1fa61c297e
Turning off Control Panel by Default and Updating the link to the LiquidCrystal_I2C library to avoid confusion.
12 years ago
b27a59f41e
Added support for Elefu RA Board and Elefu Control Panel
12 years ago
1a397825f9
fix DEFAULT_AXIS_STEPS_PER_UNIT minor Z rounding error
12 years ago
d71f1e9bf6
Add (as an option) slower SD transfer mode
12 years ago
13596e8722
Added RepRapDiscount FULL GRAPHIC Smart Controller
12 years ago
c80a78bb70
Lower the default max E feedrate a bit. With the stepper fix this is much to high.
12 years ago
7a5c474d91
Update Configuration.h
12 years ago
9fb8bd5685
Merge pull request #433 from whosawhatsis/bang-mode
...
Separate PID_MAX from BANG_MAX
12 years ago
fd5b7e0cec
Separate PID_MAX from BANG_MAX
...
This allows PID_FUNCTIONAL_RANGE to use a maximum duty cycle higher
than PID_MAX. This is useful for powerful heaters to heat quickly in
bang-bang mode, but use a lower duty cycle that is easier to stabilize
in PID mode.
12 years ago
72419f69a9
Added rumba
12 years ago
b2c1c64fb1
Add Motherboard variant 64 - STB V1.1
...
Definition for the graphic LCD are already in it, they will not harm the
configuration as they are only defined constants
12 years ago
70871715e4
Added support for extruder offset handling
...
The extruder offset can be specified in the configuration
file or adjusted on the fly using the "M218 T# X# Y#" command.
The EEPROM support is not yet merged in.
The "T#" command can take option "F#" that specifies the feedrate
at which the printing head should be re-positioned. If not
specified the re-positioning move is not preformed immediately,
but the coordinates are adjusted for the printer to properly
position the head when the next movement happens.
12 years ago
9ecb267b63
Merge remote-tracking branch 'upstream/Marlin_v1' into Marlin_v1
12 years ago
3cf59f6f9a
add RepRapPro Huxley thermistor tables
12 years ago
bbe7d3d0fe
Fixed #312
12 years ago
8b88e3b386
Fixed #345 , Fixed #267 .
12 years ago
f3c1fc70a9
Power signal control definitions for ATX and others
12 years ago
55ba90ac19
Add PID functional range setting. With high powered heaters the current functional range of 10 degrees causes high overshoots as the PID needs to kick in before the temperature hits 10 degrees below target.
12 years ago
5ff5cee8ce
Fix the sensitive pin definitions, there where analogue numbers in the digital pin list. Also made M42 without a P function on the LED_PIN (which was otherwise a useless pin definition)
12 years ago
1f45cb0a51
Fix typo in MANUAL_HOME_POSITION (plural S missing) and improve comments.
12 years ago
42e21bb06e
Add support for Printrboard (from https://github.com/lincomatic/Marlin ) and Brainwave (from https://github.com/metrix/Sprinter ).
12 years ago
f934d0ef5b
Merge remote-tracking branch 'tonokip/Marlin_v1' into Marlin_v1
...
Conflicts:
Marlin/Configuration.h
12 years ago
2f771b3979
Added automatic build numbering.
12 years ago
a27fef8750
Store the pre-heat constants outside of the ULTIPANEL define, so we can use them when storing EEPROM in a build without the ULTIPANEL.
12 years ago
ffc69537aa
Update on some comments, make the MOTHERBOARD list complete again.
12 years ago
46b9988e26
Search and replace failure.
12 years ago
36b452c7ac
Remove abbrs.
12 years ago
3cbaad9288
RepRapDiscount Smart Controller pin definitions.
12 years ago
65c9a0728f
Set default serial port back to 0.
12 years ago
ab9d183024
Make serial port configurable.
...
This change makes the choice of serial port configurable so that
wireless capability can be easily added by connecting Bluetooth modules
(such as BlueSmirf or JY-MCU) to the expansion port pins.
12 years ago
326423719f
Add support for Megatronics
12 years ago
36a746d7d5
Merge pull request #244 from markfinn/pidbed
...
PID for heated bed
12 years ago
04631d2250
cleanup for pull
12 years ago
c6caa45ae2
Limit Switch locations based on MIN/MAX limits and homing direction
...
fixes #246
Added statements to set the limit switch positions to the maximum travel if homing in the positive direction as well as bed center at (0,0) if defined.
Relocated code based on feedback.
12 years ago
dc566d654f
fixes #246
...
Added statements to set the limit switch positions to the maximum travel if homing in the positive direction as well as bed center at (0,0) if defined.
12 years ago
9698f4ea64
bed pid
...
Conflicts:
Marlin/Configuration.h
12 years ago
e358a2d7af
Added fix for SF Arc Point fillet procedure
12 years ago
1c1fddc7ac
Added support for the Rambo reprap electronics board. Added Mcodes to set
...
motor current and microstepping pins.
12 years ago
5406c533db
Disable FAST_PWM by default. On some systems it does not work ok.
12 years ago
6b45e9f167
Add Duty Cycling to the Heater Bed
12 years ago
538189cc19
Fixed soft limits when the origin is in the middle.
...
HOME_POS is now always where the endstop is and can be outside the limits.
The limits are now defined by MIN_POS and MAX_POS rather than HOME_POS and MAX_LENGTH.
The Z is axis now homed first if direction is away from the bed.
Saguinololu limit pins change from MIN to MAX according to the homing direction.
13 years ago
ea2c19f978
Added CoreXY support (Thanks Ilan Moyer)
13 years ago
aa65fe22ed
decoupled axes sucessfully at least on pure x or y jog
13 years ago
0c123950e9
__ header file replace
13 years ago
0e5e249ab5
added individual pullup setting option to have finer control in case there is a special z-min sensor, for example
13 years ago
6b14f95b3e
Merge pull request #170 from linagee/Marlin_v1
...
Marlin v1
13 years ago
fbd282b3ba
Update Marlin/Configuration.h
13 years ago
c4490f5f3d
Update Marlin/Configuration.h
13 years ago
7244aa7eb7
Merge branch 'Marlin_v1' of https://github.com/ErikZalm/Marlin into Marlin_v1
13 years ago
de2ca3b2e8
Grammar correction.
13 years ago
Tim Anderson