You can not select more than 25 topics Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
qmk_firmware/Projects/AVRISP-MKII/AVRISP-MKII.c

155 lines
5.3 KiB

/*
LUFA Library
Copyright (C) Dean Camera, 2012.
dean [at] fourwalledcubicle [dot] com
www.lufa-lib.org
*/
/*
Copyright 2012 Dean Camera (dean [at] fourwalledcubicle [dot] com)
Permission to use, copy, modify, distribute, and sell this
software and its documentation for any purpose is hereby granted
without fee, provided that the above copyright notice appear in
all copies and that both that the copyright notice and this
permission notice and warranty disclaimer appear in supporting
documentation, and that the name of the author not be used in
advertising or publicity pertaining to distribution of the
software without specific, written prior permission.
The author disclaim all warranties with regard to this
software, including all implied warranties of merchantability
and fitness. In no event shall the author be liable for any
special, indirect or consequential damages or any damages
whatsoever resulting from loss of use, data or profits, whether
in an action of contract, negligence or other tortious action,
arising out of or in connection with the use or performance of
this software.
*/
/** \file
*
* Main source file for the AVRISP project. This file contains the main tasks of
* the project and is responsible for the initial application hardware configuration.
*/
#include "AVRISP-MKII.h"
/** Main program entry point. This routine contains the overall program flow, including initial
* setup of all components and the main program loop.
*/
int main(void)
{
SetupHardware();
V2Protocol_Init();
LEDs_SetAllLEDs(LEDMASK_USB_NOTREADY);
GlobalInterruptEnable();
for (;;)
{
#if (BOARD == BOARD_USBTINYMKII)
/* On the USBTINY-MKII target, there is a secondary LED which indicates the current selected power
mode - either VBUS, or sourced from the VTARGET pin of the programming connectors */
LEDs_ChangeLEDs(LEDMASK_VBUSPOWER, (PIND & (1 << 0)) ? 0 : LEDMASK_VBUSPOWER);
#endif
AVRISP_Task();
USB_USBTask();
}
}
/** Configures the board hardware and chip peripherals for the demo's functionality. */
void SetupHardware(void)
{
/* Disable watchdog if enabled by bootloader/fuses */
MCUSR &= ~(1 << WDRF);
wdt_disable();
/* Disable clock division */
clock_prescale_set(clock_div_1);
/* Hardware Initialization */
LEDs_Init();
#if defined(RESET_TOGGLES_LIBUSB_COMPAT)
UpdateCurrentCompatibilityMode();
#endif
/* USB Stack Initialization */
USB_Init();
}
/** Event handler for the library USB Connection event. */
void EVENT_USB_Device_Connect(void)
{
LEDs_SetAllLEDs(LEDMASK_USB_ENUMERATING);
}
/** Event handler for the library USB Disconnection event. */
void EVENT_USB_Device_Disconnect(void)
{
LEDs_SetAllLEDs(LEDMASK_USB_NOTREADY);
}
/** Event handler for the library USB Configuration Changed event. */
void EVENT_USB_Device_ConfigurationChanged(void)
{
bool ConfigSuccess = true;
/* Setup AVRISP Data OUT endpoint */
ConfigSuccess &= Endpoint_ConfigureEndpoint(AVRISP_DATA_OUT_EPADDR, EP_TYPE_BULK, AVRISP_DATA_EPSIZE, 1);
/* Setup AVRISP Data IN endpoint if it is using a physically different endpoint */
if ((AVRISP_DATA_IN_EPADDR & ENDPOINT_EPNUM_MASK) != (AVRISP_DATA_OUT_EPADDR & ENDPOINT_EPNUM_MASK))
ConfigSuccess &= Endpoint_ConfigureEndpoint(AVRISP_DATA_IN_EPADDR, EP_TYPE_BULK, AVRISP_DATA_EPSIZE, 1);
/* Indicate endpoint configuration success or failure */
LEDs_SetAllLEDs(ConfigSuccess ? LEDMASK_USB_READY : LEDMASK_USB_ERROR);
}
/** Processes incoming V2 Protocol commands from the host, returning a response when required. */
void AVRISP_Task(void)
{
/* Device must be connected and configured for the task to run */
if (USB_DeviceState != DEVICE_STATE_Configured)
return;
V2Params_UpdateParamValues();
Endpoint_SelectEndpoint(AVRISP_DATA_OUT_EPADDR);
/* Check to see if a V2 Protocol command has been received */
if (Endpoint_IsOUTReceived())
{
LEDs_SetAllLEDs(LEDMASK_BUSY);
/* Pass off processing of the V2 Protocol command to the V2 Protocol handler */
V2Protocol_ProcessCommand();
LEDs_SetAllLEDs(LEDMASK_USB_READY);
}
}
/** This function is called by the library when in device mode, and must be overridden (see library "USB Descriptors"
* documentation) by the application code so that the address and size of a requested descriptor can be given
* to the USB library. When the device receives a Get Descriptor request on the control endpoint, this function
* is called so that the descriptor details can be passed back and the appropriate descriptor sent back to the
* USB host.
*
* \param[in] wValue Descriptor type and index to retrieve
* \param[in] wIndex Sub-index to retrieve (such as a localized string language)
* \param[out] DescriptorAddress Address of the retrieved descriptor
* \param[out] DescriptorMemorySpace Memory space that the descriptor is stored in
*
* \return Length of the retrieved descriptor in bytes, or NO_DESCRIPTOR if the descriptor was not found
*/
uint16_t CALLBACK_USB_GetDescriptor(const uint16_t wValue,
const uint8_t wIndex,
const void** const DescriptorAddress,
uint8_t* DescriptorMemorySpace)
{
return AVRISP_GetDescriptor(wValue, wIndex, DescriptorAddress, DescriptorMemorySpace);
}