Add new incomplete HIDReportViewer project.

pull/1469/head
Dean Camera 14 years ago
parent 0ec2b55a7c
commit 00acc95ff6

File diff suppressed because one or more lines are too long

@ -15,6 +15,7 @@
* - Added Audio class control request definitions * - Added Audio class control request definitions
* - Added new CALLBACK_Audio_Device_GetSetEndpointProperty() callback to the Audio Device Class driver to allow for endpoint control manipulations * - Added new CALLBACK_Audio_Device_GetSetEndpointProperty() callback to the Audio Device Class driver to allow for endpoint control manipulations
* such as data sample rates * such as data sample rates
* - Added support for the Audio class GET STATUS request in the Audio Device Class driver so that it is correctly ACKed when sent by the host
* - Added new EVENT_Audio_Device_StreamStartStop() event to the Audio Device Class driver to detect stream start/stop events * - Added new EVENT_Audio_Device_StreamStartStop() event to the Audio Device Class driver to detect stream start/stop events
* - Added board driver support for the Busware TUL board * - Added board driver support for the Busware TUL board
* - Added new Host mode Audio Class driver * - Added new Host mode Audio Class driver
@ -30,14 +31,13 @@
* *
* <b>Changed:</b> * <b>Changed:</b>
* - Core: * - Core:
* - Added support for the Audio class GET STATUS request so that it is correctly ACKed when sent by the host
* - Altered the definition of the USB_Audio_Descriptor_Format_t descriptor so that the user is now responsible for supplying * - Altered the definition of the USB_Audio_Descriptor_Format_t descriptor so that the user is now responsible for supplying
* the supported audio sampling rates, to allow for multiple audio interfaces with different numbers of supported rates and/or * the supported audio sampling rates, to allow for multiple audio interfaces with different numbers of supported rates and/or
* continuous sample rates * continuous sample rates
* - Pipe_BoundEndpointNumber() has been renamed to Pipe_GetBoundEndpointAddress(), and now returns the correct endpoint direction * - Pipe_BoundEndpointNumber() has been renamed to Pipe_GetBoundEndpointAddress(), and now returns the correct endpoint direction
* as part of the endpoint address * as part of the endpoint address
* - Library Applications: * - Library Applications:
* - Modified the Low Level and Class Driver AudioInput and AudioOutput demos to support multiple sample rates * - Modified the Low Level and Class Driver AudioInput and AudioOutput demos to support multiple audio sample rates
* *
* <b>Fixed:</b> * <b>Fixed:</b>
* - Core: * - Core:

@ -23,7 +23,6 @@
* -# Add a LUFA_YIELD macro for integration into a third-party RTOS * -# Add a LUFA_YIELD macro for integration into a third-party RTOS
* -# Abstract out Mass Storage byte send/receive to prevent low level API use in projects * -# Abstract out Mass Storage byte send/receive to prevent low level API use in projects
* -# Consider switch from endpoint numbers to full endpoint addresses to ease future architecture expansion * -# Consider switch from endpoint numbers to full endpoint addresses to ease future architecture expansion
* -# Add architecture sanity guards to arch-specific files so that entire tree can be built from an IDE
* - Documentation/Support * - Documentation/Support
* -# Add detailed overviews of how each demo works * -# Add detailed overviews of how each demo works
* -# Add board overviews * -# Add board overviews
@ -31,6 +30,7 @@
* - Demos/Projects * - Demos/Projects
* -# Device/Host USB bridge * -# Device/Host USB bridge
* -# Finish incomplete demos and projects * -# Finish incomplete demos and projects
* -# HID Report Parser Dumper Project
* -# Add class driver support for Test and Measurement class * -# Add class driver support for Test and Measurement class
* -# Add class driver support for EEM class * -# Add class driver support for EEM class
* -# Add class driver support for ECM class * -# Add class driver support for ECM class

@ -0,0 +1,286 @@
/*
LUFA Library
Copyright (C) Dean Camera, 2011.
dean [at] fourwalledcubicle [dot] com
www.lufa-lib.org
*/
/*
Copyright 2011 Dean Camera (dean [at] fourwalledcubicle [dot] com)
Permission to use, copy, modify, distribute, and sell this
software and its documentation for any purpose is hereby granted
without fee, provided that the above copyright notice appear in
all copies and that both that the copyright notice and this
permission notice and warranty disclaimer appear in supporting
documentation, and that the name of the author not be used in
advertising or publicity pertaining to distribution of the
software without specific, written prior permission.
The author disclaim all warranties with regard to this
software, including all implied warranties of merchantability
and fitness. In no event shall the author be liable for any
special, indirect or consequential damages or any damages
whatsoever resulting from loss of use, data or profits, whether
in an action of contract, negligence or other tortious action,
arising out of or in connection with the use or performance of
this software.
*/
#include "HIDReportViewer.h"
/** Processed HID report descriptor items structure, containing information on each HID report element */
static HID_ReportInfo_t HIDReportInfo;
/** LUFA HID Class driver interface configuration and state information. This structure is
* passed to all HID Class driver functions, so that multiple instances of the same class
* within a device can be differentiated from one another.
*/
USB_ClassInfo_HID_Host_t Device_HID_Interface =
{
.Config =
{
.DataINPipeNumber = 1,
.DataINPipeDoubleBank = false,
.DataOUTPipeNumber = 2,
.DataOUTPipeDoubleBank = false,
.HIDInterfaceProtocol = HID_CSCP_NonBootProtocol,
.HIDParserData = &HIDReportInfo
},
};
/** Main program entry point. This routine configures the hardware required by the application, then
* enters a loop to run the application tasks in sequence.
*/
int main(void)
{
SetupHardware();
puts_P(PSTR(ESC_FG_CYAN "HID Device Report Viewer Running.\r\n" ESC_FG_WHITE));
LEDs_SetAllLEDs(LEDMASK_USB_NOTREADY);
sei();
for (;;)
{
switch (USB_HostState)
{
case HOST_STATE_Addressed:
LEDs_SetAllLEDs(LEDMASK_USB_ENUMERATING);
uint16_t ConfigDescriptorSize;
uint8_t ConfigDescriptorData[512];
if (USB_Host_GetDeviceConfigDescriptor(1, &ConfigDescriptorSize, ConfigDescriptorData,
sizeof(ConfigDescriptorData)) != HOST_GETCONFIG_Successful)
{
puts_P(PSTR("Error Retrieving Configuration Descriptor.\r\n"));
LEDs_SetAllLEDs(LEDMASK_USB_ERROR);
USB_HostState = HOST_STATE_WaitForDeviceRemoval;
break;
}
if (HID_Host_ConfigurePipes(&Device_HID_Interface,
ConfigDescriptorSize, ConfigDescriptorData) != HID_ENUMERROR_NoError)
{
puts_P(PSTR("Attached Device Not a Valid HID Device.\r\n"));
LEDs_SetAllLEDs(LEDMASK_USB_ERROR);
USB_HostState = HOST_STATE_WaitForDeviceRemoval;
break;
}
if (USB_Host_SetDeviceConfiguration(1) != HOST_SENDCONTROL_Successful)
{
puts_P(PSTR("Error Setting Device Configuration.\r\n"));
LEDs_SetAllLEDs(LEDMASK_USB_ERROR);
USB_HostState = HOST_STATE_WaitForDeviceRemoval;
break;
}
if (HID_Host_SetReportProtocol(&Device_HID_Interface) != 0)
{
puts_P(PSTR("Error Setting Report Protocol Mode.\r\n"));
LEDs_SetAllLEDs(LEDMASK_USB_ERROR);
USB_HostState = HOST_STATE_WaitForDeviceRemoval;
break;
}
puts_P(PSTR("HID Device Enumerated.\r\n"));
LEDs_SetAllLEDs(LEDMASK_USB_READY);
USB_HostState = HOST_STATE_Configured;
break;
case HOST_STATE_Configured:
LEDs_SetAllLEDs(LEDMASK_USB_BUSY);
printf_P(PSTR("\r\n\r\nTotal Reports: %d\r\n"), HIDReportInfo.TotalDeviceReports);
for (uint8_t ReportIndex = 0; ReportIndex < HIDReportInfo.TotalDeviceReports; ReportIndex++)
{
HID_ReportSizeInfo_t* CurrReportIDInfo = &HIDReportInfo.ReportIDSizes[ReportIndex];
uint8_t ReportSizeInBits = CurrReportIDInfo->ReportSizeBits[HID_REPORT_ITEM_In];
uint8_t ReportSizeOutBits = CurrReportIDInfo->ReportSizeBits[HID_REPORT_ITEM_Out];
uint8_t ReportSizeFeatureBits = CurrReportIDInfo->ReportSizeBits[HID_REPORT_ITEM_Feature];
/* Print out the byte sizes of each report within the device */
printf_P(PSTR(" + Report ID %d - In: %d bytes, Out: %d bytes, Feature: %d bytes\r\n"),
CurrReportIDInfo->ReportID,
((ReportSizeInBits >> 3) + ((ReportSizeInBits & 0x07) != 0)),
((ReportSizeOutBits >> 3) + ((ReportSizeOutBits & 0x07) != 0)),
((ReportSizeFeatureBits >> 3) + ((ReportSizeFeatureBits & 0x07) != 0)));
}
printf_P(PSTR("\r\n\r\nReport Items: %d\r\n"), HIDReportInfo.TotalDeviceReports);
for (uint8_t ItemIndex = 0; ItemIndex < HIDReportInfo.TotalReportItems; ItemIndex++)
{
HID_ReportItem_t* RItem = &HIDReportInfo.ReportItems[ItemIndex];
printf_P(PSTR(" + Item %d:\r\n"
" - Report ID: 0x%02X\r\n"
" - Data Direction: %s\r\n"
" - Item Flags: 0x%02X\r\n"
" - Item Offset (Bits): 0x%02X\r\n"
" - Item Size (Bits): 0x%02X\r\n"
" - Usage Page: 0x%04X\r\n"
" - Usage: 0x%04X\r\n"
" - Unit Type: 0x%04X\r\n"
" - Unit Exponent: 0x%02X\r\n"
" - Logical Minimum: 0x%04X\r\n"
" - Logical Maximum: 0x%04X\r\n"
" - Physical Minimum: 0x%04X\r\n"
" - Physical Maximum: 0x%04X\r\n"
" - Collection Path:\r\n"),
ItemIndex,
RItem->ReportID,
((RItem->ItemType == HID_REPORT_ITEM_In) ? "IN" : ((RItem->ItemType == HID_REPORT_ITEM_Out) ? "OUT" : "FEATURE")),
RItem->ItemFlags,
RItem->BitOffset,
RItem->Attributes.BitSize,
RItem->Attributes.Usage.Page,
RItem->Attributes.Usage.Usage,
RItem->Attributes.Unit.Type,
RItem->Attributes.Unit.Exponent,
RItem->Attributes.Logical.Minimum,
RItem->Attributes.Logical.Maximum,
RItem->Attributes.Physical.Minimum,
RItem->Attributes.Physical.Maximum);
HID_CollectionPath_t* CollectionPath = RItem->CollectionPath;
uint8_t CollectionDepth = 6;
while (CollectionPath != NULL)
{
for (uint8_t i = 0; i < CollectionDepth; i++)
putchar(' ');
printf_P(PSTR("- Type: 0x%02X\r\n"), CollectionPath->Type);
for (uint8_t i = 0; i < CollectionDepth; i++)
putchar(' ');
printf_P(PSTR("- Usage: 0x%02X\r\n"), CollectionPath->Usage);
CollectionDepth += 3;
CollectionPath = CollectionPath->Parent;
}
}
LEDs_SetAllLEDs(LEDMASK_USB_READY);
USB_HostState = HOST_STATE_WaitForDeviceRemoval;
break;
}
HID_Host_USBTask(&Device_HID_Interface);
USB_USBTask();
}
}
/** Configures the board hardware and chip peripherals for the demo's functionality. */
void SetupHardware(void)
{
/* Disable watchdog if enabled by bootloader/fuses */
MCUSR &= ~(1 << WDRF);
wdt_disable();
/* Disable clock division */
clock_prescale_set(clock_div_1);
/* Hardware Initialization */
Serial_Init(9600, false);
LEDs_Init();
USB_Init();
/* Create a stdio stream for the serial port for stdin and stdout */
Serial_CreateStream(NULL);
}
/** Event handler for the USB_DeviceAttached event. This indicates that a device has been attached to the host, and
* starts the library USB task to begin the enumeration and USB management process.
*/
void EVENT_USB_Host_DeviceAttached(void)
{
puts_P(PSTR("Device Attached.\r\n"));
LEDs_SetAllLEDs(LEDMASK_USB_ENUMERATING);
}
/** Event handler for the USB_DeviceUnattached event. This indicates that a device has been removed from the host, and
* stops the library USB task management process.
*/
void EVENT_USB_Host_DeviceUnattached(void)
{
puts_P(PSTR("\r\nDevice Unattached.\r\n"));
LEDs_SetAllLEDs(LEDMASK_USB_NOTREADY);
}
/** Event handler for the USB_DeviceEnumerationComplete event. This indicates that a device has been successfully
* enumerated by the host and is now ready to be used by the application.
*/
void EVENT_USB_Host_DeviceEnumerationComplete(void)
{
LEDs_SetAllLEDs(LEDMASK_USB_READY);
}
/** Event handler for the USB_HostError event. This indicates that a hardware error occurred while in host mode. */
void EVENT_USB_Host_HostError(const uint8_t ErrorCode)
{
USB_Disable();
printf_P(PSTR(ESC_FG_RED "Host Mode Error\r\n"
" -- Error Code %d\r\n" ESC_FG_WHITE), ErrorCode);
LEDs_SetAllLEDs(LEDMASK_USB_ERROR);
for(;;);
}
/** Event handler for the USB_DeviceEnumerationFailed event. This indicates that a problem occurred while
* enumerating an attached USB device.
*/
void EVENT_USB_Host_DeviceEnumerationFailed(const uint8_t ErrorCode,
const uint8_t SubErrorCode)
{
printf_P(PSTR(ESC_FG_RED "Dev Enum Error\r\n"
" -- Error Code %d\r\n"
" -- Sub Error Code %d\r\n"
" -- In State %d\r\n" ESC_FG_WHITE), ErrorCode, SubErrorCode, USB_HostState);
LEDs_SetAllLEDs(LEDMASK_USB_ERROR);
}
/** Callback for the HID Report Parser. This function is called each time the HID report parser is about to store
* an IN, OUT or FEATURE item into the HIDReportInfo structure. To save on RAM, we are able to filter out items
* we aren't interested in (preventing us from being able to extract them later on, but saving on the RAM they would
* have occupied).
*
* \param[in] CurrentItem Pointer to the item the HID report parser is currently working with
*
* \return Boolean true if the item should be stored into the HID report structure, false if it should be discarded
*/
bool CALLBACK_HIDParser_FilterHIDReportItem(HID_ReportItem_t* const CurrentItem)
{
return true;
}

@ -0,0 +1,82 @@
/*
LUFA Library
Copyright (C) Dean Camera, 2011.
dean [at] fourwalledcubicle [dot] com
www.lufa-lib.org
*/
/*
Copyright 2011 Dean Camera (dean [at] fourwalledcubicle [dot] com)
Permission to use, copy, modify, distribute, and sell this
software and its documentation for any purpose is hereby granted
without fee, provided that the above copyright notice appear in
all copies and that both that the copyright notice and this
permission notice and warranty disclaimer appear in supporting
documentation, and that the name of the author not be used in
advertising or publicity pertaining to distribution of the
software without specific, written prior permission.
The author disclaim all warranties with regard to this
software, including all implied warranties of merchantability
and fitness. In no event shall the author be liable for any
special, indirect or consequential damages or any damages
whatsoever resulting from loss of use, data or profits, whether
in an action of contract, negligence or other tortious action,
arising out of or in connection with the use or performance of
this software.
*/
/** \file
*
* Header file for HIDReportViewer.c.
*/
#ifndef _HID_REPORT_VIEWER_H_
#define _HID_REPORT_VIEWER_H_
/* Includes: */
#include <avr/io.h>
#include <avr/wdt.h>
#include <avr/pgmspace.h>
#include <avr/power.h>
#include <avr/interrupt.h>
#include <stdio.h>
#include <LUFA/Version.h>
#include <LUFA/Drivers/Misc/TerminalCodes.h>
#include <LUFA/Drivers/Peripheral/Serial.h>
#include <LUFA/Drivers/Board/LEDs.h>
#include <LUFA/Drivers/USB/USB.h>
/* Macros: */
/** LED mask for the library LED driver, to indicate that the USB interface is not ready. */
#define LEDMASK_USB_NOTREADY LEDS_LED1
/** LED mask for the library LED driver, to indicate that the USB interface is enumerating. */
#define LEDMASK_USB_ENUMERATING (LEDS_LED2 | LEDS_LED3)
/** LED mask for the library LED driver, to indicate that the USB interface is ready. */
#define LEDMASK_USB_READY (LEDS_LED2 | LEDS_LED4)
/** LED mask for the library LED driver, to indicate that an error has occurred in the USB interface. */
#define LEDMASK_USB_ERROR (LEDS_LED1 | LEDS_LED3)
/** LED mask for the library LED driver, to indicate that the USB interface is busy. */
#define LEDMASK_USB_BUSY (LEDS_LED1 | LEDS_LED3 | LEDS_LED4)
/* Function Prototypes: */
void SetupHardware(void);
void EVENT_USB_Host_HostError(const uint8_t ErrorCode);
void EVENT_USB_Host_DeviceAttached(void);
void EVENT_USB_Host_DeviceUnattached(void);
void EVENT_USB_Host_DeviceEnumerationFailed(const uint8_t ErrorCode,
const uint8_t SubErrorCode);
void EVENT_USB_Host_DeviceEnumerationComplete(void);
bool CALLBACK_HIDParser_FilterHIDReportItem(HID_ReportItem_t* const CurrentItem);
#endif

@ -0,0 +1,714 @@
# Hey Emacs, this is a -*- makefile -*-
#----------------------------------------------------------------------------
# WinAVR Makefile Template written by Eric B. Weddington, Jörg Wunsch, et al.
# >> Modified for use with the LUFA project. <<
#
# Released to the Public Domain
#
# Additional material for this makefile was written by:
# Peter Fleury
# Tim Henigan
# Colin O'Flynn
# Reiner Patommel
# Markus Pfaff
# Sander Pool
# Frederik Rouleau
# Carlos Lamas
# Dean Camera
# Opendous Inc.
# Denver Gingerich
#
#----------------------------------------------------------------------------
# On command line:
#
# make all = Make software.
#
# make clean = Clean out built project files.
#
# make coff = Convert ELF to AVR COFF.
#
# make extcoff = Convert ELF to AVR Extended COFF.
#
# make program = Download the hex file to the device, using avrdude.
# Please customize the avrdude settings below first!
#
# make dfu = Download the hex file to the device, using dfu-programmer (must
# have dfu-programmer installed).
#
# make flip = Download the hex file to the device, using Atmel FLIP (must
# have Atmel FLIP installed).
#
# make dfu-ee = Download the eeprom file to the device, using dfu-programmer
# (must have dfu-programmer installed).
#
# make flip-ee = Download the eeprom file to the device, using Atmel FLIP
# (must have Atmel FLIP installed).
#
# make doxygen = Generate DoxyGen documentation for the project (must have
# DoxyGen installed)
#
# make debug = Start either simulavr or avarice as specified for debugging,
# with avr-gdb or avr-insight as the front end for debugging.
#
# make filename.s = Just compile filename.c into the assembler code only.
#
# make filename.i = Create a preprocessed source file for use in submitting
# bug reports to the GCC project.
#
# To rebuild project do "make clean" then "make all".
#----------------------------------------------------------------------------
# MCU name
MCU = at90usb1287
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Target board (see library "Board Types" documentation, NONE for projects not requiring
# LUFA board drivers). If USER is selected, put custom board drivers in a directory called
# "Board" inside the application directory.
BOARD = USBKEY
# Processor frequency.
# This will define a symbol, F_CPU, in all source code files equal to the
# processor frequency in Hz. You can then use this symbol in your source code to
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
# automatically to create a 32-bit value in your source code.
#
# This will be an integer division of F_USB below, as it is sourced by
# F_USB after it has run through any CPU prescalers. Note that this value
# does not *change* the processor frequency - it should merely be updated to
# reflect the processor speed set externally so that the code can use accurate
# software delays.
F_CPU = 8000000
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
# Output format. (can be srec, ihex, binary)
FORMAT = ihex
# Target file name (without extension).
TARGET = HIDReportViewer
# Object files directory
# To put object files in current directory, use a dot (.), do NOT make
# this an empty or blank macro!
OBJDIR = .
# Path to the LUFA library
LUFA_PATH = ../../..
# LUFA library compile-time options and predefined tokens
LUFA_OPTS = -D USB_HOST_ONLY
LUFA_OPTS += -D USE_STATIC_OPTIONS="(USB_OPT_REG_ENABLED | USB_OPT_AUTO_PLL)"
# Create the LUFA source path variables by including the LUFA root makefile
include $(LUFA_PATH)/LUFA/makefile
# List C source files here. (C dependencies are automatically generated.)
SRC = $(TARGET).c \
$(LUFA_SRC_USB) \
$(LUFA_SRC_USBCLASS) \
$(LUFA_SRC_SERIAL)
# List C++ source files here. (C dependencies are automatically generated.)
CPPSRC =
# List Assembler source files here.
# Make them always end in a capital .S. Files ending in a lowercase .s
# will not be considered source files but generated files (assembler
# output from the compiler), and will be deleted upon "make clean"!
# Even though the DOS/Win* filesystem matches both .s and .S the same,
# it will preserve the spelling of the filenames, and gcc itself does
# care about how the name is spelled on its command-line.
ASRC =
# Optimization level, can be [0, 1, 2, 3, s].
# 0 = turn off optimization. s = optimize for size.
# (Note: 3 is not always the best optimization level. See avr-libc FAQ.)
OPT = s
# Debugging format.
# Native formats for AVR-GCC's -g are dwarf-2 [default] or stabs.
# AVR Studio 4.10 requires dwarf-2.
# AVR [Extended] COFF format requires stabs, plus an avr-objcopy run.
DEBUG = dwarf-2
# List any extra directories to look for include files here.
# Each directory must be seperated by a space.
# Use forward slashes for directory separators.
# For a directory that has spaces, enclose it in quotes.
EXTRAINCDIRS = $(LUFA_PATH)/
# Compiler flag to set the C Standard level.
# c89 = "ANSI" C
# gnu89 = c89 plus GCC extensions
# c99 = ISO C99 standard (not yet fully implemented)
# gnu99 = c99 plus GCC extensions
CSTANDARD = -std=c99
# Place -D or -U options here for C sources
CDEFS = -DF_CPU=$(F_CPU)UL
CDEFS += -DF_USB=$(F_USB)UL
CDEFS += -DBOARD=BOARD_$(BOARD) -DARCH=ARCH_$(ARCH)
CDEFS += $(LUFA_OPTS)
# Place -D or -U options here for ASM sources
ADEFS = -DF_CPU=$(F_CPU)
ADEFS += -DF_USB=$(F_USB)UL
ADEFS += -DBOARD=BOARD_$(BOARD)
ADEFS += $(LUFA_OPTS)
# Place -D or -U options here for C++ sources
CPPDEFS = -DF_CPU=$(F_CPU)UL
CPPDEFS += -DF_USB=$(F_USB)UL
CPPDEFS += -DBOARD=BOARD_$(BOARD)
CPPDEFS += $(LUFA_OPTS)
#CPPDEFS += -D__STDC_LIMIT_MACROS
#CPPDEFS += -D__STDC_CONSTANT_MACROS
#---------------- Compiler Options C ----------------
# -g*: generate debugging information
# -O*: optimization level
# -f...: tuning, see GCC manual and avr-libc documentation
# -Wall...: warning level
# -Wa,...: tell GCC to pass this to the assembler.
# -adhlns...: create assembler listing
CFLAGS = -g$(DEBUG)
CFLAGS += $(CDEFS)
CFLAGS += -O$(OPT)
CFLAGS += -funsigned-char
CFLAGS += -funsigned-bitfields
CFLAGS += -ffunction-sections
CFLAGS += -fno-inline-small-functions
CFLAGS += -fpack-struct
CFLAGS += -fshort-enums
CFLAGS += -fno-strict-aliasing
CFLAGS += -Wall
CFLAGS += -Wstrict-prototypes
#CFLAGS += -mshort-calls
#CFLAGS += -fno-unit-at-a-time
#CFLAGS += -Wundef
#CFLAGS += -Wunreachable-code
#CFLAGS += -Wsign-compare
CFLAGS += -Wa,-adhlns=$(<:%.c=$(OBJDIR)/%.lst)
CFLAGS += $(patsubst %,-I%,$(EXTRAINCDIRS))
CFLAGS += $(CSTANDARD)
#---------------- Compiler Options C++ ----------------
# -g*: generate debugging information
# -O*: optimization level
# -f...: tuning, see GCC manual and avr-libc documentation
# -Wall...: warning level
# -Wa,...: tell GCC to pass this to the assembler.
# -adhlns...: create assembler listing
CPPFLAGS = -g$(DEBUG)
CPPFLAGS += $(CPPDEFS)
CPPFLAGS += -O$(OPT)
CPPFLAGS += -funsigned-char
CPPFLAGS += -funsigned-bitfields
CPPFLAGS += -fpack-struct
CPPFLAGS += -fshort-enums
CPPFLAGS += -fno-exceptions
CPPFLAGS += -Wall
CPPFLAGS += -Wundef
#CPPFLAGS += -mshort-calls
#CPPFLAGS += -fno-unit-at-a-time
#CPPFLAGS += -Wstrict-prototypes
#CPPFLAGS += -Wunreachable-code
#CPPFLAGS += -Wsign-compare
CPPFLAGS += -Wa,-adhlns=$(<:%.cpp=$(OBJDIR)/%.lst)
CPPFLAGS += $(patsubst %,-I%,$(EXTRAINCDIRS))
#CPPFLAGS += $(CSTANDARD)
#---------------- Assembler Options ----------------
# -Wa,...: tell GCC to pass this to the assembler.
# -adhlns: create listing
# -gstabs: have the assembler create line number information; note that
# for use in COFF files, additional information about filenames
# and function names needs to be present in the assembler source
# files -- see avr-libc docs [FIXME: not yet described there]
# -listing-cont-lines: Sets the maximum number of continuation lines of hex
# dump that will be displayed for a given single line of source input.
ASFLAGS = $(ADEFS) -Wa,-adhlns=$(<:%.S=$(OBJDIR)/%.lst),-gstabs,--listing-cont-lines=100
#---------------- Library Options ----------------
# Minimalistic printf version
PRINTF_LIB_MIN = -Wl,-u,vfprintf -lprintf_min
# Floating point printf version (requires MATH_LIB = -lm below)
PRINTF_LIB_FLOAT = -Wl,-u,vfprintf -lprintf_flt
# If this is left blank, then it will use the Standard printf version.
PRINTF_LIB =
#PRINTF_LIB = $(PRINTF_LIB_MIN)
#PRINTF_LIB = $(PRINTF_LIB_FLOAT)
# Minimalistic scanf version
SCANF_LIB_MIN = -Wl,-u,vfscanf -lscanf_min
# Floating point + %[ scanf version (requires MATH_LIB = -lm below)
SCANF_LIB_FLOAT = -Wl,-u,vfscanf -lscanf_flt
# If this is left blank, then it will use the Standard scanf version.
SCANF_LIB =
#SCANF_LIB = $(SCANF_LIB_MIN)
#SCANF_LIB = $(SCANF_LIB_FLOAT)
MATH_LIB = -lm
# List any extra directories to look for libraries here.
# Each directory must be seperated by a space.
# Use forward slashes for directory separators.
# For a directory that has spaces, enclose it in quotes.
EXTRALIBDIRS =
#---------------- External Memory Options ----------------
# 64 KB of external RAM, starting after internal RAM (ATmega128!),
# used for variables (.data/.bss) and heap (malloc()).
#EXTMEMOPTS = -Wl,-Tdata=0x801100,--defsym=__heap_end=0x80ffff
# 64 KB of external RAM, starting after internal RAM (ATmega128!),
# only used for heap (malloc()).
#EXTMEMOPTS = -Wl,--section-start,.data=0x801100,--defsym=__heap_end=0x80ffff
EXTMEMOPTS =
#---------------- Linker Options ----------------
# -Wl,...: tell GCC to pass this to linker.
# -Map: create map file
# --cref: add cross reference to map file
LDFLAGS = -Wl,-Map=$(TARGET).map,--cref
LDFLAGS += -Wl,--relax
LDFLAGS += -Wl,--gc-sections
LDFLAGS += $(EXTMEMOPTS)
LDFLAGS += $(patsubst %,-L%,$(EXTRALIBDIRS))
LDFLAGS += $(PRINTF_LIB) $(SCANF_LIB) $(MATH_LIB)
#LDFLAGS += -T linker_script.x
#---------------- Programming Options (avrdude) ----------------
# Programming hardware
# Type: avrdude -c ?
# to get a full listing.
#
AVRDUDE_PROGRAMMER = jtagmkII
# com1 = serial port. Use lpt1 to connect to parallel port.
AVRDUDE_PORT = usb
AVRDUDE_WRITE_FLASH = -U flash:w:$(TARGET).hex
#AVRDUDE_WRITE_EEPROM = -U eeprom:w:$(TARGET).eep
# Uncomment the following if you want avrdude's erase cycle counter.
# Note that this counter needs to be initialized first using -Yn,
# see avrdude manual.
#AVRDUDE_ERASE_COUNTER = -y
# Uncomment the following if you do /not/ wish a verification to be
# performed after programming the device.
#AVRDUDE_NO_VERIFY = -V
# Increase verbosity level. Please use this when submitting bug
# reports about avrdude. See <http://savannah.nongnu.org/projects/avrdude>
# to submit bug reports.
#AVRDUDE_VERBOSE = -v -v
AVRDUDE_FLAGS = -p $(MCU) -P $(AVRDUDE_PORT) -c $(AVRDUDE_PROGRAMMER)
AVRDUDE_FLAGS += $(AVRDUDE_NO_VERIFY)
AVRDUDE_FLAGS += $(AVRDUDE_VERBOSE)
AVRDUDE_FLAGS += $(AVRDUDE_ERASE_COUNTER)
#---------------- Debugging Options ----------------
# For simulavr only - target MCU frequency.
DEBUG_MFREQ = $(F_CPU)
# Set the DEBUG_UI to either gdb or insight.
# DEBUG_UI = gdb
DEBUG_UI = insight
# Set the debugging back-end to either avarice, simulavr.
DEBUG_BACKEND = avarice
#DEBUG_BACKEND = simulavr
# GDB Init Filename.
GDBINIT_FILE = __avr_gdbinit
# When using avarice settings for the JTAG
JTAG_DEV = /dev/com1
# Debugging port used to communicate between GDB / avarice / simulavr.
DEBUG_PORT = 4242
# Debugging host used to communicate between GDB / avarice / simulavr, normally
# just set to localhost unless doing some sort of crazy debugging when
# avarice is running on a different computer.
DEBUG_HOST = localhost
#============================================================================
# Define programs and commands.
SHELL = sh
CC = avr-gcc
OBJCOPY = avr-objcopy
OBJDUMP = avr-objdump
SIZE = avr-size
AR = avr-ar rcs
NM = avr-nm
AVRDUDE = avrdude
REMOVE = rm -f
REMOVEDIR = rm -rf
COPY = cp
WINSHELL = cmd
# Define Messages
# English
MSG_ERRORS_NONE = Errors: none
MSG_BEGIN = -------- begin --------
MSG_END = -------- end --------
MSG_SIZE_BEFORE = Size before:
MSG_SIZE_AFTER = Size after:
MSG_COFF = Converting to AVR COFF:
MSG_EXTENDED_COFF = Converting to AVR Extended COFF:
MSG_FLASH = Creating load file for Flash:
MSG_EEPROM = Creating load file for EEPROM:
MSG_EXTENDED_LISTING = Creating Extended Listing:
MSG_SYMBOL_TABLE = Creating Symbol Table:
MSG_LINKING = Linking:
MSG_COMPILING = Compiling C:
MSG_COMPILING_CPP = Compiling C++:
MSG_ASSEMBLING = Assembling:
MSG_CLEANING = Cleaning project:
MSG_CREATING_LIBRARY = Creating library:
# Define all object files.
OBJ = $(SRC:%.c=$(OBJDIR)/%.o) $(CPPSRC:%.cpp=$(OBJDIR)/%.o) $(ASRC:%.S=$(OBJDIR)/%.o)
# Define all listing files.
LST = $(SRC:%.c=$(OBJDIR)/%.lst) $(CPPSRC:%.cpp=$(OBJDIR)/%.lst) $(ASRC:%.S=$(OBJDIR)/%.lst)
# Compiler flags to generate dependency files.
GENDEPFLAGS = -MMD -MP -MF .dep/$(@F).d
# Combine all necessary flags and optional flags.
# Add target processor to flags.
ALL_CFLAGS = -mmcu=$(MCU) -I. $(CFLAGS) $(GENDEPFLAGS)
ALL_CPPFLAGS = -mmcu=$(MCU) -I. -x c++ $(CPPFLAGS) $(GENDEPFLAGS)
ALL_ASFLAGS = -mmcu=$(MCU) -I. -x assembler-with-cpp $(ASFLAGS)
# Default target.
all: begin gccversion sizebefore build sizeafter end
# Change the build target to build a HEX file or a library.
build: elf hex eep lss sym
#build: lib
elf: $(TARGET).elf
hex: $(TARGET).hex
eep: $(TARGET).eep
lss: $(TARGET).lss
sym: $(TARGET).sym
LIBNAME=lib$(TARGET).a
lib: $(LIBNAME)
# Eye candy.
# AVR Studio 3.x does not check make's exit code but relies on
# the following magic strings to be generated by the compile job.
begin:
@echo
@echo $(MSG_BEGIN)
end:
@echo $(MSG_END)
@echo
# Display size of file.
HEXSIZE = $(SIZE) --target=$(FORMAT) $(TARGET).hex
ELFSIZE = $(SIZE) $(MCU_FLAG) $(FORMAT_FLAG) $(TARGET).elf
MCU_FLAG = $(shell $(SIZE) --help | grep -- --mcu > /dev/null && echo --mcu=$(MCU) )
FORMAT_FLAG = $(shell $(SIZE) --help | grep -- --format=.*avr > /dev/null && echo --format=avr )
sizebefore:
@if test -f $(TARGET).elf; then echo; echo $(MSG_SIZE_BEFORE); $(ELFSIZE); \
2>/dev/null; echo; fi
sizeafter:
@if test -f $(TARGET).elf; then echo; echo $(MSG_SIZE_AFTER); $(ELFSIZE); \
2>/dev/null; echo; fi
# Display compiler version information.
gccversion :
@$(CC) --version
# Program the device.
program: $(TARGET).hex $(TARGET).eep
$(AVRDUDE) $(AVRDUDE_FLAGS) $(AVRDUDE_WRITE_FLASH) $(AVRDUDE_WRITE_EEPROM)
flip: $(TARGET).hex
batchisp -hardware usb -device $(MCU) -operation erase f
batchisp -hardware usb -device $(MCU) -operation loadbuffer $(TARGET).hex program
batchisp -hardware usb -device $(MCU) -operation start reset 0
dfu: $(TARGET).hex
dfu-programmer $(MCU) erase
dfu-programmer $(MCU) flash $(TARGET).hex
dfu-programmer $(MCU) reset
flip-ee: $(TARGET).hex $(TARGET).eep
$(COPY) $(TARGET).eep $(TARGET)eep.hex
batchisp -hardware usb -device $(MCU) -operation memory EEPROM erase
batchisp -hardware usb -device $(MCU) -operation memory EEPROM loadbuffer $(TARGET)eep.hex program
batchisp -hardware usb -device $(MCU) -operation start reset 0
$(REMOVE) $(TARGET)eep.hex
dfu-ee: $(TARGET).hex $(TARGET).eep
dfu-programmer $(MCU) eeprom-flash $(TARGET).eep
dfu-programmer $(MCU) reset
# Generate avr-gdb config/init file which does the following:
# define the reset signal, load the target file, connect to target, and set
# a breakpoint at main().
gdb-config:
@$(REMOVE) $(GDBINIT_FILE)
@echo define reset >> $(GDBINIT_FILE)
@echo SIGNAL SIGHUP >> $(GDBINIT_FILE)
@echo end >> $(GDBINIT_FILE)
@echo file $(TARGET).elf >> $(GDBINIT_FILE)
@echo target remote $(DEBUG_HOST):$(DEBUG_PORT) >> $(GDBINIT_FILE)
ifeq ($(DEBUG_BACKEND),simulavr)
@echo load >> $(GDBINIT_FILE)
endif
@echo break main >> $(GDBINIT_FILE)
debug: gdb-config $(TARGET).elf
ifeq ($(DEBUG_BACKEND), avarice)
@echo Starting AVaRICE - Press enter when "waiting to connect" message displays.
@$(WINSHELL) /c start avarice --jtag $(JTAG_DEV) --erase --program --file \
$(TARGET).elf $(DEBUG_HOST):$(DEBUG_PORT)
@$(WINSHELL) /c pause
else
@$(WINSHELL) /c start simulavr --gdbserver --device $(MCU) --clock-freq \
$(DEBUG_MFREQ) --port $(DEBUG_PORT)
endif
@$(WINSHELL) /c start avr-$(DEBUG_UI) --command=$(GDBINIT_FILE)
# Convert ELF to COFF for use in debugging / simulating in AVR Studio or VMLAB.
COFFCONVERT = $(OBJCOPY) --debugging
COFFCONVERT += --change-section-address .data-0x800000
COFFCONVERT += --change-section-address .bss-0x800000
COFFCONVERT += --change-section-address .noinit-0x800000
COFFCONVERT += --change-section-address .eeprom-0x810000
coff: $(TARGET).elf
@echo
@echo $(MSG_COFF) $(TARGET).cof
$(COFFCONVERT) -O coff-avr $< $(TARGET).cof
extcoff: $(TARGET).elf
@echo
@echo $(MSG_EXTENDED_COFF) $(TARGET).cof
$(COFFCONVERT) -O coff-ext-avr $< $(TARGET).cof
# Create final output files (.hex, .eep) from ELF output file.
%.hex: %.elf
@echo
@echo $(MSG_FLASH) $@
$(OBJCOPY) -O $(FORMAT) -R .eeprom -R .fuse -R .lock $< $@
%.eep: %.elf
@echo
@echo $(MSG_EEPROM) $@
-$(OBJCOPY) -j .eeprom --set-section-flags=.eeprom="alloc,load" \
--change-section-lma .eeprom=0 --no-change-warnings -O $(FORMAT) $< $@ || exit 0
# Create extended listing file from ELF output file.
%.lss: %.elf
@echo
@echo $(MSG_EXTENDED_LISTING) $@
$(OBJDUMP) -h -S -z $< > $@
# Create a symbol table from ELF output file.
%.sym: %.elf
@echo
@echo $(MSG_SYMBOL_TABLE) $@
$(NM) -n $< > $@
# Create library from object files.
.SECONDARY : $(TARGET).a
.PRECIOUS : $(OBJ)
%.a: $(OBJ)
@echo
@echo $(MSG_CREATING_LIBRARY) $@
$(AR) $@ $(OBJ)
# Link: create ELF output file from object files.
.SECONDARY : $(TARGET).elf
.PRECIOUS : $(OBJ)
%.elf: $(OBJ)
@echo
@echo $(MSG_LINKING) $@
$(CC) $(ALL_CFLAGS) $^ --output $@ $(LDFLAGS)
# Compile: create object files from C source files.
$(OBJDIR)/%.o : %.c
@echo
@echo $(MSG_COMPILING) $<
$(CC) -c $(ALL_CFLAGS) $< -o $@
# Compile: create object files from C++ source files.
$(OBJDIR)/%.o : %.cpp
@echo
@echo $(MSG_COMPILING_CPP) $<
$(CC) -c $(ALL_CPPFLAGS) $< -o $@
# Compile: create assembler files from C source files.
%.s : %.c
$(CC) -S $(ALL_CFLAGS) $< -o $@
# Compile: create assembler files from C++ source files.
%.s : %.cpp
$(CC) -S $(ALL_CPPFLAGS) $< -o $@
# Assemble: create object files from assembler source files.
$(OBJDIR)/%.o : %.S
@echo
@echo $(MSG_ASSEMBLING) $<
$(CC) -c $(ALL_ASFLAGS) $< -o $@
# Create preprocessed source for use in sending a bug report.
%.i : %.c
$(CC) -E -mmcu=$(MCU) -I. $(CFLAGS) $< -o $@
# Target: clean project.
clean: begin clean_list end
clean_list :
@echo
@echo $(MSG_CLEANING)
$(REMOVE) $(TARGET).hex
$(REMOVE) $(TARGET).eep
$(REMOVE) $(TARGET).cof
$(REMOVE) $(TARGET).elf
$(REMOVE) $(TARGET).map
$(REMOVE) $(TARGET).sym
$(REMOVE) $(TARGET).lss
$(REMOVE) $(SRC:%.c=$(OBJDIR)/%.o) $(CPPSRC:%.cpp=$(OBJDIR)/%.o) $(ASRC:%.S=$(OBJDIR)/%.o)
$(REMOVE) $(SRC:%.c=$(OBJDIR)/%.lst) $(CPPSRC:%.cpp=$(OBJDIR)/%.lst) $(ASRC:%.S=$(OBJDIR)/%.lst)
$(REMOVE) $(SRC:.c=.s)
$(REMOVE) $(SRC:.c=.d)
$(REMOVE) $(SRC:.c=.i)
$(REMOVEDIR) .dep
doxygen:
@echo Generating Project Documentation...
@doxygen Doxygen.conf
@echo Documentation Generation Complete.
clean_doxygen:
rm -rf Documentation
# Create object files directory
$(shell mkdir $(OBJDIR) 2>/dev/null)
# Include the dependency files.
-include $(shell mkdir .dep 2>/dev/null) $(wildcard .dep/*)
# Listing of phony targets.
.PHONY : all begin finish end sizebefore sizeafter gccversion \
build elf hex eep lss sym coff extcoff doxygen clean \
clean_list clean_doxygen program dfu flip flip-ee dfu-ee \
debug gdb-config
Loading…
Cancel
Save