f
Format probe stowed test code
9 years ago
f37e8a31d7
Make Allen Key Probe stow
...
by switching off the tests for the probe before the stow move.
9 years ago
938e6d15c4
Patch up some flaws, here and there
9 years ago
7e2bd9a233
Z_RAISE_PROBE_* => Z_PROBE_*_HEIGHT
9 years ago
445458c221
Don't include `zprobe_zoffset` in `do_probe_raise`
9 years ago
b73203a0b7
Move some includes around to uncover missing deps
9 years ago
0f030aface
Merge pull request #4503 from AnHardt/fix-retract
...
Correct typo in retract()
9 years ago
330f82971b
Buzzer requires BEEPER_PIN
9 years ago
39c4603598
Correct typo in retract.
9 years ago
6eed37aafb
Merge pull request #4486 from thinkyhead/rc_pid_add_extrusion_rate_off
...
PID_EXTRUSION_SCALING, disabled by default
9 years ago
4bf3526d00
Merge pull request #4463 from thinkyhead/rc_azteeg_x3_eeb
...
Wrangle RAMPS variants and derivatives
9 years ago
63fd1f49a6
PID_EXTRUSION_SCALING, disabled by default
9 years ago
f388beafa1
Merge pull request #4476 from otvald/RCBugFix
...
FIX for endstop adjustemt on delta is offset
9 years ago
fe059f1221
During homing, line_to_axis_pos will make a path which moves across the
...
endstop trigger point. The move is stopped at endstop, so current_position
should also be adjusted to reflect this!
Caused error in subsequent call in endstop adjustment, since the movement
would assume a wrong starting position.
9 years ago
bd73e6d3c8
Fix for PR #4452 (Additional heater-state output changes)
...
・Add missing ';'
9 years ago
esenapaj