Moved all source to the trunk directory.

pull/1469/head
Dean Camera 16 years ago
parent 6a10d6b465
commit 032a83e9e1

@ -0,0 +1,176 @@
Instructions for converting the LUFA USBtoSerial Demo to an AVR ISP Programmer.
By Opendous Inc., Copyright under the Creative Commons Attribution License:
http://creativecommons.org/licenses/by/3.0/
1) Start with the LUFA/Demos/USBtoSerial firmware.
- rename USBtoSerial.c, USBtoSerial.h, and USBtoSerial.aps to
AVRISP_Programmer.*
- edit AVRISP_Programmer.aps and rename all instances of "USBtoSerial" to
"AVRISP_Programmer"
- copy AVRISP_Programmer.txt from an older version of AVRISP_Programmer
2) Edit makefile by changing TARGET from "USBtoSerial" to "AVRISP_Programmer"
3) Edit AVRISP_Programmer.h:
- change ifdef _USB_TO_SERIAL_H to _AVRISP_PROGRAMMER_H_
- rename ReconfigureUSART(void) to ReconfigureSPI(void)
- add void processHostSPIRequest(void); & void delay_ms(uint8_t dly);
- replace the define for Serial.h with one for SPI.h:
#include <libs/LUFA/Drivers/AT90USBXXX/SPI.h>
4) Make alterations to Descriptors.c
- change manufacturer string to "www.AVRopendous.org", length=19
- change product string to "LUFA-Based AVR ISP Programmer", length=29
5) Edit Ringbuff.h to enable the Peek Command: #define BUFF_USEPEEK
6) Edit AVRISP_Programmer.c:
- change #include "USBtoSerial.h" to #include "AVRISP_Programmer.h"
- change BUTTLOADTAG(ProjName to "LUFA AVR910 ISP Programmer"
- in main(), rename ReconfigureUSART() to Reconfigure();
- in EVENT_HANDLER(USB_UnhandledControlPacket), rename ReconfigureUSART
- delete the ISRs: ISR(USART1_RX_vect) & ISR(USART1_TX_vect)
- delete ReconfigureUSART(void)
- add void ReconfigureSPI(void), void processHostSPIRequest(void),
and void delay_ms(uint8_t dly) from a previous version
- add Timer1 and SPI initialization code to main():
/* Hardware Initialization */
//LEDs_Init();
DDRB = 0;
PORTB = 0;
DDRC |= ((1 << PC2) | (1 << PC4) | (1 << PC5) | (1 << PC6) | (1 << PC7)); //AT90USBxx2
// PC2 is also used for RESET, so set it HIGH initially - note 'P' command sets it to LOW (Active)
PORTC |= ((1 << PC2) | (1 << PC4) | (1 << PC5) | (1 << PC6) | (1 << PC7)); //AT90USBxx2
DDRD = 0;
PORTD = (1 << PB7); // only PB7(HWB) should be High as this is the bootloader pin
// Prepare PortB for SPI - set PB0(^SS), PB1(SCK), PB2(MOSI) as output as well as all other pins except PB3(MISO)
DDRB = (1 << PB0) | (1 << PB1) | (1 << PB2) | (0 << PB3) | (1 << PB4) | (1 << PB5) | (1 << PB6) | (1 << PB7);
PORTB |= (1 << PB0);
// initialize Timer1 for use in delay function
TCCR1A = 0;
//TCCR1B = (1 << CS10); // no prescaling, use CLK
TCCR1B = ((1 << CS12) | (1 << CS10)); // prescale by CLK/1024
// 8MHz/1024 = 7813 ticks per second --> ~8 ticks per millisecond (ms)
timerval = TCNT1; // start timer1
- In TASK(CDC_Task) in the
if (USB_IsConnected) {
if (Endpoint_ReadWriteAllowed()) {
while (Endpoint_BytesInEndpoint()) {
...
structure, after Buffer_StoreElement(&Rx_Buffer, Endpoint_Read_Byte()):
/* Each time there is an element, check which comand should be
run and if enough data is available to run that command.
There are 1-byte, 2-byte, 3-byte, 4-byte commands, and 5-byte commands
Remember that the "which command" byte counts as 1 */
if (Rx_Buffer.Elements == 0) {
// do nothing, wait for data
} else {
tempByte = Buffer_PeekElement(&Rx_Buffer); // peek at first element
/* make sure the issued command and associated data are all ready */
if (Rx_Buffer.Elements == 1) { // zero data byte command
if ((tempByte == 'P') | (tempByte == 'a') | (tempByte == 'm') |
(tempByte == 'R') | (tempByte == 'd') | (tempByte == 'e') |
(tempByte == 'L') | (tempByte == 's') | (tempByte == 't') |
(tempByte == 'S') | (tempByte == 'V') | (tempByte == 'v') |
(tempByte == 'p') | (tempByte == 'F')) {
processHostSPIRequest(); // command has enough data, process it
}
} else if (Rx_Buffer.Elements == 2) { // one data byte command
if ((tempByte == 'T') | (tempByte == 'c') | (tempByte == 'C') |
(tempByte == 'D') | (tempByte == 'l') | (tempByte == 'f') |
(tempByte == 'x') | (tempByte == 'y')) {
processHostSPIRequest(); // command has enough data, process it
}
} else if (Rx_Buffer.Elements == 3) { // two data byte command
if ((tempByte == 'A') | (tempByte == 'Z')) {
processHostSPIRequest(); // command has enough data, process it
}
} else if (Rx_Buffer.Elements == 4) { // three data byte command
if ((tempByte == ':')) {
processHostSPIRequest(); // command has enough data, process it
}
} else if (Rx_Buffer.Elements == 5) { // four data byte command
if ((tempByte == '.')) {
processHostSPIRequest(); // command has enough data, process it
}
} else {
// do nothing
}
}
- need to add code to flush the buffer. Change:
/* Check if Rx buffer contains data */
if (Rx_Buffer.Elements)
{
/* Initiate the transmission of the buffer contents if USART idle*/
if (!(Transmitting))
{
Transmitting = true;
Serial_TxByte(Buffer_GetElement(&Rx_Buffer));
}
}
To:
/* Check if Rx buffer contains data */
if (Rx_Buffer.Elements)
{
/* Initiate the transmission of the buffer contents if USART idle*/
if (!(Transmitting))
{
Transmitting = true;
/* The following flushes the receive buffer to prepare for new
data and commands. Need to flush the buffer as the command
byte which is peeked above needs to be dealt with, otherwise
the command bytes will overflow the buffer eventually */
//Buffer_GetElement(&Rx_Buffer); // also works
Buffer_Initialize(&Rx_Buffer);
}
}
- need to add the following defines and globals:
#define RESETPORT PORTB
#define RESETPIN PB0
#define RESETPORT2 PORTC
#define RESETPIN2 PC2
#define CR_HEX '\r'
#define DELAY_VERYSHORT 0x01
#define DELAY_SHORT 0x02
#define DELAY_MEDIUM 0x03
#define DELAY_LONG 0x05
#define DELAY_MULTIPLE 0x04
/* AVR Device Codes - Can have a maximum of 14 but can be any you want.
Note that these are completely irrelevent. If AVRdude supports a
device, then that device is programmable. Use -F switch to ignore
device codes. */
#define AVRDEVCODE01 0x55 /* ATtiny12 */
#define AVRDEVCODE02 0x56 /* ATtiny15 */
#define AVRDEVCODE03 0x5E /* ATtiny261 */
#define AVRDEVCODE04 0x76 /* ATmega8 */
#define AVRDEVCODE05 0x74 /* ATmega16 */
#define AVRDEVCODE06 0x72 /* ATmega32 */
#define AVRDEVCODE07 0x45 /* ATmega64 */
#define AVRDEVCODE08 0x74 /* ATmega644 */
#define AVRDEVCODE09 0x43 /* ATmega128 */
#define AVRDEVCODE10 0x63 /* ATmega162 */
#define AVRDEVCODE11 0x78 /* ATmega169 */
#define AVRDEVCODE12 0x6C /* AT90S4434 */
#define AVRDEVCODE13 0x38 /* AT90S8515A */
#define AVRDEVCODE14 0x65 /* AT90S8555 */
/* some global variables used throughout */
uint8_t tempIOreg = 0;
uint8_t tempIOreg2 = 0;
uint8_t tempIOreg3 = 0;
uint8_t tempIOreg4 = 0;
uint8_t dataWidth = 0;
uint8_t firstRun = 1;
uint8_t deviceCode = 0;
uint8_t tempByte = 0;
uint16_t currAddress = 0;
uint16_t timerval = 0;

@ -0,0 +1 @@
<AVRStudio><MANAGEMENT><ProjectName>AVRISP_Programmer</ProjectName><Created>30-Sep-2008 14:18:39</Created><LastEdit>30-Sep-2008 14:18:52</LastEdit><ICON>241</ICON><ProjectType>0</ProjectType><Created>30-Sep-2008 14:18:39</Created><Version>4</Version><Build>4, 14, 0, 589</Build><ProjectTypeName>AVR GCC</ProjectTypeName></MANAGEMENT><CODE_CREATION><ObjectFile></ObjectFile><EntryFile></EntryFile><SaveFolder>C:\Users\Dean\Documents\Electronics\Projects\WORK\MyUSBWORK\Demos\AVRISP_Programmer\</SaveFolder></CODE_CREATION><DEBUG_TARGET><CURRENT_TARGET></CURRENT_TARGET><CURRENT_PART></CURRENT_PART><BREAKPOINTS></BREAKPOINTS><IO_EXPAND><HIDE>false</HIDE></IO_EXPAND><REGISTERNAMES><Register>R00</Register><Register>R01</Register><Register>R02</Register><Register>R03</Register><Register>R04</Register><Register>R05</Register><Register>R06</Register><Register>R07</Register><Register>R08</Register><Register>R09</Register><Register>R10</Register><Register>R11</Register><Register>R12</Register><Register>R13</Register><Register>R14</Register><Register>R15</Register><Register>R16</Register><Register>R17</Register><Register>R18</Register><Register>R19</Register><Register>R20</Register><Register>R21</Register><Register>R22</Register><Register>R23</Register><Register>R24</Register><Register>R25</Register><Register>R26</Register><Register>R27</Register><Register>R28</Register><Register>R29</Register><Register>R30</Register><Register>R31</Register></REGISTERNAMES><COM>Auto</COM><COMType>0</COMType><WATCHNUM>0</WATCHNUM><WATCHNAMES><Pane0></Pane0><Pane1></Pane1><Pane2></Pane2><Pane3></Pane3></WATCHNAMES><BreakOnTrcaeFull>0</BreakOnTrcaeFull></DEBUG_TARGET><Debugger><Triggers></Triggers></Debugger><AVRGCCPLUGIN><FILES><SOURCEFILE>Descriptors.c</SOURCEFILE><SOURCEFILE>RingBuff.c</SOURCEFILE><SOURCEFILE>AVRISP_Programmer.c</SOURCEFILE><HEADERFILE>Descriptors.h</HEADERFILE><HEADERFILE>RingBuff.h</HEADERFILE><HEADERFILE>AVRISP_Programmer.h</HEADERFILE><OTHERFILE>makefile</OTHERFILE></FILES><CONFIGS><CONFIG><NAME>default</NAME><USESEXTERNALMAKEFILE>YES</USESEXTERNALMAKEFILE><EXTERNALMAKEFILE>makefile</EXTERNALMAKEFILE><PART>atmega128</PART><HEX>1</HEX><LIST>1</LIST><MAP>1</MAP><OUTPUTFILENAME>AVRISP_Programmer.elf</OUTPUTFILENAME><OUTPUTDIR>default\</OUTPUTDIR><ISDIRTY>1</ISDIRTY><OPTIONS/><INCDIRS/><LIBDIRS/><LIBS/><LINKOBJECTS/><OPTIONSFORALL>-Wall -gdwarf-2 -std=gnu99 -Os -funsigned-char -funsigned-bitfields -fpack-struct -fshort-enums</OPTIONSFORALL><LINKEROPTIONS></LINKEROPTIONS><SEGMENTS/></CONFIG></CONFIGS><LASTCONFIG>default</LASTCONFIG><USES_WINAVR>1</USES_WINAVR><GCC_LOC>C:\WinAVR-20080512\bin\avr-gcc.exe</GCC_LOC><MAKE_LOC>C:\WinAVR-20080512\utils\bin\make.exe</MAKE_LOC></AVRGCCPLUGIN><IOView><usergroups/><sort sorted="0" column="0" ordername="0" orderaddress="0" ordergroup="0"/></IOView><Files></Files><Events><Bookmarks></Bookmarks></Events><Trace><Filters></Filters></Trace></AVRStudio>

@ -0,0 +1,886 @@
/*
LUFA Library
Copyright (C) Dean Camera, 2009.
dean [at] fourwalledcubicle [dot] com
www.fourwalledcubicle.com
*/
/*
Copyright 2009 Dean Camera (dean [at] fourwalledcubicle [dot] com)
AVR ISP Programmer code Copyright 2009 Opendous Inc. (www.opendous.org)
For more info and usage instructions for this firmware, visit:
http://code.google.com/p/avropendous/wiki/AVR_ISP_Programmer
Note that this firmware is designed to work with AVRdude:
http://savannah.nongnu.org/projects/avrdude
But should work with other software that supports the AVR910 ISP
programmer or STK200 hardware.
Permission to use, copy, modify, and distribute this software
and its documentation for any purpose and without fee is hereby
granted, provided that the above copyright notice appear in all
copies and that both that the copyright notice and this
permission notice and warranty disclaimer appear in supporting
documentation, and that the name of the author not be used in
advertising or publicity pertaining to distribution of the
software without specific, written prior permission.
The author disclaim all warranties with regard to this
software, including all implied warranties of merchantability
and fitness. In no event shall the author be liable for any
special, indirect or consequential damages or any damages
whatsoever resulting from loss of use, data or profits, whether
in an action of contract, negligence or other tortious action,
arising out of or in connection with the use or performance of
this software.
*/
/*
Usage:
avrdude -vv -F -P COM7 -c avr910 -p t261
Note -F flag which overrides signature check and enables programming
of any "In-System Programmable via SPI Port" AVR MCU. Part number,
t261, should be set to your target device.
avrdude -vv -F -P COM7 -c avr910 -p t261 -U flash:w:PROG.hex
PROG.hex is the hex file to program your t261 AVR with
avrdude -vv -F -P COM7 -b 115200 -c avr910 -p t261 -U flash:w:test.hex
The -b 115200 sets the SPI clock to 62.5kHz from the default 125kHz and may
work when the default programming speed fails.
AVROSP.exe -dATtiny261 -cCOM7 -rf
AVRosp is the Open Source AVR ISP Programming Software available from Atmel.com
Note: on Linux systems, COM7 should be replaced with someting like /dev/ttyACM0
You can determine this value by running dmesg after plugging in the device
Note: you must RESET the programmer after each use (AVRdude session).
Note: If you experience errors with older devices, try changing the DELAY defines
MISO, MOSI, and SCK are connected directly from the AVRopendous board
to the pin of the same functionality on the target. RESET pin on the target
can be connected either to SS (PB0), or PC2. Do not have any other pins
connected - especially HWB pin, to avoid unintentional behaviour.
AVR910 functionality was overlayed on USBtoSerial functionality.
Keep this in mind when looking over the code.
Default target speed is 125kHz and corresponds to 19200 baud, which
is the default setting for AVRdude.
Changing "Baud-Rate" will change the SPI speed. Defualt SPI clock speed
is 8Mhz / 4 = 2MHz. 8Mhz is the device clock speed. This is the setting at
9600 baud. The following is a table of baud-rate vs. SPI Speed that will result
9600 = 2Mhz
14400 = 1MHz
19200 = 125kHz (AVRdude Default)
38400 = 250kHz
57600 = 500kHz
115200 = 62.5kHz
Before running, you will need to install the INF file that
is located in the project directory. This will enable
Windows to use its inbuilt CDC drivers, negating the need
for special Windows drivers for the device. To install,
right-click the .INF file and choose the Install option.
*/
/* TODO: - fix the requirement that a RESET must be performed after each session, which
is only an issue under Windows. Everything works fine under Linux
*/
#include "AVRISP_Programmer.h"
/* Project Tags, for reading out using the ButtLoad project */
BUTTLOADTAG(ProjName, "LUFA AVR910 ISP Programmer");
BUTTLOADTAG(BuildTime, __TIME__);
BUTTLOADTAG(BuildDate, __DATE__);
BUTTLOADTAG(LUFAVersion, "LUFA V" LUFA_VERSION_STRING);
#define RESETPORT PORTB
#define RESETPIN PB0
#define RESETPORT2 PORTC
#define RESETPIN2 PC2
#define CR_HEX '\r'
#define DELAY_VERYSHORT 0x01
#define DELAY_SHORT 0x02
#define DELAY_MEDIUM 0x03
#define DELAY_LONG 0x05
#define DELAY_MULTIPLE 0x02
/* AVR Device Codes - Can have a maximum of 14 but can be any you want.
Note that these are completely irrelevent. If AVRdude supports a device,
then that device is programmable. Use -F switch to ignore device codes. */
#define AVRDEVCODE01 0x55 /* ATtiny12 */
#define AVRDEVCODE02 0x56 /* ATtiny15 */
#define AVRDEVCODE03 0x5E /* ATtiny261 */
#define AVRDEVCODE04 0x76 /* ATmega8 */
#define AVRDEVCODE05 0x74 /*ATmega16 */
#define AVRDEVCODE06 0x72 /* ATmega32 */
#define AVRDEVCODE07 0x45 /* ATmega64 */
#define AVRDEVCODE08 0x74 /* ATmega644 */
#define AVRDEVCODE09 0x43 /* ATmega128 */
#define AVRDEVCODE10 0x63 /* ATmega162 */
#define AVRDEVCODE11 0x78 /* ATmega169 */
#define AVRDEVCODE12 0x6C /* AT90S4434 */
#define AVRDEVCODE13 0x38 /* AT90S8515A */
#define AVRDEVCODE14 0x65 /* AT90S8555 */
/* Scheduler Task List */
TASK_LIST
{
{ Task: USB_USBTask , TaskStatus: TASK_STOP },
{ Task: CDC_Task , TaskStatus: TASK_STOP },
};
/* Globals: */
/** Contains the current baud rate and other settings of the virtual serial port.
*
These values are set by the host via a class-specific request, and the physical USART should be reconfigured to match the
new settings each time they are changed by the host.
*/
CDC_Line_Coding_t LineCoding = { BaudRateBPS: 9600,
CharFormat: OneStopBit,
ParityType: Parity_None,
DataBits: 8 };
/** Ring (circular) buffer to hold the RX data - data from the host to the attached device on the serial port. */
RingBuff_t Rx_Buffer;
/** Ring (circular) buffer to hold the TX data - data from the attached device on the serial port to the host. */
RingBuff_t Tx_Buffer;
/** Flag to indicate if the USART is currently transmitting data from the Rx_Buffer circular buffer. */
volatile bool Transmitting = false;
/* some global variables used throughout */
uint8_t tempIOreg = 0;
uint8_t tempIOreg2 = 0;
uint8_t tempIOreg3 = 0;
uint8_t tempIOreg4 = 0;
uint8_t dataWidth = 0;
uint8_t firstRun = 1;
uint8_t deviceCode = 0;
uint8_t tempByte = 0;
uint16_t currAddress = 0;
uint16_t timerval = 0;
/** Main program entry point. This routine configures the hardware required by the application, then
starts the scheduler to run the application tasks.
*/
int main(void)
{
/* Disable watchdog if enabled by bootloader/fuses */
MCUSR &= ~(1 << WDRF);
wdt_disable();
/* Disable Clock Division */
SetSystemClockPrescaler(0);
/* Hardware Initialization */
LEDs_Init();
ReconfigureSPI();
// prepare PortB
DDRB = 0;
PORTB = 0;
DDRC |= ((1 << PC2) | (1 << PC4) | (1 << PC5) | (1 << PC6) | (1 << PC7)); //AT90USBxx2
// PC2 is also used for RESET, so set it HIGH initially - note 'P' command sets it to LOW (Active)
PORTC |= ((1 << PC2) | (1 << PC4) | (1 << PC5) | (1 << PC6) | (1 << PC7)); //AT90USBxx2
DDRD = 0;
PORTD = (1 << PB7); // only PB7(HWB) should be High as this is the bootloader pin
// Prepare PortB for SPI - set PB0(^SS), PB1(SCK), PB2(MOSI) as output as well as all other pins except PB3(MISO)
DDRB = (1 << PB0) | (1 << PB1) | (1 << PB2) | (0 << PB3) | (1 << PB4) | (1 << PB5) | (1 << PB6) | (1 << PB7);
PORTB |= (1 << PB0);
// make sure DataFlash devices to not interfere - deselect them by setting PE0 and PE1 HIGH:
PORTE = 0xFF;
DDRE = 0xFF;
// initialize Timer1 for use in delay function
TCCR1A = 0;
//TCCR1B = (1 << CS10); // no prescaling, use CLK
TCCR1B = ((1 << CS12) | (1 << CS10)); // prescale by CLK/1024
// 8MHz/1024 = 7813 ticks per second --> ~8 ticks per millisecond (ms)
timerval = TCNT1; // start timer1
/* Ringbuffer Initialization */
Buffer_Initialize(&Rx_Buffer);
Buffer_Initialize(&Tx_Buffer);
/* Indicate USB not ready */
UpdateStatus(Status_USBNotReady);
/* Initialize Scheduler so that it can be used */
Scheduler_Init();
/* Initialize USB Subsystem */
USB_Init();
/* Scheduling - routine never returns, so put this last in the main function */
Scheduler_Start();
}
/** Event handler for the USB_Connect event. This indicates that the device is enumerating via the status LEDs and
starts the library USB task to begin the enumeration and USB management process.
*/
EVENT_HANDLER(USB_Connect)
{
/* Start USB management task */
Scheduler_SetTaskMode(USB_USBTask, TASK_RUN);
/* Indicate USB enumerating */
UpdateStatus(Status_USBEnumerating);
}
/** Event handler for the USB_Disconnect event. This indicates that the device is no longer connected to a host via
the status LEDs and stops the USB management and CDC management tasks.
*/
EVENT_HANDLER(USB_Disconnect)
{
/* Stop running CDC and USB management tasks */
Scheduler_SetTaskMode(CDC_Task, TASK_STOP);
Scheduler_SetTaskMode(USB_USBTask, TASK_STOP);
/* Indicate USB not ready */
UpdateStatus(Status_USBNotReady);
}
/** Event handler for the USB_ConfigurationChanged event. This is fired when the host set the current configuration
of the USB device after enumeration - the device endpoints are configured and the CDC management task started.
*/
EVENT_HANDLER(USB_ConfigurationChanged)
{
/* Setup CDC Notification, Rx and Tx Endpoints */
Endpoint_ConfigureEndpoint(CDC_NOTIFICATION_EPNUM, EP_TYPE_INTERRUPT,
ENDPOINT_DIR_IN, CDC_NOTIFICATION_EPSIZE,
ENDPOINT_BANK_SINGLE);
Endpoint_ConfigureEndpoint(CDC_TX_EPNUM, EP_TYPE_BULK,
ENDPOINT_DIR_IN, CDC_TXRX_EPSIZE,
ENDPOINT_BANK_SINGLE);
Endpoint_ConfigureEndpoint(CDC_RX_EPNUM, EP_TYPE_BULK,
ENDPOINT_DIR_OUT, CDC_TXRX_EPSIZE,
ENDPOINT_BANK_SINGLE);
/* Indicate USB connected and ready */
UpdateStatus(Status_USBReady);
/* Start CDC task */
Scheduler_SetTaskMode(CDC_Task, TASK_RUN);
}
/** Event handler for the USB_UnhandledControlPacket event. This is used to catch standard and class specific
control requests that are not handled internally by the USB library (including the CDC control commands,
which are all issued via the control endpoint), so that they can be handled appropriately for the application.
*/
EVENT_HANDLER(USB_UnhandledControlPacket)
{
uint8_t* LineCodingData = (uint8_t*)&LineCoding;
/* Process CDC specific control requests */
switch (bRequest)
{
case REQ_GetLineEncoding:
if (bmRequestType == (REQDIR_DEVICETOHOST | REQTYPE_CLASS | REQREC_INTERFACE))
{
/* Acknowedge the SETUP packet, ready for data transfer */
Endpoint_ClearSetupReceived();
/* Write the line coding data to the control endpoint */
Endpoint_Write_Control_Stream_LE(LineCodingData, sizeof(LineCoding));
/* Finalize the stream transfer to send the last packet or clear the host abort */
Endpoint_ClearSetupOUT();
}
break;
case REQ_SetLineEncoding:
if (bmRequestType == (REQDIR_HOSTTODEVICE | REQTYPE_CLASS | REQREC_INTERFACE))
{
/* Acknowedge the SETUP packet, ready for data transfer */
Endpoint_ClearSetupReceived();
/* Read the line coding data in from the host into the global struct */
Endpoint_Read_Control_Stream_LE(LineCodingData, sizeof(LineCoding));
/* Finalize the stream transfer to clear the last packet from the host */
Endpoint_ClearSetupIN();
/* Reconfigure the USART with the new settings */
ReconfigureSPI();
}
break;
case REQ_SetControlLineState:
if (bmRequestType == (REQDIR_HOSTTODEVICE | REQTYPE_CLASS | REQREC_INTERFACE))
{
#if 0
/* NOTE: Here you can read in the line state mask from the host, to get the current state of the output handshake
lines. The mask is read in from the wValue parameter, and can be masked against the CONTROL_LINE_OUT_* masks
to determine the RTS and DTR line states using the following code:
*/
uint16_t wIndex = Endpoint_Read_Word_LE();
// Do something with the given line states in wIndex
#endif
/* Acknowedge the SETUP packet, ready for data transfer */
Endpoint_ClearSetupReceived();
/* Send an empty packet to acknowedge the command */
Endpoint_ClearSetupIN();
}
break;
}
}
/** Task to manage CDC data transmission and reception to and from the host, from and to the physical USART. */
TASK(CDC_Task)
{
if (USB_IsConnected)
{
#if 0
/* NOTE: Here you can use the notification endpoint to send back line state changes to the host, for the special RS-232
handshake signal lines (and some error states), via the CONTROL_LINE_IN_* masks and the following code:
*/
USB_Notification_Header_t Notification = (USB_Notification_Header_t)
{
NotificationType: (REQDIR_DEVICETOHOST | REQTYPE_CLASS | REQREC_INTERFACE),
Notification: NOTIF_SerialState,
wValue: 0,
wIndex: 0,
wLength: sizeof(uint16_t),
};
uint16_t LineStateMask;
// Set LineStateMask here to a mask of CONTROL_LINE_IN_* masks to set the input handshake line states to send to the host
Endpoint_SelectEndpoint(CDC_NOTIFICATION_EPNUM);
Endpoint_Write_Stream_LE(&Notification, sizeof(Notification));
Endpoint_Write_Stream_LE(&LineStateMask, sizeof(LineStateMask));
Endpoint_ClearCurrentBank();
#endif
/* Select the Serial Rx Endpoint */
Endpoint_SelectEndpoint(CDC_RX_EPNUM);
if (Endpoint_ReadWriteAllowed())
{
/* Read the received data endpoint into the transmission buffer */
while (Endpoint_BytesInEndpoint())
{
/* Wait until the buffer has space for a new character */
while (!((BUFF_STATICSIZE - Rx_Buffer.Elements)));
/* Store each character from the endpoint */
Buffer_StoreElement(&Rx_Buffer, Endpoint_Read_Byte());
/* Each time there is an element, check which comand should be
run and if enough data is available to run that command.
There are 1-byte, 2-byte, 3-byte, 4-byte commands, and 5-byte commands
Remember that the "which command" byte counts as 1 */
if (Rx_Buffer.Elements == 0) {
// do nothing, wait for data
} else {
tempByte = Buffer_PeekElement(&Rx_Buffer); // peek at first element
/* make sure the issued command and associated data are all ready */
if (Rx_Buffer.Elements == 1) { // zero data byte command
if ((tempByte == 'P') | (tempByte == 'a') | (tempByte == 'm') |
(tempByte == 'R') | (tempByte == 'd') | (tempByte == 'e') |
(tempByte == 'L') | (tempByte == 's') | (tempByte == 't') |
(tempByte == 'S') | (tempByte == 'V') | (tempByte == 'v') |
(tempByte == 'p') | (tempByte == 'F')) {
processHostSPIRequest(); // command has enough data, process it
}
} else if (Rx_Buffer.Elements == 2) { // one data byte command
if ((tempByte == 'T') | (tempByte == 'c') | (tempByte == 'C') |
(tempByte == 'D') | (tempByte == 'l') | (tempByte == 'f') |
(tempByte == 'x') | (tempByte == 'y')) {
processHostSPIRequest(); // command has enough data, process it
}
} else if (Rx_Buffer.Elements == 3) { // two data byte command
if ((tempByte == 'A') | (tempByte == 'Z')) {
processHostSPIRequest(); // command has enough data, process it
}
} else if (Rx_Buffer.Elements == 4) { // three data byte command
if ((tempByte == ':')) {
processHostSPIRequest(); // command has enough data, process it
}
} else if (Rx_Buffer.Elements == 5) { // four data byte command
if ((tempByte == '.')) {
processHostSPIRequest(); // command has enough data, process it
}
} else {
// do nothing
}
}
}
/* Clear the endpoint buffer */
Endpoint_ClearCurrentBank();
}
/* Check if Rx buffer contains data */
if (Rx_Buffer.Elements)
{
/* Initiate the transmission of the buffer contents if USART idle */
if (!(Transmitting))
{
Transmitting = true;
/* The following flushes the receive buffer to prepare for new data and commands */
/* Need to flush the buffer as the command byte which is peeked above needs to be */
/* dealt with, otherwise the command bytes will overflow the buffer eventually */
//Buffer_GetElement(&Rx_Buffer); // works also
Buffer_Initialize(&Rx_Buffer);
}
}
/* Select the Serial Tx Endpoint */
Endpoint_SelectEndpoint(CDC_TX_EPNUM);
/* Check if the Tx buffer contains anything to be sent to the host */
if (Tx_Buffer.Elements)
{
/* Wait until Serial Tx Endpoint Ready for Read/Write */
while (!(Endpoint_ReadWriteAllowed()));
/* Check before sending the data if the endpoint is completely full */
bool IsFull = (Endpoint_BytesInEndpoint() == CDC_TXRX_EPSIZE);
/* Write the transmission buffer contents to the received data endpoint */
while (Tx_Buffer.Elements && (Endpoint_BytesInEndpoint() < CDC_TXRX_EPSIZE))
Endpoint_Write_Byte(Buffer_GetElement(&Tx_Buffer));
/* Send the data */
Endpoint_ClearCurrentBank();
/* If a full endpoint was sent, we need to send an empty packet afterwards to terminate the transfer */
if (IsFull)
{
/* Wait until Serial Tx Endpoint Ready for Read/Write */
while (!(Endpoint_ReadWriteAllowed()));
/* Send an empty packet to terminate the transfer */
Endpoint_ClearCurrentBank();
}
}
}
}
/** Function to manage status updates to the user. This is done via LEDs on the given board, if available, but may be changed to
log to a serial port, or anything else that is suitable for status updates.
*
\param CurrentStatus Current status of the system, from the USBtoSerial_StatusCodes_t enum
*/
void UpdateStatus(uint8_t CurrentStatus)
{
uint8_t LEDMask = LEDS_NO_LEDS;
/* Set the LED mask to the appropriate LED mask based on the given status code */
switch (CurrentStatus)
{
case Status_USBNotReady:
LEDMask = (LEDS_LED1);
break;
case Status_USBEnumerating:
LEDMask = (LEDS_LED1 | LEDS_LED2);
break;
case Status_USBReady:
LEDMask = (LEDS_LED2 | LEDS_LED4);
break;
}
/* Set the board LEDs to the new LED mask */
LEDs_SetAllLEDs(LEDMask);
}
/** Reconfigures SPI to match the current serial port settings issued by the host. */
void ReconfigureSPI(void)
{
uint8_t SPCRmask = (1 << SPE) | (1 << MSTR); // always enable SPI as Master
uint8_t SPSRmask = 0;
/* Determine data width */
if (LineCoding.ParityType == Parity_Odd) {
dataWidth = 16;
} else if (LineCoding.ParityType == Parity_Even) {
dataWidth = 32;
} else if (LineCoding.ParityType == Parity_None) {
dataWidth = 8;
}
/* Determine stop bits - 1.5 stop bits is set as 1 stop bit due to hardware limitations */
/* For SPI, determine whether format is LSB or MSB */
if (LineCoding.CharFormat == TwoStopBits) {
SPCRmask |= (1 << DORD);
} else if (LineCoding.CharFormat == OneStopBit) {
SPCRmask |= (0 << DORD);
}
/* Determine data size - 5, 6, 7, or 8 bits are supported */
/* Changing line coding changes SPI Mode
CPOL=0, CPHA=0 Sample (Rising) Setup (Falling) SPI-Mode0 == 8 bits line coding
CPOL=0, CPHA=1 Setup (Rising) Sample (Falling) SPI-Mode1 == 7 bits line coding
CPOL=1, CPHA=0 Sample (Falling) Setup (Rising) SPI-Mode2 == 6 bits line coding
CPOL=1, CPHA=1 Setup (Falling) Sample (Rising) SPI-Mode3 == 5 bits line coding
*/
if (LineCoding.DataBits == 5) {
SPCRmask |= ((1 << CPOL) | (1 << CPHA));
} else if (LineCoding.DataBits == 6) {
SPCRmask |= ((1 << CPOL) | (0 << CPHA));
} else if (LineCoding.DataBits == 7) {
SPCRmask |= ((0 << CPOL) | (1 << CPHA));
} else if (LineCoding.DataBits == 8) {
SPCRmask |= ((0 << CPOL) | (0 << CPHA));
}
/* Set the USART baud rate register to the desired baud rate value */
/* also alter the SPI speed via value of baud rate */
if (LineCoding.BaudRateBPS == 9600) { // 2Mhz SPI (Fosc / 4)
SPCRmask |= ((0 << SPR1) | (0 << SPR0));
SPSRmask |= (0 << SPI2X);
} else if (LineCoding.BaudRateBPS == 14400) { // 1Mhz SPI (Fosc / 8)
SPCRmask |= ((0 << SPR1) | (1 << SPR0));
SPSRmask |= (1 << SPI2X);
} else if (LineCoding.BaudRateBPS == 57600) { // 500kHz SPI (Fosc / 16)
SPCRmask |= ((0 << SPR1) | (1 << SPR0));
SPSRmask |= (0 << SPI2X);
} else if (LineCoding.BaudRateBPS == 38400) { // 250kHz SPI (Fosc / 32)
SPCRmask |= ((1 << SPR1) | (0 << SPR0));
SPSRmask |= (1 << SPI2X);
} else if (LineCoding.BaudRateBPS == 19200) { // 125kHz SPI (Fosc / 64)
SPCRmask |= ((1 << SPR1) | (0 << SPR0));
SPSRmask |= (0 << SPI2X);
} else if (LineCoding.BaudRateBPS == 115200) { // 62.5kHz SPI (Fosc / 128)
SPCRmask |= ((1 << SPR1) | (1 << SPR0));
SPSRmask |= (0 << SPI2X);
}
SPCR = SPCRmask;
SPSR = SPSRmask;
// only read if first run
if (firstRun) {
tempIOreg = SPSR; //need to read to initiliaze
tempIOreg = SPDR; //need to read to initiliaze
firstRun = 0;
}
}
/* process data according to AVR910 protocol */
void processHostSPIRequest(void) {
uint8_t readByte1 = 0;
uint8_t readByte2 = 0;
uint8_t readByte3 = 0;
uint8_t readByte4 = 0;
uint8_t firstByte = 0;
/* Taken from a90isp_ver23.asm:
+-------------+------------+------+
;* Commands | Host writes | Host reads | |
;* -------- +-----+-------+------+-----+ |
;* | ID | data | data | | Note |
;* +-----------------------------------+-----+-------+------+-----+------+
;* | Enter programming mode | 'P' | | | 13d | 1 |
;* | Report autoincrement address | 'a' | | | 'Y' | |
;* | Set address | 'A' | ah al | | 13d | 2 |
;* | Write program memory, low byte | 'c' | dd | | 13d | 3 |
;* | Write program memory, high byte | 'C' | dd | | 13d | 3 |
;* | Issue Page Write | 'm' | | | 13d | |
;* | Read program memory | 'R' | |dd(dd)| | 4 |
;* | Write data memory | 'D' | dd | | 13d | |
;* | Read data memory | 'd' | | dd | | |
;* | Chip erase | 'e' | | | 13d | |
;* | Write lock bits | 'l' | dd | | 13d | |
;* | Write fuse bits | 'f' | dd | | 13d | 11 |
;* | Read fuse and lock bits | 'F' | | dd | | 11 |
;* | Leave programming mode | 'L' | | | 13d | 5 |
;* | Select device type | 'T' | dd | | 13d | 6 |
;* | Read signature bytes | 's' | | 3*dd | | |
;* | Return supported device codes | 't' | | n*dd | 00d | 7 |
;* | Return software identifier | 'S' | | s[7] | | 8 |
;* | Return sofware version | 'V' | |dd dd | | 9 |
;* | Return hardware version | 'v' | |dd dd | | 9 |
;* | Return programmer type | 'p' | | dd | | 10 |
;* | Set LED | 'x' | dd | | 13d | 12 |
;* | Clear LED | 'y' | dd | | 13d | 12 |
;* | Universial command | ':' | 3*dd | dd | 13d | |
;* | New universal command | '.' | 4*dd | dd | 13d | |
;* | Special test command | 'Z' | 2*dd | dd | | |
*/
firstByte = Buffer_GetElement(&Rx_Buffer);
Buffer_Initialize(&Tx_Buffer); // make sure the buffer is clear before proceeding
if (firstByte == 'P') { // enter Programming mode
// enable SPI -- already done
// enter programming mode on target:
//PORTB = 0; // set clock to zero
RESETPORT = (1 << RESETPIN); // set RESET pin on target to 1
RESETPORT2 = (1 << RESETPIN2);
delay_ms(DELAY_SHORT);
//RESETPORT = (RESETPORT & ~(1 << RESETPIN)); // set RESET pin on target to 0 - Active
RESETPORT = 0x00;
RESETPORT2 = 0;
delay_ms(DELAY_SHORT);
SPI_SendByte(0xAC);
SPI_SendByte(0x53);
SPI_SendByte(0x00);
SPI_SendByte(0x00);
delay_ms(DELAY_VERYSHORT);
Buffer_StoreElement(&Tx_Buffer, CR_HEX); // return carriage return (CR_HEX) if successful
} else if (firstByte == 'T') { // Select device type
deviceCode = Buffer_GetElement(&Rx_Buffer); // set device type
Buffer_StoreElement(&Tx_Buffer, CR_HEX); // return carriage return (CR_HEX) if successful
} else if (firstByte == 'a') { // Report autoincrement address
Buffer_StoreElement(&Tx_Buffer, 'Y'); // return 'Y' - Auto-increment enabled
} else if (firstByte == 'A') { //Load Address
// get two bytes over serial and set currAddress to them
readByte1 = Buffer_GetElement(&Rx_Buffer); // high byte
readByte2 = Buffer_GetElement(&Rx_Buffer); // low byte
currAddress = (readByte1 << 8) | (readByte2);
Buffer_StoreElement(&Tx_Buffer, CR_HEX); // return carriage return (CR_HEX) if successful
} else if (firstByte == 'c') { // Write program memory, low byte
// send 4 bytes over SPI; 0x40, then Address High Byte, then Low, then data
readByte1 = Buffer_GetElement(&Rx_Buffer);
SPI_SendByte(0x40);
SPI_SendByte((currAddress >> 8)); // high byte
SPI_SendByte((currAddress)); // low byte
SPI_SendByte(readByte1); // data
delay_ms(DELAY_MEDIUM); // certain MCUs require a delay of about 24585 cycles
Buffer_StoreElement(&Tx_Buffer, CR_HEX); // return carriage return (CR_HEX) if successful
} else if (firstByte == 'C') { // Write program memory, high byte
// send 4 bytes over SPI; 0x48, then Address High Byte, then Low, then data
readByte1 = Buffer_GetElement(&Rx_Buffer);
SPI_SendByte(0x48);
SPI_SendByte((currAddress >> 8)); // high byte
SPI_SendByte((currAddress)); // low byte
SPI_SendByte(readByte1); // data
currAddress++; // increment currAddress
Buffer_StoreElement(&Tx_Buffer, CR_HEX); // return carriage return (CR_HEX) if successful
} else if (firstByte == 'm') { // Write Program Memory Page
// send 4 bytes over SPI; 0x4c, then Address High Byte, then Low, then 0x00
SPI_SendByte(0x4C);
SPI_SendByte((currAddress >> 8)); // high byte
SPI_SendByte((currAddress)); // low byte
SPI_SendByte(0x00);
delay_ms(DELAY_LONG);
Buffer_StoreElement(&Tx_Buffer, CR_HEX); // return carriage return (CR_HEX) if successful
} else if (firstByte == 'R') { // Read Program Memory
// send 4 bytes over SPI; 0x28, then Address High Byte, then Low, then send back read data from 4th byte over serial
SPI_SendByte(0x28);
SPI_SendByte((currAddress >> 8)); // high byte
SPI_SendByte((currAddress)); // low byte
readByte1 = SPI_TransferByte(0x00); // read in data
Buffer_StoreElement(&Tx_Buffer, readByte1);
// send 4 bytes over SPI; 0x20, then Address High Byte, then Low, then send back read data from 4th byte over serial
SPI_SendByte(0x20);
SPI_SendByte((currAddress >> 8)); // high byte
SPI_SendByte((currAddress)); // low byte
readByte2 = SPI_TransferByte(0x00); // read in data
Buffer_StoreElement(&Tx_Buffer, readByte2);
currAddress++; // increment currAddress
} else if (firstByte == 'D') { // Write Data Memory
// send 4 bytes over SPI; 0xc0, then Address High Byte, then Low, then data
readByte1 = Buffer_GetElement(&Rx_Buffer);
SPI_SendByte(0xC0);
SPI_SendByte((currAddress >> 8)); // high byte
SPI_SendByte((currAddress)); // low byte
SPI_SendByte(readByte1); // data
delay_ms(DELAY_MEDIUM);
currAddress++; // increment currAddress
Buffer_StoreElement(&Tx_Buffer, CR_HEX); // return carriage return (CR_HEX) if successful
} else if (firstByte == 'd') { // Read Data Memory
// send 4 bytes over SPI; 0xa0, then Address High Byte, then Low, then send back read data from 4th byte over serial
SPI_SendByte(0xA0);
SPI_SendByte((currAddress >> 8)); // high byte
SPI_SendByte((currAddress)); // low byte
readByte1 = SPI_TransferByte(0x00); // read in data
Buffer_StoreElement(&Tx_Buffer, readByte1);
currAddress++; // increment currAddress
} else if (firstByte == 'e') { // erase the target device
// send 4 bytes over SPI; 0xac, 0x80, 0x04, 0x00
SPI_SendByte(0xAC);
SPI_SendByte(0x80);
SPI_SendByte(0x04);
SPI_SendByte(0x00);
delay_ms(DELAY_LONG);
Buffer_StoreElement(&Tx_Buffer, CR_HEX); // return carriage return (CR_HEX) if successful
} else if (firstByte == 'l') { // write lock bits
// send 4 bytes over SPI; 0xac, [andi s_data 0x06], 0xe0, 0x00
readByte1 = Buffer_GetElement(&Rx_Buffer); // read in lock bits data
SPI_SendByte(0xAC);
SPI_SendByte(((0x06 & readByte1) | 0xE0)); // TODO - is this correct???
SPI_SendByte(0x00);
SPI_SendByte(0x00);
delay_ms(DELAY_MEDIUM);
Buffer_StoreElement(&Tx_Buffer, CR_HEX); // return carriage return (CR_HEX) if successful
} else if (firstByte == 'f') { // write fuse bits
// ignore this command, but need to remove data from the receive buffer
readByte1 = Buffer_GetElement(&Rx_Buffer);
Buffer_StoreElement(&Tx_Buffer, CR_HEX); // return carriage return (CR_HEX) if successful
} else if (firstByte == 'L') { // leave programming mode
RESETPORT |= (1 << RESETPIN); // set RESET pin on target to 1
RESETPORT2 |= (1 << RESETPIN2); // set RESET pin on target to 1
Buffer_StoreElement(&Tx_Buffer, CR_HEX); // return carriage return (CR_HEX) if successful
} else if (firstByte == 's') { // Read signature bytes
// send 4 bytes over SPI; 0x30, 0x00, 0x02, read and send last byte over serial
SPI_SendByte(0x30);
SPI_SendByte(0x00);
SPI_SendByte(0x02);
readByte1 = SPI_TransferByte(0x00); // read in data
Buffer_StoreElement(&Tx_Buffer, readByte1);
SPI_SendByte(0x30);
SPI_SendByte(0x00);
SPI_SendByte(0x01);
readByte1 = SPI_TransferByte(0x00); // read in data
Buffer_StoreElement(&Tx_Buffer, readByte1);
SPI_SendByte(0x30);
SPI_SendByte(0x00);
SPI_SendByte(0x00);
readByte1 = SPI_TransferByte(0x00); // read in data
Buffer_StoreElement(&Tx_Buffer, readByte1);
} else if (firstByte == 't') { // Return supported device codes
Buffer_StoreElement(&Tx_Buffer, AVRDEVCODE01);
Buffer_StoreElement(&Tx_Buffer, AVRDEVCODE02);
Buffer_StoreElement(&Tx_Buffer, AVRDEVCODE03);
Buffer_StoreElement(&Tx_Buffer, AVRDEVCODE04);
Buffer_StoreElement(&Tx_Buffer, AVRDEVCODE05);
Buffer_StoreElement(&Tx_Buffer, AVRDEVCODE06);
Buffer_StoreElement(&Tx_Buffer, AVRDEVCODE07);
Buffer_StoreElement(&Tx_Buffer, AVRDEVCODE08);
Buffer_StoreElement(&Tx_Buffer, AVRDEVCODE09);
Buffer_StoreElement(&Tx_Buffer, AVRDEVCODE10);
Buffer_StoreElement(&Tx_Buffer, AVRDEVCODE11);
Buffer_StoreElement(&Tx_Buffer, AVRDEVCODE12);
Buffer_StoreElement(&Tx_Buffer, AVRDEVCODE13);
Buffer_StoreElement(&Tx_Buffer, AVRDEVCODE14);
Buffer_StoreElement(&Tx_Buffer, 0x00);
} else if (firstByte == 'S') { // Return software identifier
// return string[7] with "AVR ISP"
Buffer_StoreElement(&Tx_Buffer, 'A');
Buffer_StoreElement(&Tx_Buffer, 'V');
Buffer_StoreElement(&Tx_Buffer, 'R');
Buffer_StoreElement(&Tx_Buffer, 0x20);
Buffer_StoreElement(&Tx_Buffer, 'I');
Buffer_StoreElement(&Tx_Buffer, 'S');
Buffer_StoreElement(&Tx_Buffer, 'P');
} else if (firstByte == 'V') { // Return sofware version
//return two bytes, software Major then Minor
Buffer_StoreElement(&Tx_Buffer, '2');
Buffer_StoreElement(&Tx_Buffer, '3');
} else if (firstByte == 'v') { // Return hardware version
//return two bytes, hardware Major then Minor
Buffer_StoreElement(&Tx_Buffer, ('1'));
Buffer_StoreElement(&Tx_Buffer, ('0'));
} else if (firstByte == 'p') { // Return programmer type
// return 'S' for Serial Programmer
Buffer_StoreElement(&Tx_Buffer, 'S');
} else if (firstByte == 'x') { // set LED
// ignore this command, but need to remove data from the receive buffer
readByte1 = Buffer_GetElement(&Rx_Buffer);
Buffer_StoreElement(&Tx_Buffer, CR_HEX); // return carriage return (CR_HEX) if successful
} else if (firstByte == 'y') { // clear LED
// ignore this command, but need to remove data from the receive buffer
readByte1 = Buffer_GetElement(&Rx_Buffer);
Buffer_StoreElement(&Tx_Buffer, CR_HEX); // return carriage return (CR_HEX) if successful
} else if (firstByte == ':') { // Universal Command
// get 3 bytes over serial
readByte1 = Buffer_GetElement(&Rx_Buffer);
readByte2 = Buffer_GetElement(&Rx_Buffer);
readByte3 = Buffer_GetElement(&Rx_Buffer);
SPI_SendByte(readByte1);
SPI_SendByte(readByte2);
SPI_SendByte(readByte3);
readByte1 = SPI_TransferByte(0x00);
Buffer_StoreElement(&Tx_Buffer, readByte1);
delay_ms(DELAY_MEDIUM);
Buffer_StoreElement(&Tx_Buffer, CR_HEX); // return carriage return (CR_HEX) if successful
} else if (firstByte == '.') { // New Universal Command
// get 4 bytes over serial
readByte1 = Buffer_GetElement(&Rx_Buffer);
readByte2 = Buffer_GetElement(&Rx_Buffer);
readByte3 = Buffer_GetElement(&Rx_Buffer);
readByte4 = Buffer_GetElement(&Rx_Buffer);
SPI_SendByte(readByte1);
SPI_SendByte(readByte2);
SPI_SendByte(readByte3);
readByte1 = SPI_TransferByte(readByte4);
Buffer_StoreElement(&Tx_Buffer, readByte1);
delay_ms(DELAY_MEDIUM);
Buffer_StoreElement(&Tx_Buffer, CR_HEX); // return carriage return (CR_HEX) if successful
} else if (firstByte == 'Z') { // Special test command
// do nothing, but need to remove data from the receive buffer
readByte1 = Buffer_GetElement(&Rx_Buffer);
readByte2 = Buffer_GetElement(&Rx_Buffer);
} else {
// do nothing, but need to return with a carriage return
Buffer_StoreElement(&Tx_Buffer, CR_HEX); // return carriage return (CR_HEX) if successful
}
}
void delay_ms(uint8_t dly) {
uint16_t endtime = 0;
endtime = TCNT1;
if (endtime > 63486) {
endtime = (dly * DELAY_MULTIPLE);
} else {
endtime += (dly * DELAY_MULTIPLE);
}
timerval = TCNT1;
while (timerval < endtime) {
timerval = TCNT1;
}
}

@ -0,0 +1,194 @@
/*
LUFA Library
Copyright (C) Dean Camera, 2009.
dean [at] fourwalledcubicle [dot] com
www.fourwalledcubicle.com
*/
/*
Copyright 2009 Dean Camera (dean [at] fourwalledcubicle [dot] com)
Permission to use, copy, modify, and distribute this software
and its documentation for any purpose and without fee is hereby
granted, provided that the above copyright notice appear in all
copies and that both that the copyright notice and this
permission notice and warranty disclaimer appear in supporting
documentation, and that the name of the author not be used in
advertising or publicity pertaining to distribution of the
software without specific, written prior permission.
The author disclaim all warranties with regard to this
software, including all implied warranties of merchantability
and fitness. In no event shall the author be liable for any
special, indirect or consequential damages or any damages
whatsoever resulting from loss of use, data or profits, whether
in an action of contract, negligence or other tortious action,
arising out of or in connection with the use or performance of
this software.
*/
/** \file
*
* Header file for USBtoSerial.c.
*/
#ifndef _AVRISP_PROGRAMMER_H_
#define _AVRISP_PROGRAMMER_H_
/* Includes: */
#include <avr/io.h>
#include <avr/wdt.h>
#include <avr/interrupt.h>
#include "Descriptors.h"
#include "RingBuff.h"
#include <LUFA/Version.h> // Library Version Information
#include <LUFA/Common/ButtLoadTag.h> // PROGMEM tags readable by the ButtLoad project
#include <LUFA/Drivers/USB/USB.h> // USB Functionality
#include <LUFA/Drivers/AT90USBXXX/SPI.h> // SPI driver
#include <LUFA/Drivers/Board/LEDs.h> // LEDs driver
#include <LUFA/Scheduler/Scheduler.h> // Simple scheduler for task management
/* Macros: */
/** CDC Class specific request to get the current virtual serial port configuration settings. */
#define REQ_GetLineEncoding 0x21
/** CDC Class specific request to set the current virtual serial port configuration settings. */
#define REQ_SetLineEncoding 0x20
/** CDC Class specific request to set the current virtual serial port handshake line states. */
#define REQ_SetControlLineState 0x22
/** Notification type constant for a change in the virtual serial port handshake line states, for
* use with a USB_Notification_Header_t notification structure when sent to the host via the CDC
* notification endpoint.
*/
#define NOTIF_SerialState 0x20
/** Mask for the DTR handshake line for use with the REQ_SetControlLineState class specific request
* from the host, to indicate that the DTR line state should be high.
*/
#define CONTROL_LINE_OUT_DTR (1 << 0)
/** Mask for the RTS handshake line for use with the REQ_SetControlLineState class specific request
* from the host, to indicate that theRTS line state should be high.
*/
#define CONTROL_LINE_OUT_RTS (1 << 1)
/** Mask for the DCD handshake line for use with the a NOTIF_SerialState class specific notification
* from the device to the host, to indicate that the DCD line state is currently high.
*/
#define CONTROL_LINE_IN_DCD (1 << 0)
/** Mask for the DSR handshake line for use with the a NOTIF_SerialState class specific notification
* from the device to the host, to indicate that the DSR line state is currently high.
*/
#define CONTROL_LINE_IN_DSR (1 << 1)
/** Mask for the BREAK handshake line for use with the a NOTIF_SerialState class specific notification
* from the device to the host, to indicate that the BREAK line state is currently high.
*/
#define CONTROL_LINE_IN_BREAK (1 << 2)
/** Mask for the RING handshake line for use with the a NOTIF_SerialState class specific notification
* from the device to the host, to indicate that the RING line state is currently high.
*/
#define CONTROL_LINE_IN_RING (1 << 3)
/** Mask for use with the a NOTIF_SerialState class specific notification from the device to the host,
* to indicate that a framing error has ocurred on the virtual serial port.
*/
#define CONTROL_LINE_IN_FRAMEERROR (1 << 4)
/** Mask for use with the a NOTIF_SerialState class specific notification from the device to the host,
* to indicate that a parity error has ocurred on the virtual serial port.
*/
#define CONTROL_LINE_IN_PARITYERROR (1 << 5)
/** Mask for use with the a NOTIF_SerialState class specific notification from the device to the host,
* to indicate that a data overrun error has ocurred on the virtual serial port.
*/
#define CONTROL_LINE_IN_OVERRUNERROR (1 << 6)
/* Event Handlers: */
/** Indicates that this module will catch the USB_Connect event when thrown by the library. */
HANDLES_EVENT(USB_Connect);
/** Indicates that this module will catch the USB_Disconnect event when thrown by the library. */
HANDLES_EVENT(USB_Disconnect);
/** Indicates that this module will catch the USB_ConfigurationChanged event when thrown by the library. */
HANDLES_EVENT(USB_ConfigurationChanged);
/** Indicates that this module will catch the USB_UnhandledControlPacket event when thrown by the library. */
HANDLES_EVENT(USB_UnhandledControlPacket);
/* Type Defines: */
/** Type define for the virtual serial port line encoding settings, for storing the current USART configuration
* as set by the host via a class specific request.
*/
typedef struct
{
uint32_t BaudRateBPS; /**< Baud rate of the virtual serial port, in bits per second */
uint8_t CharFormat; /**< Character format of the virtual serial port, a value from the
* CDCDevice_CDC_LineCodingFormats_t enum
*/
uint8_t ParityType; /**< Parity setting of the virtual serial port, a value from the
* CDCDevice_LineCodingParity_t enum
*/
uint8_t DataBits; /**< Bits of data per charater of the virtual serial port */
} CDC_Line_Coding_t;
/** Type define for a CDC notification, sent to the host via the CDC notification endpoint to indicate a
* change in the device state asynchronously.
*/
typedef struct
{
uint8_t NotificationType; /**< Notification type, a mask of REQDIR_*, REQTYPE_* and REQREC_* constants
* from the library StdRequestType.h header
*/
uint8_t Notification; /**< Notification value, a NOTIF_* constant */
uint16_t wValue; /**< Notification wValue, notification-specific */
uint16_t wIndex; /**< Notification wIndex, notification-specific */
uint16_t wLength; /**< Notification wLength, notification-specific */
} USB_Notification_Header_t;
/* Enums: */
/** Enum for the possible line encoding formats of a virtual serial port. */
enum CDCDevice_CDC_LineCodingFormats_t
{
OneStopBit = 0, /**< Each frame contains one stop bit */
OneAndAHalfStopBits = 1, /**< Each frame contains one and a half stop bits */
TwoStopBits = 2, /**< Each frame contains two stop bits */
};
/** Enum for the possible line encoding parity settings of a virtual serial port. */
enum CDCDevice_LineCodingParity_t
{
Parity_None = 0, /**< No parity bit mode on each frame */
Parity_Odd = 1, /**< Odd parity bit mode on each frame */
Parity_Even = 2, /**< Even parity bit mode on each frame */
Parity_Mark = 3, /**< Mark parity bit mode on each frame */
Parity_Space = 4, /**< Space parity bit mode on each frame */
};
/** Enum for the possible status codes for passing to the UpdateStatus() function. */
enum USBtoSerial_StatusCodes_t
{
Status_USBNotReady = 0, /**< USB is not ready (disconnected from a USB host) */
Status_USBEnumerating = 1, /**< USB interface is enumerating */
Status_USBReady = 2, /**< USB interface is connected and ready */
};
/* Tasks: */
TASK(CDC_Task);
/* Function Prototypes: */
void ReconfigureSPI(void);
void UpdateStatus(uint8_t CurrentStatus);
void processHostSPIRequest(void);
void delay_ms(uint8_t dly);
#endif

@ -0,0 +1,89 @@
/** \file
*
* This file contains special DoxyGen information for the generation of the main page and other special
* documentation pages. It is not a project source file.
*/
/** \mainpage AVRISP_Programmer
*
* Communications Device Class demonstration application.
* This gives a simple reference application for implementing
* a USB to Serial converter using the CDC class. Data communicated
* over the USB Virtual Serial Port according to Atmel's AVR910
* protocol is used to program AVR MCUs that are
* "In-System Programmable via SPI Port".
*
* After running this firmware for the first time on a new computer,
* you will need to supply the .INF file located in this demo
* project's directory as the device's driver when running under
* Windows. This will enable Windows to use its inbuilt CDC drivers,
* negating the need for custom drivers for the device. Other
* Operating Systems should automatically use their own inbuilt
* CDC-ACM drivers.
*
* Usage:
* avrdude -vv -F -P COM7 -c avr910 -p t261
* Note -F flag which overrides signature check and enables programming
* of any "In-System Programmable via SPI Port" AVR MCU. Part number,
* t261, should be set to your target device.
* avrdude -vv -F -P COM7 -c avr910 -p t261 -U flash:w:PROG.hex
* PROG.hex is the hex file to program your t261 AVR with
* avrdude -vv -F -P COM7 -b 115200 -c avr910 -p t261 -U flash:w:test.hex
* The -b 115200 sets the SPI clock to 62.5kHz from the default 125kHz and may
* work when the default programming speed fails.
* AVROSP.exe -dATtiny261 -cCOM7 -rf
* AVRosp is the Open Source AVR ISP Programming Software available from Atmel.com
*
* Note: on Linux systems, COM7 should be replaced with someting like /dev/ttyACM0
* You can determine this value by running dmesg after plugging in the device
* Note: you must RESET the programmer after each use (AVRdude session).
*
* Note: If you experience errors with older devices, try changing DELAY_LONG
* to a larger value, such as 0xFF in AVRISP_Programmer.c
*
* MISO, MOSI, and SCK are connected directly from the AVRopendous board
* to the pin of the same functionality on the target. RESET pin on the target
* can be connected either to SS (PB0), or PC2. Do not have any other pins
* connected - especially HWB pin, to avoid unintentional behaviour.
*
* AVR910 functionality was overlayed on USBtoSerial functionality.
* Keep this in mind when looking over the code.
* Default target speed is 125kHz and corresponds to 19200 baud, which
* is the default setting for AVRdude.
*
* Changing "Baud-Rate" will change the SPI speed. Defualt SPI clock speed
* is 8Mhz / 4 = 2MHz. 8Mhz is the device clock speed. This is the setting at
* 9600 baud. The following is a table of baud-rate vs. SPI Speed that will result
* 9600 = 2Mhz
* 14400 = 1MHz
* 19200 = 125kHz (AVRdude Default)
* 38400 = 250kHz
* 57600 = 500kHz
* 115200 = 62.5kHz
*
*
*
*
* <table>
* <tr>
* <td><b>USB Mode:</b></td>
* <td>Device</td>
* </tr>
* <tr>
* <td><b>USB Class:</b></td>
* <td>Communications Device Class (CDC)</td>
* </tr>
* <tr>
* <td><b>USB Subclass:</b></td>
* <td>Abstract Control Model (ACM)</td>
* </tr>
* <tr>
* <td><b>Relevant Standards:</b></td>
* <td>USBIF CDC Class Standard</td>
* </tr>
* <tr>
* <td><b>Usable Speeds:</b></td>
* <td>Full Speed Mode</td>
* </tr>
* </table>
*/

Binary file not shown.

After

Width:  |  Height:  |  Size: 73 KiB

@ -0,0 +1,263 @@
/*
LUFA Library
Copyright (C) Dean Camera, 2009.
dean [at] fourwalledcubicle [dot] com
www.fourwalledcubicle.com
*/
/*
Copyright 2009 Dean Camera (dean [at] fourwalledcubicle [dot] com)
Permission to use, copy, modify, and distribute this software
and its documentation for any purpose and without fee is hereby
granted, provided that the above copyright notice appear in all
copies and that both that the copyright notice and this
permission notice and warranty disclaimer appear in supporting
documentation, and that the name of the author not be used in
advertising or publicity pertaining to distribution of the
software without specific, written prior permission.
The author disclaim all warranties with regard to this
software, including all implied warranties of merchantability
and fitness. In no event shall the author be liable for any
special, indirect or consequential damages or any damages
whatsoever resulting from loss of use, data or profits, whether
in an action of contract, negligence or other tortious action,
arising out of or in connection with the use or performance of
this software.
*/
/** \file
*
* USB Device Descriptors, for library use when in USB device mode. Descriptors are special
* computer-readable structures which the host requests upon device enumeration, to determine
* the device's capabilities and functions.
*/
#include "Descriptors.h"
/** Device descriptor structure. This descriptor, located in FLASH memory, describes the overall
* device characteristics, including the supported USB version, control endpoint size and the
* number of device configurations. The descriptor is read out by the USB host when the enumeration
* process begins.
*/
USB_Descriptor_Device_t PROGMEM DeviceDescriptor =
{
Header: {Size: sizeof(USB_Descriptor_Device_t), Type: DTYPE_Device},
USBSpecification: VERSION_BCD(01.10),
Class: 0x02,
SubClass: 0x00,
Protocol: 0x00,
Endpoint0Size: 8,
VendorID: 0x03EB,
ProductID: 0x204F,
ReleaseNumber: 0x0000,
ManufacturerStrIndex: 0x01,
ProductStrIndex: 0x02,
SerialNumStrIndex: NO_DESCRIPTOR,
NumberOfConfigurations: 1
};
/** Configuration descriptor structure. This descriptor, located in FLASH memory, describes the usage
* of the device in one of its supported configurations, including information about any device interfaces
* and endpoints. The descriptor is read out by the USB host during the enumeration process when selecting
* a configuration so that the host may correctly communicate with the USB device.
*/
USB_Descriptor_Configuration_t PROGMEM ConfigurationDescriptor =
{
Config:
{
Header: {Size: sizeof(USB_Descriptor_Configuration_Header_t), Type: DTYPE_Configuration},
TotalConfigurationSize: sizeof(USB_Descriptor_Configuration_t),
TotalInterfaces: 2,
ConfigurationNumber: 1,
ConfigurationStrIndex: NO_DESCRIPTOR,
ConfigAttributes: (USB_CONFIG_ATTR_BUSPOWERED | USB_CONFIG_ATTR_SELFPOWERED),
MaxPowerConsumption: USB_CONFIG_POWER_MA(100)
},
CCI_Interface:
{
Header: {Size: sizeof(USB_Descriptor_Interface_t), Type: DTYPE_Interface},
InterfaceNumber: 0,
AlternateSetting: 0,
TotalEndpoints: 1,
Class: 0x02,
SubClass: 0x02,
Protocol: 0x01,
InterfaceStrIndex: NO_DESCRIPTOR
},
CDC_Functional_IntHeader:
{
Header: {Size: sizeof(CDC_FUNCTIONAL_DESCRIPTOR(2)), Type: 0x24},
SubType: 0x00,
Data: {0x01, 0x10}
},
CDC_Functional_CallManagement:
{
Header: {Size: sizeof(CDC_FUNCTIONAL_DESCRIPTOR(2)), Type: 0x24},
SubType: 0x01,
Data: {0x03, 0x01}
},
CDC_Functional_AbstractControlManagement:
{
Header: {Size: sizeof(CDC_FUNCTIONAL_DESCRIPTOR(1)), Type: 0x24},
SubType: 0x02,
Data: {0x06}
},
CDC_Functional_Union:
{
Header: {Size: sizeof(CDC_FUNCTIONAL_DESCRIPTOR(2)), Type: 0x24},
SubType: 0x06,
Data: {0x00, 0x01}
},
ManagementEndpoint:
{
Header: {Size: sizeof(USB_Descriptor_Endpoint_t), Type: DTYPE_Endpoint},
EndpointAddress: (ENDPOINT_DESCRIPTOR_DIR_IN | CDC_NOTIFICATION_EPNUM),
Attributes: EP_TYPE_INTERRUPT,
EndpointSize: CDC_NOTIFICATION_EPSIZE,
PollingIntervalMS: 0xFF
},
DCI_Interface:
{
Header: {Size: sizeof(USB_Descriptor_Interface_t), Type: DTYPE_Interface},
InterfaceNumber: 1,
AlternateSetting: 0,
TotalEndpoints: 2,
Class: 0x0A,
SubClass: 0x00,
Protocol: 0x00,
InterfaceStrIndex: NO_DESCRIPTOR
},
DataOutEndpoint:
{
Header: {Size: sizeof(USB_Descriptor_Endpoint_t), Type: DTYPE_Endpoint},
EndpointAddress: (ENDPOINT_DESCRIPTOR_DIR_OUT | CDC_RX_EPNUM),
Attributes: EP_TYPE_BULK,
EndpointSize: CDC_TXRX_EPSIZE,
PollingIntervalMS: 0x00
},
DataInEndpoint:
{
Header: {Size: sizeof(USB_Descriptor_Endpoint_t), Type: DTYPE_Endpoint},
EndpointAddress: (ENDPOINT_DESCRIPTOR_DIR_IN | CDC_TX_EPNUM),
Attributes: EP_TYPE_BULK,
EndpointSize: CDC_TXRX_EPSIZE,
PollingIntervalMS: 0x00
}
};
/** Language descriptor structure. This descriptor, located in FLASH memory, is returned when the host requests
* the string descriptor with index 0 (the first index). It is actually an array of 16-bit integers, which indicate
* via the language ID table available at USB.org what languages the device supports for its string descriptors.
*/
USB_Descriptor_String_t PROGMEM LanguageString =
{
Header: {Size: USB_STRING_LEN(1), Type: DTYPE_String},
UnicodeString: {LANGUAGE_ID_ENG}
};
/** Manufacturer descriptor string. This is a Unicode string containing the manufacturer's details in human readable
* form, and is read out upon request by the host when the appropriate string ID is requested, listed in the Device
* Descriptor.
*/
USB_Descriptor_String_t PROGMEM ManufacturerString =
{
Header: {Size: USB_STRING_LEN(19), Type: DTYPE_String},
UnicodeString: L"www.AVRopendous.org"
};
/** Product descriptor string. This is a Unicode string containing the product's details in human readable form,
* and is read out upon request by the host when the appropriate string ID is requested, listed in the Device
* Descriptor.
*/
USB_Descriptor_String_t PROGMEM ProductString =
{
Header: {Size: USB_STRING_LEN(29), Type: DTYPE_String},
UnicodeString: L"LUFA-Based AVR ISP Programmer"
};
/** This function is called by the library when in device mode, and must be overridden (see StdDescriptors.h
* documentation) by the application code so that the address and size of a requested descriptor can be given
* to the USB library. When the device recieves a Get Descriptor request on the control endpoint, this function
* is called so that the descriptor details can be passed back and the appropriate descriptor sent back to the
* USB host.
*/
uint16_t USB_GetDescriptor(const uint16_t wValue, const uint8_t wIndex, void** const DescriptorAddress)
{
const uint8_t DescriptorType = (wValue >> 8);
const uint8_t DescriptorNumber = (wValue & 0xFF);
void* Address = NULL;
uint16_t Size = NO_DESCRIPTOR;
switch (DescriptorType)
{
case DTYPE_Device:
Address = DESCRIPTOR_ADDRESS(DeviceDescriptor);
Size = sizeof(USB_Descriptor_Device_t);
break;
case DTYPE_Configuration:
Address = DESCRIPTOR_ADDRESS(ConfigurationDescriptor);
Size = sizeof(USB_Descriptor_Configuration_t);
break;
case DTYPE_String:
switch (DescriptorNumber)
{
case 0x00:
Address = DESCRIPTOR_ADDRESS(LanguageString);
Size = pgm_read_byte(&LanguageString.Header.Size);
break;
case 0x01:
Address = DESCRIPTOR_ADDRESS(ManufacturerString);
Size = pgm_read_byte(&ManufacturerString.Header.Size);
break;
case 0x02:
Address = DESCRIPTOR_ADDRESS(ProductString);
Size = pgm_read_byte(&ProductString.Header.Size);
break;
}
break;
}
*DescriptorAddress = Address;
return Size;
}

@ -0,0 +1,98 @@
/*
LUFA Library
Copyright (C) Dean Camera, 2009.
dean [at] fourwalledcubicle [dot] com
www.fourwalledcubicle.com
*/
/*
Copyright 2009 Dean Camera (dean [at] fourwalledcubicle [dot] com)
Permission to use, copy, modify, and distribute this software
and its documentation for any purpose and without fee is hereby
granted, provided that the above copyright notice appear in all
copies and that both that the copyright notice and this
permission notice and warranty disclaimer appear in supporting
documentation, and that the name of the author not be used in
advertising or publicity pertaining to distribution of the
software without specific, written prior permission.
The author disclaim all warranties with regard to this
software, including all implied warranties of merchantability
and fitness. In no event shall the author be liable for any
special, indirect or consequential damages or any damages
whatsoever resulting from loss of use, data or profits, whether
in an action of contract, negligence or other tortious action,
arising out of or in connection with the use or performance of
this software.
*/
/** \file
*
* Header file for Descriptors.c.
*/
#ifndef _DESCRIPTORS_H_
#define _DESCRIPTORS_H_
/* Includes: */
#include <LUFA/Drivers/USB/USB.h>
#include <avr/pgmspace.h>
/* Macros: */
/** Macro to define a CDC class-specific functional descriptor. CDC functional descriptors have a
* uniform structure but variable sized data payloads, thus cannot be represented accurately by
* a single typedef struct. A macro is used instead so that functional descriptors can be created
* easily by specifying the size of the payload. This allows sizeof() to work correctly.
*
* \param DataSize Size in bytes of the CDC functional descriptor's data payload
*/
#define CDC_FUNCTIONAL_DESCRIPTOR(DataSize) \
struct \
{ \
USB_Descriptor_Header_t Header; \
uint8_t SubType; \
uint8_t Data[DataSize]; \
}
/** Endpoint number of the CDC device-to-host notification IN endpoint. */
#define CDC_NOTIFICATION_EPNUM 2
/** Endpoint number of the CDC device-to-host data IN endpoint. */
#define CDC_TX_EPNUM 3
/** Endpoint number of the CDC host-to-device data OUT endpoint. */
#define CDC_RX_EPNUM 4
/** Size in bytes of the CDC device-to-host notification IN endpoint. */
#define CDC_NOTIFICATION_EPSIZE 8
/** Size in bytes of the CDC data IN and OUT endpoints. */
#define CDC_TXRX_EPSIZE 16
/* Type Defines: */
/** Type define for the device configuration descriptor structure. This must be defined in the
* application code, as the configuration descriptor contains several sub-descriptors which
* vary between devices, and which describe the device's usage to the host.
*/
typedef struct
{
USB_Descriptor_Configuration_Header_t Config;
USB_Descriptor_Interface_t CCI_Interface;
CDC_FUNCTIONAL_DESCRIPTOR(2) CDC_Functional_IntHeader;
CDC_FUNCTIONAL_DESCRIPTOR(2) CDC_Functional_CallManagement;
CDC_FUNCTIONAL_DESCRIPTOR(1) CDC_Functional_AbstractControlManagement;
CDC_FUNCTIONAL_DESCRIPTOR(2) CDC_Functional_Union;
USB_Descriptor_Endpoint_t ManagementEndpoint;
USB_Descriptor_Interface_t DCI_Interface;
USB_Descriptor_Endpoint_t DataOutEndpoint;
USB_Descriptor_Endpoint_t DataInEndpoint;
} USB_Descriptor_Configuration_t;
/* Function Prototypes: */
uint16_t USB_GetDescriptor(const uint16_t wValue, const uint8_t wIndex, void** const DescriptorAddress)
ATTR_WARN_UNUSED_RESULT ATTR_NON_NULL_PTR_ARG(3);
#endif

@ -0,0 +1,1485 @@
# Doxyfile 1.5.7.1
# This file describes the settings to be used by the documentation system
# doxygen (www.doxygen.org) for a project
#
# All text after a hash (#) is considered a comment and will be ignored
# The format is:
# TAG = value [value, ...]
# For lists items can also be appended using:
# TAG += value [value, ...]
# Values that contain spaces should be placed between quotes (" ")
#---------------------------------------------------------------------------
# Project related configuration options
#---------------------------------------------------------------------------
# This tag specifies the encoding used for all characters in the config file
# that follow. The default is UTF-8 which is also the encoding used for all
# text before the first occurrence of this tag. Doxygen uses libiconv (or the
# iconv built into libc) for the transcoding. See
# http://www.gnu.org/software/libiconv for the list of possible encodings.
DOXYFILE_ENCODING = UTF-8
# The PROJECT_NAME tag is a single word (or a sequence of words surrounded
# by quotes) that should identify the project.
PROJECT_NAME = "LUFA Library - USB to Serial Device Demo"
# The PROJECT_NUMBER tag can be used to enter a project or revision number.
# This could be handy for archiving the generated documentation or
# if some version control system is used.
PROJECT_NUMBER = 0.0.0
# The OUTPUT_DIRECTORY tag is used to specify the (relative or absolute)
# base path where the generated documentation will be put.
# If a relative path is entered, it will be relative to the location
# where doxygen was started. If left blank the current directory will be used.
OUTPUT_DIRECTORY = ./Documentation/
# If the CREATE_SUBDIRS tag is set to YES, then doxygen will create
# 4096 sub-directories (in 2 levels) under the output directory of each output
# format and will distribute the generated files over these directories.
# Enabling this option can be useful when feeding doxygen a huge amount of
# source files, where putting all generated files in the same directory would
# otherwise cause performance problems for the file system.
CREATE_SUBDIRS = YES
# The OUTPUT_LANGUAGE tag is used to specify the language in which all
# documentation generated by doxygen is written. Doxygen will use this
# information to generate all constant output in the proper language.
# The default language is English, other supported languages are:
# Afrikaans, Arabic, Brazilian, Catalan, Chinese, Chinese-Traditional,
# Croatian, Czech, Danish, Dutch, Farsi, Finnish, French, German, Greek,
# Hungarian, Italian, Japanese, Japanese-en (Japanese with English messages),
# Korean, Korean-en, Lithuanian, Norwegian, Macedonian, Persian, Polish,
# Portuguese, Romanian, Russian, Serbian, Serbian-Cyrilic, Slovak, Slovene,
# Spanish, Swedish, and Ukrainian.
OUTPUT_LANGUAGE = English
# If the BRIEF_MEMBER_DESC tag is set to YES (the default) Doxygen will
# include brief member descriptions after the members that are listed in
# the file and class documentation (similar to JavaDoc).
# Set to NO to disable this.
BRIEF_MEMBER_DESC = YES
# If the REPEAT_BRIEF tag is set to YES (the default) Doxygen will prepend
# the brief description of a member or function before the detailed description.
# Note: if both HIDE_UNDOC_MEMBERS and BRIEF_MEMBER_DESC are set to NO, the
# brief descriptions will be completely suppressed.
REPEAT_BRIEF = YES
# This tag implements a quasi-intelligent brief description abbreviator
# that is used to form the text in various listings. Each string
# in this list, if found as the leading text of the brief description, will be
# stripped from the text and the result after processing the whole list, is
# used as the annotated text. Otherwise, the brief description is used as-is.
# If left blank, the following values are used ("$name" is automatically
# replaced with the name of the entity): "The $name class" "The $name widget"
# "The $name file" "is" "provides" "specifies" "contains"
# "represents" "a" "an" "the"
ABBREVIATE_BRIEF = "The $name class" \
"The $name widget" \
"The $name file" \
is \
provides \
specifies \
contains \
represents \
a \
an \
the
# If the ALWAYS_DETAILED_SEC and REPEAT_BRIEF tags are both set to YES then
# Doxygen will generate a detailed section even if there is only a brief
# description.
ALWAYS_DETAILED_SEC = NO
# If the INLINE_INHERITED_MEMB tag is set to YES, doxygen will show all
# inherited members of a class in the documentation of that class as if those
# members were ordinary class members. Constructors, destructors and assignment
# operators of the base classes will not be shown.
INLINE_INHERITED_MEMB = NO
# If the FULL_PATH_NAMES tag is set to YES then Doxygen will prepend the full
# path before files name in the file list and in the header files. If set
# to NO the shortest path that makes the file name unique will be used.
FULL_PATH_NAMES = YES
# If the FULL_PATH_NAMES tag is set to YES then the STRIP_FROM_PATH tag
# can be used to strip a user-defined part of the path. Stripping is
# only done if one of the specified strings matches the left-hand part of
# the path. The tag can be used to show relative paths in the file list.
# If left blank the directory from which doxygen is run is used as the
# path to strip.
STRIP_FROM_PATH =
# The STRIP_FROM_INC_PATH tag can be used to strip a user-defined part of
# the path mentioned in the documentation of a class, which tells
# the reader which header file to include in order to use a class.
# If left blank only the name of the header file containing the class
# definition is used. Otherwise one should specify the include paths that
# are normally passed to the compiler using the -I flag.
STRIP_FROM_INC_PATH =
# If the SHORT_NAMES tag is set to YES, doxygen will generate much shorter
# (but less readable) file names. This can be useful is your file systems
# doesn't support long names like on DOS, Mac, or CD-ROM.
SHORT_NAMES = YES
# If the JAVADOC_AUTOBRIEF tag is set to YES then Doxygen
# will interpret the first line (until the first dot) of a JavaDoc-style
# comment as the brief description. If set to NO, the JavaDoc
# comments will behave just like regular Qt-style comments
# (thus requiring an explicit @brief command for a brief description.)
JAVADOC_AUTOBRIEF = NO
# If the QT_AUTOBRIEF tag is set to YES then Doxygen will
# interpret the first line (until the first dot) of a Qt-style
# comment as the brief description. If set to NO, the comments
# will behave just like regular Qt-style comments (thus requiring
# an explicit \brief command for a brief description.)
QT_AUTOBRIEF = NO
# The MULTILINE_CPP_IS_BRIEF tag can be set to YES to make Doxygen
# treat a multi-line C++ special comment block (i.e. a block of //! or ///
# comments) as a brief description. This used to be the default behaviour.
# The new default is to treat a multi-line C++ comment block as a detailed
# description. Set this tag to YES if you prefer the old behaviour instead.
MULTILINE_CPP_IS_BRIEF = NO
# If the INHERIT_DOCS tag is set to YES (the default) then an undocumented
# member inherits the documentation from any documented member that it
# re-implements.
INHERIT_DOCS = YES
# If the SEPARATE_MEMBER_PAGES tag is set to YES, then doxygen will produce
# a new page for each member. If set to NO, the documentation of a member will
# be part of the file/class/namespace that contains it.
SEPARATE_MEMBER_PAGES = NO
# The TAB_SIZE tag can be used to set the number of spaces in a tab.
# Doxygen uses this value to replace tabs by spaces in code fragments.
TAB_SIZE = 4
# This tag can be used to specify a number of aliases that acts
# as commands in the documentation. An alias has the form "name=value".
# For example adding "sideeffect=\par Side Effects:\n" will allow you to
# put the command \sideeffect (or @sideeffect) in the documentation, which
# will result in a user-defined paragraph with heading "Side Effects:".
# You can put \n's in the value part of an alias to insert newlines.
ALIASES =
# Set the OPTIMIZE_OUTPUT_FOR_C tag to YES if your project consists of C
# sources only. Doxygen will then generate output that is more tailored for C.
# For instance, some of the names that are used will be different. The list
# of all members will be omitted, etc.
OPTIMIZE_OUTPUT_FOR_C = YES
# Set the OPTIMIZE_OUTPUT_JAVA tag to YES if your project consists of Java
# sources only. Doxygen will then generate output that is more tailored for
# Java. For instance, namespaces will be presented as packages, qualified
# scopes will look different, etc.
OPTIMIZE_OUTPUT_JAVA = NO
# Set the OPTIMIZE_FOR_FORTRAN tag to YES if your project consists of Fortran
# sources only. Doxygen will then generate output that is more tailored for
# Fortran.
OPTIMIZE_FOR_FORTRAN = NO
# Set the OPTIMIZE_OUTPUT_VHDL tag to YES if your project consists of VHDL
# sources. Doxygen will then generate output that is tailored for
# VHDL.
OPTIMIZE_OUTPUT_VHDL = NO
# If you use STL classes (i.e. std::string, std::vector, etc.) but do not want
# to include (a tag file for) the STL sources as input, then you should
# set this tag to YES in order to let doxygen match functions declarations and
# definitions whose arguments contain STL classes (e.g. func(std::string); v.s.
# func(std::string) {}). This also make the inheritance and collaboration
# diagrams that involve STL classes more complete and accurate.
BUILTIN_STL_SUPPORT = NO
# If you use Microsoft's C++/CLI language, you should set this option to YES to
# enable parsing support.
CPP_CLI_SUPPORT = NO
# Set the SIP_SUPPORT tag to YES if your project consists of sip sources only.
# Doxygen will parse them like normal C++ but will assume all classes use public
# instead of private inheritance when no explicit protection keyword is present.
SIP_SUPPORT = NO
# For Microsoft's IDL there are propget and propput attributes to indicate getter
# and setter methods for a property. Setting this option to YES (the default)
# will make doxygen to replace the get and set methods by a property in the
# documentation. This will only work if the methods are indeed getting or
# setting a simple type. If this is not the case, or you want to show the
# methods anyway, you should set this option to NO.
IDL_PROPERTY_SUPPORT = YES
# If member grouping is used in the documentation and the DISTRIBUTE_GROUP_DOC
# tag is set to YES, then doxygen will reuse the documentation of the first
# member in the group (if any) for the other members of the group. By default
# all members of a group must be documented explicitly.
DISTRIBUTE_GROUP_DOC = NO
# Set the SUBGROUPING tag to YES (the default) to allow class member groups of
# the same type (for instance a group of public functions) to be put as a
# subgroup of that type (e.g. under the Public Functions section). Set it to
# NO to prevent subgrouping. Alternatively, this can be done per class using
# the \nosubgrouping command.
SUBGROUPING = YES
# When TYPEDEF_HIDES_STRUCT is enabled, a typedef of a struct, union, or enum
# is documented as struct, union, or enum with the name of the typedef. So
# typedef struct TypeS {} TypeT, will appear in the documentation as a struct
# with name TypeT. When disabled the typedef will appear as a member of a file,
# namespace, or class. And the struct will be named TypeS. This can typically
# be useful for C code in case the coding convention dictates that all compound
# types are typedef'ed and only the typedef is referenced, never the tag name.
TYPEDEF_HIDES_STRUCT = NO
# The SYMBOL_CACHE_SIZE determines the size of the internal cache use to
# determine which symbols to keep in memory and which to flush to disk.
# When the cache is full, less often used symbols will be written to disk.
# For small to medium size projects (<1000 input files) the default value is
# probably good enough. For larger projects a too small cache size can cause
# doxygen to be busy swapping symbols to and from disk most of the time
# causing a significant performance penality.
# If the system has enough physical memory increasing the cache will improve the
# performance by keeping more symbols in memory. Note that the value works on
# a logarithmic scale so increasing the size by one will rougly double the
# memory usage. The cache size is given by this formula:
# 2^(16+SYMBOL_CACHE_SIZE). The valid range is 0..9, the default is 0,
# corresponding to a cache size of 2^16 = 65536 symbols
SYMBOL_CACHE_SIZE = 0
#---------------------------------------------------------------------------
# Build related configuration options
#---------------------------------------------------------------------------
# If the EXTRACT_ALL tag is set to YES doxygen will assume all entities in
# documentation are documented, even if no documentation was available.
# Private class members and static file members will be hidden unless
# the EXTRACT_PRIVATE and EXTRACT_STATIC tags are set to YES
EXTRACT_ALL = YES
# If the EXTRACT_PRIVATE tag is set to YES all private members of a class
# will be included in the documentation.
EXTRACT_PRIVATE = YES
# If the EXTRACT_STATIC tag is set to YES all static members of a file
# will be included in the documentation.
EXTRACT_STATIC = YES
# If the EXTRACT_LOCAL_CLASSES tag is set to YES classes (and structs)
# defined locally in source files will be included in the documentation.
# If set to NO only classes defined in header files are included.
EXTRACT_LOCAL_CLASSES = YES
# This flag is only useful for Objective-C code. When set to YES local
# methods, which are defined in the implementation section but not in
# the interface are included in the documentation.
# If set to NO (the default) only methods in the interface are included.
EXTRACT_LOCAL_METHODS = NO
# If this flag is set to YES, the members of anonymous namespaces will be
# extracted and appear in the documentation as a namespace called
# 'anonymous_namespace{file}', where file will be replaced with the base
# name of the file that contains the anonymous namespace. By default
# anonymous namespace are hidden.
EXTRACT_ANON_NSPACES = NO
# If the HIDE_UNDOC_MEMBERS tag is set to YES, Doxygen will hide all
# undocumented members of documented classes, files or namespaces.
# If set to NO (the default) these members will be included in the
# various overviews, but no documentation section is generated.
# This option has no effect if EXTRACT_ALL is enabled.
HIDE_UNDOC_MEMBERS = NO
# If the HIDE_UNDOC_CLASSES tag is set to YES, Doxygen will hide all
# undocumented classes that are normally visible in the class hierarchy.
# If set to NO (the default) these classes will be included in the various
# overviews. This option has no effect if EXTRACT_ALL is enabled.
HIDE_UNDOC_CLASSES = NO
# If the HIDE_FRIEND_COMPOUNDS tag is set to YES, Doxygen will hide all
# friend (class|struct|union) declarations.
# If set to NO (the default) these declarations will be included in the
# documentation.
HIDE_FRIEND_COMPOUNDS = NO
# If the HIDE_IN_BODY_DOCS tag is set to YES, Doxygen will hide any
# documentation blocks found inside the body of a function.
# If set to NO (the default) these blocks will be appended to the
# function's detailed documentation block.
HIDE_IN_BODY_DOCS = NO
# The INTERNAL_DOCS tag determines if documentation
# that is typed after a \internal command is included. If the tag is set
# to NO (the default) then the documentation will be excluded.
# Set it to YES to include the internal documentation.
INTERNAL_DOCS = NO
# If the CASE_SENSE_NAMES tag is set to NO then Doxygen will only generate
# file names in lower-case letters. If set to YES upper-case letters are also
# allowed. This is useful if you have classes or files whose names only differ
# in case and if your file system supports case sensitive file names. Windows
# and Mac users are advised to set this option to NO.
CASE_SENSE_NAMES = NO
# If the HIDE_SCOPE_NAMES tag is set to NO (the default) then Doxygen
# will show members with their full class and namespace scopes in the
# documentation. If set to YES the scope will be hidden.
HIDE_SCOPE_NAMES = NO
# If the SHOW_INCLUDE_FILES tag is set to YES (the default) then Doxygen
# will put a list of the files that are included by a file in the documentation
# of that file.
SHOW_INCLUDE_FILES = YES
# If the INLINE_INFO tag is set to YES (the default) then a tag [inline]
# is inserted in the documentation for inline members.
INLINE_INFO = YES
# If the SORT_MEMBER_DOCS tag is set to YES (the default) then doxygen
# will sort the (detailed) documentation of file and class members
# alphabetically by member name. If set to NO the members will appear in
# declaration order.
SORT_MEMBER_DOCS = YES
# If the SORT_BRIEF_DOCS tag is set to YES then doxygen will sort the
# brief documentation of file, namespace and class members alphabetically
# by member name. If set to NO (the default) the members will appear in
# declaration order.
SORT_BRIEF_DOCS = NO
# If the SORT_GROUP_NAMES tag is set to YES then doxygen will sort the
# hierarchy of group names into alphabetical order. If set to NO (the default)
# the group names will appear in their defined order.
SORT_GROUP_NAMES = NO
# If the SORT_BY_SCOPE_NAME tag is set to YES, the class list will be
# sorted by fully-qualified names, including namespaces. If set to
# NO (the default), the class list will be sorted only by class name,
# not including the namespace part.
# Note: This option is not very useful if HIDE_SCOPE_NAMES is set to YES.
# Note: This option applies only to the class list, not to the
# alphabetical list.
SORT_BY_SCOPE_NAME = NO
# The GENERATE_TODOLIST tag can be used to enable (YES) or
# disable (NO) the todo list. This list is created by putting \todo
# commands in the documentation.
GENERATE_TODOLIST = NO
# The GENERATE_TESTLIST tag can be used to enable (YES) or
# disable (NO) the test list. This list is created by putting \test
# commands in the documentation.
GENERATE_TESTLIST = NO
# The GENERATE_BUGLIST tag can be used to enable (YES) or
# disable (NO) the bug list. This list is created by putting \bug
# commands in the documentation.
GENERATE_BUGLIST = NO
# The GENERATE_DEPRECATEDLIST tag can be used to enable (YES) or
# disable (NO) the deprecated list. This list is created by putting
# \deprecated commands in the documentation.
GENERATE_DEPRECATEDLIST= YES
# The ENABLED_SECTIONS tag can be used to enable conditional
# documentation sections, marked by \if sectionname ... \endif.
ENABLED_SECTIONS =
# The MAX_INITIALIZER_LINES tag determines the maximum number of lines
# the initial value of a variable or define consists of for it to appear in
# the documentation. If the initializer consists of more lines than specified
# here it will be hidden. Use a value of 0 to hide initializers completely.
# The appearance of the initializer of individual variables and defines in the
# documentation can be controlled using \showinitializer or \hideinitializer
# command in the documentation regardless of this setting.
MAX_INITIALIZER_LINES = 30
# Set the SHOW_USED_FILES tag to NO to disable the list of files generated
# at the bottom of the documentation of classes and structs. If set to YES the
# list will mention the files that were used to generate the documentation.
SHOW_USED_FILES = YES
# If the sources in your project are distributed over multiple directories
# then setting the SHOW_DIRECTORIES tag to YES will show the directory hierarchy
# in the documentation. The default is NO.
SHOW_DIRECTORIES = YES
# Set the SHOW_FILES tag to NO to disable the generation of the Files page.
# This will remove the Files entry from the Quick Index and from the
# Folder Tree View (if specified). The default is YES.
SHOW_FILES = YES
# Set the SHOW_NAMESPACES tag to NO to disable the generation of the
# Namespaces page. This will remove the Namespaces entry from the Quick Index
# and from the Folder Tree View (if specified). The default is YES.
SHOW_NAMESPACES = YES
# The FILE_VERSION_FILTER tag can be used to specify a program or script that
# doxygen should invoke to get the current version for each file (typically from
# the version control system). Doxygen will invoke the program by executing (via
# popen()) the command <command> <input-file>, where <command> is the value of
# the FILE_VERSION_FILTER tag, and <input-file> is the name of an input file
# provided by doxygen. Whatever the program writes to standard output
# is used as the file version. See the manual for examples.
FILE_VERSION_FILTER =
# The LAYOUT_FILE tag can be used to specify a layout file which will be parsed by
# doxygen. The layout file controls the global structure of the generated output files
# in an output format independent way. The create the layout file that represents
# doxygen's defaults, run doxygen with the -l option. You can optionally specify a
# file name after the option, if omitted DoxygenLayout.xml will be used as the name
# of the layout file.
LAYOUT_FILE =
#---------------------------------------------------------------------------
# configuration options related to warning and progress messages
#---------------------------------------------------------------------------
# The QUIET tag can be used to turn on/off the messages that are generated
# by doxygen. Possible values are YES and NO. If left blank NO is used.
QUIET = YES
# The WARNINGS tag can be used to turn on/off the warning messages that are
# generated by doxygen. Possible values are YES and NO. If left blank
# NO is used.
WARNINGS = YES
# If WARN_IF_UNDOCUMENTED is set to YES, then doxygen will generate warnings
# for undocumented members. If EXTRACT_ALL is set to YES then this flag will
# automatically be disabled.
WARN_IF_UNDOCUMENTED = YES
# If WARN_IF_DOC_ERROR is set to YES, doxygen will generate warnings for
# potential errors in the documentation, such as not documenting some
# parameters in a documented function, or documenting parameters that
# don't exist or using markup commands wrongly.
WARN_IF_DOC_ERROR = YES
# This WARN_NO_PARAMDOC option can be abled to get warnings for
# functions that are documented, but have no documentation for their parameters
# or return value. If set to NO (the default) doxygen will only warn about
# wrong or incomplete parameter documentation, but not about the absence of
# documentation.
WARN_NO_PARAMDOC = YES
# The WARN_FORMAT tag determines the format of the warning messages that
# doxygen can produce. The string should contain the $file, $line, and $text
# tags, which will be replaced by the file and line number from which the
# warning originated and the warning text. Optionally the format may contain
# $version, which will be replaced by the version of the file (if it could
# be obtained via FILE_VERSION_FILTER)
WARN_FORMAT = "$file:$line: $text"
# The WARN_LOGFILE tag can be used to specify a file to which warning
# and error messages should be written. If left blank the output is written
# to stderr.
WARN_LOGFILE =
#---------------------------------------------------------------------------
# configuration options related to the input files
#---------------------------------------------------------------------------
# The INPUT tag can be used to specify the files and/or directories that contain
# documented source files. You may enter file names like "myfile.cpp" or
# directories like "/usr/src/myproject". Separate the files or directories
# with spaces.
INPUT = ./
# This tag can be used to specify the character encoding of the source files
# that doxygen parses. Internally doxygen uses the UTF-8 encoding, which is
# also the default input encoding. Doxygen uses libiconv (or the iconv built
# into libc) for the transcoding. See http://www.gnu.org/software/libiconv for
# the list of possible encodings.
INPUT_ENCODING = UTF-8
# If the value of the INPUT tag contains directories, you can use the
# FILE_PATTERNS tag to specify one or more wildcard pattern (like *.cpp
# and *.h) to filter out the source-files in the directories. If left
# blank the following patterns are tested:
# *.c *.cc *.cxx *.cpp *.c++ *.java *.ii *.ixx *.ipp *.i++ *.inl *.h *.hh *.hxx
# *.hpp *.h++ *.idl *.odl *.cs *.php *.php3 *.inc *.m *.mm *.py *.f90
FILE_PATTERNS = *.h \
*.c \
*.txt
# The RECURSIVE tag can be used to turn specify whether or not subdirectories
# should be searched for input files as well. Possible values are YES and NO.
# If left blank NO is used.
RECURSIVE = YES
# The EXCLUDE tag can be used to specify files and/or directories that should
# excluded from the INPUT source files. This way you can easily exclude a
# subdirectory from a directory tree whose root is specified with the INPUT tag.
EXCLUDE =
# The EXCLUDE_SYMLINKS tag can be used select whether or not files or
# directories that are symbolic links (a Unix filesystem feature) are excluded
# from the input.
EXCLUDE_SYMLINKS = NO
# If the value of the INPUT tag contains directories, you can use the
# EXCLUDE_PATTERNS tag to specify one or more wildcard patterns to exclude
# certain files from those directories. Note that the wildcards are matched
# against the file with absolute path, so to exclude all test directories
# for example use the pattern */test/*
EXCLUDE_PATTERNS = */LowLevel/USBMode.h
# The EXCLUDE_SYMBOLS tag can be used to specify one or more symbol names
# (namespaces, classes, functions, etc.) that should be excluded from the
# output. The symbol name can be a fully qualified name, a word, or if the
# wildcard * is used, a substring. Examples: ANamespace, AClass,
# AClass::ANamespace, ANamespace::*Test
EXCLUDE_SYMBOLS = __*
# The EXAMPLE_PATH tag can be used to specify one or more files or
# directories that contain example code fragments that are included (see
# the \include command).
EXAMPLE_PATH =
# If the value of the EXAMPLE_PATH tag contains directories, you can use the
# EXAMPLE_PATTERNS tag to specify one or more wildcard pattern (like *.cpp
# and *.h) to filter out the source-files in the directories. If left
# blank all files are included.
EXAMPLE_PATTERNS = *
# If the EXAMPLE_RECURSIVE tag is set to YES then subdirectories will be
# searched for input files to be used with the \include or \dontinclude
# commands irrespective of the value of the RECURSIVE tag.
# Possible values are YES and NO. If left blank NO is used.
EXAMPLE_RECURSIVE = NO
# The IMAGE_PATH tag can be used to specify one or more files or
# directories that contain image that are included in the documentation (see
# the \image command).
IMAGE_PATH =
# The INPUT_FILTER tag can be used to specify a program that doxygen should
# invoke to filter for each input file. Doxygen will invoke the filter program
# by executing (via popen()) the command <filter> <input-file>, where <filter>
# is the value of the INPUT_FILTER tag, and <input-file> is the name of an
# input file. Doxygen will then use the output that the filter program writes
# to standard output. If FILTER_PATTERNS is specified, this tag will be
# ignored.
INPUT_FILTER =
# The FILTER_PATTERNS tag can be used to specify filters on a per file pattern
# basis. Doxygen will compare the file name with each pattern and apply the
# filter if there is a match. The filters are a list of the form:
# pattern=filter (like *.cpp=my_cpp_filter). See INPUT_FILTER for further
# info on how filters are used. If FILTER_PATTERNS is empty, INPUT_FILTER
# is applied to all files.
FILTER_PATTERNS =
# If the FILTER_SOURCE_FILES tag is set to YES, the input filter (if set using
# INPUT_FILTER) will be used to filter the input files when producing source
# files to browse (i.e. when SOURCE_BROWSER is set to YES).
FILTER_SOURCE_FILES = NO
#---------------------------------------------------------------------------
# configuration options related to source browsing
#---------------------------------------------------------------------------
# If the SOURCE_BROWSER tag is set to YES then a list of source files will
# be generated. Documented entities will be cross-referenced with these sources.
# Note: To get rid of all source code in the generated output, make sure also
# VERBATIM_HEADERS is set to NO.
SOURCE_BROWSER = NO
# Setting the INLINE_SOURCES tag to YES will include the body
# of functions and classes directly in the documentation.
INLINE_SOURCES = NO
# Setting the STRIP_CODE_COMMENTS tag to YES (the default) will instruct
# doxygen to hide any special comment blocks from generated source code
# fragments. Normal C and C++ comments will always remain visible.
STRIP_CODE_COMMENTS = YES
# If the REFERENCED_BY_RELATION tag is set to YES
# then for each documented function all documented
# functions referencing it will be listed.
REFERENCED_BY_RELATION = NO
# If the REFERENCES_RELATION tag is set to YES
# then for each documented function all documented entities
# called/used by that function will be listed.
REFERENCES_RELATION = NO
# If the REFERENCES_LINK_SOURCE tag is set to YES (the default)
# and SOURCE_BROWSER tag is set to YES, then the hyperlinks from
# functions in REFERENCES_RELATION and REFERENCED_BY_RELATION lists will
# link to the source code. Otherwise they will link to the documentstion.
REFERENCES_LINK_SOURCE = NO
# If the USE_HTAGS tag is set to YES then the references to source code
# will point to the HTML generated by the htags(1) tool instead of doxygen
# built-in source browser. The htags tool is part of GNU's global source
# tagging system (see http://www.gnu.org/software/global/global.html). You
# will need version 4.8.6 or higher.
USE_HTAGS = NO
# If the VERBATIM_HEADERS tag is set to YES (the default) then Doxygen
# will generate a verbatim copy of the header file for each class for
# which an include is specified. Set to NO to disable this.
VERBATIM_HEADERS = NO
#---------------------------------------------------------------------------
# configuration options related to the alphabetical class index
#---------------------------------------------------------------------------
# If the ALPHABETICAL_INDEX tag is set to YES, an alphabetical index
# of all compounds will be generated. Enable this if the project
# contains a lot of classes, structs, unions or interfaces.
ALPHABETICAL_INDEX = YES
# If the alphabetical index is enabled (see ALPHABETICAL_INDEX) then
# the COLS_IN_ALPHA_INDEX tag can be used to specify the number of columns
# in which this list will be split (can be a number in the range [1..20])
COLS_IN_ALPHA_INDEX = 5
# In case all classes in a project start with a common prefix, all
# classes will be put under the same header in the alphabetical index.
# The IGNORE_PREFIX tag can be used to specify one or more prefixes that
# should be ignored while generating the index headers.
IGNORE_PREFIX =
#---------------------------------------------------------------------------
# configuration options related to the HTML output
#---------------------------------------------------------------------------
# If the GENERATE_HTML tag is set to YES (the default) Doxygen will
# generate HTML output.
GENERATE_HTML = YES
# The HTML_OUTPUT tag is used to specify where the HTML docs will be put.
# If a relative path is entered the value of OUTPUT_DIRECTORY will be
# put in front of it. If left blank `html' will be used as the default path.
HTML_OUTPUT = html
# The HTML_FILE_EXTENSION tag can be used to specify the file extension for
# each generated HTML page (for example: .htm,.php,.asp). If it is left blank
# doxygen will generate files with .html extension.
HTML_FILE_EXTENSION = .html
# The HTML_HEADER tag can be used to specify a personal HTML header for
# each generated HTML page. If it is left blank doxygen will generate a
# standard header.
HTML_HEADER =
# The HTML_FOOTER tag can be used to specify a personal HTML footer for
# each generated HTML page. If it is left blank doxygen will generate a
# standard footer.
HTML_FOOTER =
# The HTML_STYLESHEET tag can be used to specify a user-defined cascading
# style sheet that is used by each HTML page. It can be used to
# fine-tune the look of the HTML output. If the tag is left blank doxygen
# will generate a default style sheet. Note that doxygen will try to copy
# the style sheet file to the HTML output directory, so don't put your own
# stylesheet in the HTML output directory as well, or it will be erased!
HTML_STYLESHEET =
# If the HTML_ALIGN_MEMBERS tag is set to YES, the members of classes,
# files or namespaces will be aligned in HTML using tables. If set to
# NO a bullet list will be used.
HTML_ALIGN_MEMBERS = YES
# If the HTML_DYNAMIC_SECTIONS tag is set to YES then the generated HTML
# documentation will contain sections that can be hidden and shown after the
# page has loaded. For this to work a browser that supports
# JavaScript and DHTML is required (for instance Mozilla 1.0+, Firefox
# Netscape 6.0+, Internet explorer 5.0+, Konqueror, or Safari).
HTML_DYNAMIC_SECTIONS = YES
# If the GENERATE_DOCSET tag is set to YES, additional index files
# will be generated that can be used as input for Apple's Xcode 3
# integrated development environment, introduced with OSX 10.5 (Leopard).
# To create a documentation set, doxygen will generate a Makefile in the
# HTML output directory. Running make will produce the docset in that
# directory and running "make install" will install the docset in
# ~/Library/Developer/Shared/Documentation/DocSets so that Xcode will find
# it at startup.
# See http://developer.apple.com/tools/creatingdocsetswithdoxygen.html for more information.
GENERATE_DOCSET = NO
# When GENERATE_DOCSET tag is set to YES, this tag determines the name of the
# feed. A documentation feed provides an umbrella under which multiple
# documentation sets from a single provider (such as a company or product suite)
# can be grouped.
DOCSET_FEEDNAME = "Doxygen generated docs"
# When GENERATE_DOCSET tag is set to YES, this tag specifies a string that
# should uniquely identify the documentation set bundle. This should be a
# reverse domain-name style string, e.g. com.mycompany.MyDocSet. Doxygen
# will append .docset to the name.
DOCSET_BUNDLE_ID = org.doxygen.Project
# If the GENERATE_HTMLHELP tag is set to YES, additional index files
# will be generated that can be used as input for tools like the
# Microsoft HTML help workshop to generate a compiled HTML help file (.chm)
# of the generated HTML documentation.
GENERATE_HTMLHELP = NO
# If the GENERATE_HTMLHELP tag is set to YES, the CHM_FILE tag can
# be used to specify the file name of the resulting .chm file. You
# can add a path in front of the file if the result should not be
# written to the html output directory.
CHM_FILE =
# If the GENERATE_HTMLHELP tag is set to YES, the HHC_LOCATION tag can
# be used to specify the location (absolute path including file name) of
# the HTML help compiler (hhc.exe). If non-empty doxygen will try to run
# the HTML help compiler on the generated index.hhp.
HHC_LOCATION =
# If the GENERATE_HTMLHELP tag is set to YES, the GENERATE_CHI flag
# controls if a separate .chi index file is generated (YES) or that
# it should be included in the master .chm file (NO).
GENERATE_CHI = NO
# If the GENERATE_HTMLHELP tag is set to YES, the CHM_INDEX_ENCODING
# is used to encode HtmlHelp index (hhk), content (hhc) and project file
# content.
CHM_INDEX_ENCODING =
# If the GENERATE_HTMLHELP tag is set to YES, the BINARY_TOC flag
# controls whether a binary table of contents is generated (YES) or a
# normal table of contents (NO) in the .chm file.
BINARY_TOC = NO
# The TOC_EXPAND flag can be set to YES to add extra items for group members
# to the contents of the HTML help documentation and to the tree view.
TOC_EXPAND = YES
# If the GENERATE_QHP tag is set to YES and both QHP_NAMESPACE and QHP_VIRTUAL_FOLDER
# are set, an additional index file will be generated that can be used as input for
# Qt's qhelpgenerator to generate a Qt Compressed Help (.qch) of the generated
# HTML documentation.
GENERATE_QHP = NO
# If the QHG_LOCATION tag is specified, the QCH_FILE tag can
# be used to specify the file name of the resulting .qch file.
# The path specified is relative to the HTML output folder.
QCH_FILE =
# The QHP_NAMESPACE tag specifies the namespace to use when generating
# Qt Help Project output. For more information please see
# <a href="http://doc.trolltech.com/qthelpproject.html#namespace">Qt Help Project / Namespace</a>.
QHP_NAMESPACE = org.doxygen.Project
# The QHP_VIRTUAL_FOLDER tag specifies the namespace to use when generating
# Qt Help Project output. For more information please see
# <a href="http://doc.trolltech.com/qthelpproject.html#virtual-folders">Qt Help Project / Virtual Folders</a>.
QHP_VIRTUAL_FOLDER = doc
# If the GENERATE_QHP tag is set to YES, the QHG_LOCATION tag can
# be used to specify the location of Qt's qhelpgenerator.
# If non-empty doxygen will try to run qhelpgenerator on the generated
# .qhp file .
QHG_LOCATION =
# The DISABLE_INDEX tag can be used to turn on/off the condensed index at
# top of each HTML page. The value NO (the default) enables the index and
# the value YES disables it.
DISABLE_INDEX = NO
# This tag can be used to set the number of enum values (range [1..20])
# that doxygen will group on one line in the generated HTML documentation.
ENUM_VALUES_PER_LINE = 1
# The GENERATE_TREEVIEW tag is used to specify whether a tree-like index
# structure should be generated to display hierarchical information.
# If the tag value is set to FRAME, a side panel will be generated
# containing a tree-like index structure (just like the one that
# is generated for HTML Help). For this to work a browser that supports
# JavaScript, DHTML, CSS and frames is required (for instance Mozilla 1.0+,
# Netscape 6.0+, Internet explorer 5.0+, or Konqueror). Windows users are
# probably better off using the HTML help feature. Other possible values
# for this tag are: HIERARCHIES, which will generate the Groups, Directories,
# and Class Hierarchy pages using a tree view instead of an ordered list;
# ALL, which combines the behavior of FRAME and HIERARCHIES; and NONE, which
# disables this behavior completely. For backwards compatibility with previous
# releases of Doxygen, the values YES and NO are equivalent to FRAME and NONE
# respectively.
GENERATE_TREEVIEW = YES
# If the treeview is enabled (see GENERATE_TREEVIEW) then this tag can be
# used to set the initial width (in pixels) of the frame in which the tree
# is shown.
TREEVIEW_WIDTH = 250
# Use this tag to change the font size of Latex formulas included
# as images in the HTML documentation. The default is 10. Note that
# when you change the font size after a successful doxygen run you need
# to manually remove any form_*.png images from the HTML output directory
# to force them to be regenerated.
FORMULA_FONTSIZE = 10
#---------------------------------------------------------------------------
# configuration options related to the LaTeX output
#---------------------------------------------------------------------------
# If the GENERATE_LATEX tag is set to YES (the default) Doxygen will
# generate Latex output.
GENERATE_LATEX = NO
# The LATEX_OUTPUT tag is used to specify where the LaTeX docs will be put.
# If a relative path is entered the value of OUTPUT_DIRECTORY will be
# put in front of it. If left blank `latex' will be used as the default path.
LATEX_OUTPUT = latex
# The LATEX_CMD_NAME tag can be used to specify the LaTeX command name to be
# invoked. If left blank `latex' will be used as the default command name.
LATEX_CMD_NAME = latex
# The MAKEINDEX_CMD_NAME tag can be used to specify the command name to
# generate index for LaTeX. If left blank `makeindex' will be used as the
# default command name.
MAKEINDEX_CMD_NAME = makeindex
# If the COMPACT_LATEX tag is set to YES Doxygen generates more compact
# LaTeX documents. This may be useful for small projects and may help to
# save some trees in general.
COMPACT_LATEX = NO
# The PAPER_TYPE tag can be used to set the paper type that is used
# by the printer. Possible values are: a4, a4wide, letter, legal and
# executive. If left blank a4wide will be used.
PAPER_TYPE = a4wide
# The EXTRA_PACKAGES tag can be to specify one or more names of LaTeX
# packages that should be included in the LaTeX output.
EXTRA_PACKAGES =
# The LATEX_HEADER tag can be used to specify a personal LaTeX header for
# the generated latex document. The header should contain everything until
# the first chapter. If it is left blank doxygen will generate a
# standard header. Notice: only use this tag if you know what you are doing!
LATEX_HEADER =
# If the PDF_HYPERLINKS tag is set to YES, the LaTeX that is generated
# is prepared for conversion to pdf (using ps2pdf). The pdf file will
# contain links (just like the HTML output) instead of page references
# This makes the output suitable for online browsing using a pdf viewer.
PDF_HYPERLINKS = YES
# If the USE_PDFLATEX tag is set to YES, pdflatex will be used instead of
# plain latex in the generated Makefile. Set this option to YES to get a
# higher quality PDF documentation.
USE_PDFLATEX = YES
# If the LATEX_BATCHMODE tag is set to YES, doxygen will add the \\batchmode.
# command to the generated LaTeX files. This will instruct LaTeX to keep
# running if errors occur, instead of asking the user for help.
# This option is also used when generating formulas in HTML.
LATEX_BATCHMODE = NO
# If LATEX_HIDE_INDICES is set to YES then doxygen will not
# include the index chapters (such as File Index, Compound Index, etc.)
# in the output.
LATEX_HIDE_INDICES = NO
#---------------------------------------------------------------------------
# configuration options related to the RTF output
#---------------------------------------------------------------------------
# If the GENERATE_RTF tag is set to YES Doxygen will generate RTF output
# The RTF output is optimized for Word 97 and may not look very pretty with
# other RTF readers or editors.
GENERATE_RTF = NO
# The RTF_OUTPUT tag is used to specify where the RTF docs will be put.
# If a relative path is entered the value of OUTPUT_DIRECTORY will be
# put in front of it. If left blank `rtf' will be used as the default path.
RTF_OUTPUT = rtf
# If the COMPACT_RTF tag is set to YES Doxygen generates more compact
# RTF documents. This may be useful for small projects and may help to
# save some trees in general.
COMPACT_RTF = NO
# If the RTF_HYPERLINKS tag is set to YES, the RTF that is generated
# will contain hyperlink fields. The RTF file will
# contain links (just like the HTML output) instead of page references.
# This makes the output suitable for online browsing using WORD or other
# programs which support those fields.
# Note: wordpad (write) and others do not support links.
RTF_HYPERLINKS = NO
# Load stylesheet definitions from file. Syntax is similar to doxygen's
# config file, i.e. a series of assignments. You only have to provide
# replacements, missing definitions are set to their default value.
RTF_STYLESHEET_FILE =
# Set optional variables used in the generation of an rtf document.
# Syntax is similar to doxygen's config file.
RTF_EXTENSIONS_FILE =
#---------------------------------------------------------------------------
# configuration options related to the man page output
#---------------------------------------------------------------------------
# If the GENERATE_MAN tag is set to YES (the default) Doxygen will
# generate man pages
GENERATE_MAN = NO
# The MAN_OUTPUT tag is used to specify where the man pages will be put.
# If a relative path is entered the value of OUTPUT_DIRECTORY will be
# put in front of it. If left blank `man' will be used as the default path.
MAN_OUTPUT = man
# The MAN_EXTENSION tag determines the extension that is added to
# the generated man pages (default is the subroutine's section .3)
MAN_EXTENSION = .3
# If the MAN_LINKS tag is set to YES and Doxygen generates man output,
# then it will generate one additional man file for each entity
# documented in the real man page(s). These additional files
# only source the real man page, but without them the man command
# would be unable to find the correct page. The default is NO.
MAN_LINKS = NO
#---------------------------------------------------------------------------
# configuration options related to the XML output
#---------------------------------------------------------------------------
# If the GENERATE_XML tag is set to YES Doxygen will
# generate an XML file that captures the structure of
# the code including all documentation.
GENERATE_XML = NO
# The XML_OUTPUT tag is used to specify where the XML pages will be put.
# If a relative path is entered the value of OUTPUT_DIRECTORY will be
# put in front of it. If left blank `xml' will be used as the default path.
XML_OUTPUT = xml
# The XML_SCHEMA tag can be used to specify an XML schema,
# which can be used by a validating XML parser to check the
# syntax of the XML files.
XML_SCHEMA =
# The XML_DTD tag can be used to specify an XML DTD,
# which can be used by a validating XML parser to check the
# syntax of the XML files.
XML_DTD =
# If the XML_PROGRAMLISTING tag is set to YES Doxygen will
# dump the program listings (including syntax highlighting
# and cross-referencing information) to the XML output. Note that
# enabling this will significantly increase the size of the XML output.
XML_PROGRAMLISTING = YES
#---------------------------------------------------------------------------
# configuration options for the AutoGen Definitions output
#---------------------------------------------------------------------------
# If the GENERATE_AUTOGEN_DEF tag is set to YES Doxygen will
# generate an AutoGen Definitions (see autogen.sf.net) file
# that captures the structure of the code including all
# documentation. Note that this feature is still experimental
# and incomplete at the moment.
GENERATE_AUTOGEN_DEF = NO
#---------------------------------------------------------------------------
# configuration options related to the Perl module output
#---------------------------------------------------------------------------
# If the GENERATE_PERLMOD tag is set to YES Doxygen will
# generate a Perl module file that captures the structure of
# the code including all documentation. Note that this
# feature is still experimental and incomplete at the
# moment.
GENERATE_PERLMOD = NO
# If the PERLMOD_LATEX tag is set to YES Doxygen will generate
# the necessary Makefile rules, Perl scripts and LaTeX code to be able
# to generate PDF and DVI output from the Perl module output.
PERLMOD_LATEX = NO
# If the PERLMOD_PRETTY tag is set to YES the Perl module output will be
# nicely formatted so it can be parsed by a human reader. This is useful
# if you want to understand what is going on. On the other hand, if this
# tag is set to NO the size of the Perl module output will be much smaller
# and Perl will parse it just the same.
PERLMOD_PRETTY = YES
# The names of the make variables in the generated doxyrules.make file
# are prefixed with the string contained in PERLMOD_MAKEVAR_PREFIX.
# This is useful so different doxyrules.make files included by the same
# Makefile don't overwrite each other's variables.
PERLMOD_MAKEVAR_PREFIX =
#---------------------------------------------------------------------------
# Configuration options related to the preprocessor
#---------------------------------------------------------------------------
# If the ENABLE_PREPROCESSING tag is set to YES (the default) Doxygen will
# evaluate all C-preprocessor directives found in the sources and include
# files.
ENABLE_PREPROCESSING = YES
# If the MACRO_EXPANSION tag is set to YES Doxygen will expand all macro
# names in the source code. If set to NO (the default) only conditional
# compilation will be performed. Macro expansion can be done in a controlled
# way by setting EXPAND_ONLY_PREDEF to YES.
MACRO_EXPANSION = YES
# If the EXPAND_ONLY_PREDEF and MACRO_EXPANSION tags are both set to YES
# then the macro expansion is limited to the macros specified with the
# PREDEFINED and EXPAND_AS_DEFINED tags.
EXPAND_ONLY_PREDEF = YES
# If the SEARCH_INCLUDES tag is set to YES (the default) the includes files
# in the INCLUDE_PATH (see below) will be search if a #include is found.
SEARCH_INCLUDES = YES
# The INCLUDE_PATH tag can be used to specify one or more directories that
# contain include files that are not input files but should be processed by
# the preprocessor.
INCLUDE_PATH =
# You can use the INCLUDE_FILE_PATTERNS tag to specify one or more wildcard
# patterns (like *.h and *.hpp) to filter out the header-files in the
# directories. If left blank, the patterns specified with FILE_PATTERNS will
# be used.
INCLUDE_FILE_PATTERNS =
# The PREDEFINED tag can be used to specify one or more macro names that
# are defined before the preprocessor is started (similar to the -D option of
# gcc). The argument of the tag is a list of macros of the form: name
# or name=definition (no spaces). If the definition and the = are
# omitted =1 is assumed. To prevent a macro definition from being
# undefined via #undef or recursively expanded use the := operator
# instead of the = operator.
PREDEFINED = __DOXYGEN__
# If the MACRO_EXPANSION and EXPAND_ONLY_PREDEF tags are set to YES then
# this tag can be used to specify a list of macro names that should be expanded.
# The macro definition that is found in the sources will be used.
# Use the PREDEFINED tag if you want to use a different macro definition.
EXPAND_AS_DEFINED = BUTTLOADTAG
# If the SKIP_FUNCTION_MACROS tag is set to YES (the default) then
# doxygen's preprocessor will remove all function-like macros that are alone
# on a line, have an all uppercase name, and do not end with a semicolon. Such
# function macros are typically used for boiler-plate code, and will confuse
# the parser if not removed.
SKIP_FUNCTION_MACROS = YES
#---------------------------------------------------------------------------
# Configuration::additions related to external references
#---------------------------------------------------------------------------
# The TAGFILES option can be used to specify one or more tagfiles.
# Optionally an initial location of the external documentation
# can be added for each tagfile. The format of a tag file without
# this location is as follows:
# TAGFILES = file1 file2 ...
# Adding location for the tag files is done as follows:
# TAGFILES = file1=loc1 "file2 = loc2" ...
# where "loc1" and "loc2" can be relative or absolute paths or
# URLs. If a location is present for each tag, the installdox tool
# does not have to be run to correct the links.
# Note that each tag file must have a unique name
# (where the name does NOT include the path)
# If a tag file is not located in the directory in which doxygen
# is run, you must also specify the path to the tagfile here.
TAGFILES =
# When a file name is specified after GENERATE_TAGFILE, doxygen will create
# a tag file that is based on the input files it reads.
GENERATE_TAGFILE =
# If the ALLEXTERNALS tag is set to YES all external classes will be listed
# in the class index. If set to NO only the inherited external classes
# will be listed.
ALLEXTERNALS = NO
# If the EXTERNAL_GROUPS tag is set to YES all external groups will be listed
# in the modules index. If set to NO, only the current project's groups will
# be listed.
EXTERNAL_GROUPS = YES
# The PERL_PATH should be the absolute path and name of the perl script
# interpreter (i.e. the result of `which perl').
PERL_PATH = /usr/bin/perl
#---------------------------------------------------------------------------
# Configuration options related to the dot tool
#---------------------------------------------------------------------------
# If the CLASS_DIAGRAMS tag is set to YES (the default) Doxygen will
# generate a inheritance diagram (in HTML, RTF and LaTeX) for classes with base
# or super classes. Setting the tag to NO turns the diagrams off. Note that
# this option is superseded by the HAVE_DOT option below. This is only a
# fallback. It is recommended to install and use dot, since it yields more
# powerful graphs.
CLASS_DIAGRAMS = NO
# You can define message sequence charts within doxygen comments using the \msc
# command. Doxygen will then run the mscgen tool (see
# http://www.mcternan.me.uk/mscgen/) to produce the chart and insert it in the
# documentation. The MSCGEN_PATH tag allows you to specify the directory where
# the mscgen tool resides. If left empty the tool is assumed to be found in the
# default search path.
MSCGEN_PATH =
# If set to YES, the inheritance and collaboration graphs will hide
# inheritance and usage relations if the target is undocumented
# or is not a class.
HIDE_UNDOC_RELATIONS = YES
# If you set the HAVE_DOT tag to YES then doxygen will assume the dot tool is
# available from the path. This tool is part of Graphviz, a graph visualization
# toolkit from AT&T and Lucent Bell Labs. The other options in this section
# have no effect if this option is set to NO (the default)
HAVE_DOT = NO
# By default doxygen will write a font called FreeSans.ttf to the output
# directory and reference it in all dot files that doxygen generates. This
# font does not include all possible unicode characters however, so when you need
# these (or just want a differently looking font) you can specify the font name
# using DOT_FONTNAME. You need need to make sure dot is able to find the font,
# which can be done by putting it in a standard location or by setting the
# DOTFONTPATH environment variable or by setting DOT_FONTPATH to the directory
# containing the font.
DOT_FONTNAME = FreeSans
# The DOT_FONTSIZE tag can be used to set the size of the font of dot graphs.
# The default size is 10pt.
DOT_FONTSIZE = 10
# By default doxygen will tell dot to use the output directory to look for the
# FreeSans.ttf font (which doxygen will put there itself). If you specify a
# different font using DOT_FONTNAME you can set the path where dot
# can find it using this tag.
DOT_FONTPATH =
# If the CLASS_GRAPH and HAVE_DOT tags are set to YES then doxygen
# will generate a graph for each documented class showing the direct and
# indirect inheritance relations. Setting this tag to YES will force the
# the CLASS_DIAGRAMS tag to NO.
CLASS_GRAPH = NO
# If the COLLABORATION_GRAPH and HAVE_DOT tags are set to YES then doxygen
# will generate a graph for each documented class showing the direct and
# indirect implementation dependencies (inheritance, containment, and
# class references variables) of the class with other documented classes.
COLLABORATION_GRAPH = NO
# If the GROUP_GRAPHS and HAVE_DOT tags are set to YES then doxygen
# will generate a graph for groups, showing the direct groups dependencies
GROUP_GRAPHS = NO
# If the UML_LOOK tag is set to YES doxygen will generate inheritance and
# collaboration diagrams in a style similar to the OMG's Unified Modeling
# Language.
UML_LOOK = NO
# If set to YES, the inheritance and collaboration graphs will show the
# relations between templates and their instances.
TEMPLATE_RELATIONS = NO
# If the ENABLE_PREPROCESSING, SEARCH_INCLUDES, INCLUDE_GRAPH, and HAVE_DOT
# tags are set to YES then doxygen will generate a graph for each documented
# file showing the direct and indirect include dependencies of the file with
# other documented files.
INCLUDE_GRAPH = NO
# If the ENABLE_PREPROCESSING, SEARCH_INCLUDES, INCLUDED_BY_GRAPH, and
# HAVE_DOT tags are set to YES then doxygen will generate a graph for each
# documented header file showing the documented files that directly or
# indirectly include this file.
INCLUDED_BY_GRAPH = NO
# If the CALL_GRAPH and HAVE_DOT options are set to YES then
# doxygen will generate a call dependency graph for every global function
# or class method. Note that enabling this option will significantly increase
# the time of a run. So in most cases it will be better to enable call graphs
# for selected functions only using the \callgraph command.
CALL_GRAPH = NO
# If the CALLER_GRAPH and HAVE_DOT tags are set to YES then
# doxygen will generate a caller dependency graph for every global function
# or class method. Note that enabling this option will significantly increase
# the time of a run. So in most cases it will be better to enable caller
# graphs for selected functions only using the \callergraph command.
CALLER_GRAPH = NO
# If the GRAPHICAL_HIERARCHY and HAVE_DOT tags are set to YES then doxygen
# will graphical hierarchy of all classes instead of a textual one.
GRAPHICAL_HIERARCHY = NO
# If the DIRECTORY_GRAPH, SHOW_DIRECTORIES and HAVE_DOT tags are set to YES
# then doxygen will show the dependencies a directory has on other directories
# in a graphical way. The dependency relations are determined by the #include
# relations between the files in the directories.
DIRECTORY_GRAPH = NO
# The DOT_IMAGE_FORMAT tag can be used to set the image format of the images
# generated by dot. Possible values are png, jpg, or gif
# If left blank png will be used.
DOT_IMAGE_FORMAT = png
# The tag DOT_PATH can be used to specify the path where the dot tool can be
# found. If left blank, it is assumed the dot tool can be found in the path.
DOT_PATH = "C:/Program Files/Graphviz2.18/bin"
# The DOTFILE_DIRS tag can be used to specify one or more directories that
# contain dot files that are included in the documentation (see the
# \dotfile command).
DOTFILE_DIRS =
# The DOT_GRAPH_MAX_NODES tag can be used to set the maximum number of
# nodes that will be shown in the graph. If the number of nodes in a graph
# becomes larger than this value, doxygen will truncate the graph, which is
# visualized by representing a node as a red box. Note that doxygen if the
# number of direct children of the root node in a graph is already larger than
# DOT_GRAPH_MAX_NODES then the graph will not be shown at all. Also note
# that the size of a graph can be further restricted by MAX_DOT_GRAPH_DEPTH.
DOT_GRAPH_MAX_NODES = 15
# The MAX_DOT_GRAPH_DEPTH tag can be used to set the maximum depth of the
# graphs generated by dot. A depth value of 3 means that only nodes reachable
# from the root by following a path via at most 3 edges will be shown. Nodes
# that lay further from the root node will be omitted. Note that setting this
# option to 1 or 2 may greatly reduce the computation time needed for large
# code bases. Also note that the size of a graph can be further restricted by
# DOT_GRAPH_MAX_NODES. Using a depth of 0 means no depth restriction.
MAX_DOT_GRAPH_DEPTH = 2
# Set the DOT_TRANSPARENT tag to YES to generate images with a transparent
# background. This is disabled by default, because dot on Windows does not
# seem to support this out of the box. Warning: Depending on the platform used,
# enabling this option may lead to badly anti-aliased labels on the edges of
# a graph (i.e. they become hard to read).
DOT_TRANSPARENT = YES
# Set the DOT_MULTI_TARGETS tag to YES allow dot to generate multiple output
# files in one run (i.e. multiple -o and -T options on the command line). This
# makes dot run faster, but since only newer versions of dot (>1.8.10)
# support this, this feature is disabled by default.
DOT_MULTI_TARGETS = NO
# If the GENERATE_LEGEND tag is set to YES (the default) Doxygen will
# generate a legend page explaining the meaning of the various boxes and
# arrows in the dot generated graphs.
GENERATE_LEGEND = YES
# If the DOT_CLEANUP tag is set to YES (the default) Doxygen will
# remove the intermediate dot files that are used to generate
# the various graphs.
DOT_CLEANUP = YES
#---------------------------------------------------------------------------
# Configuration::additions related to the search engine
#---------------------------------------------------------------------------
# The SEARCHENGINE tag specifies whether or not a search engine should be
# used. If set to NO the values of all tags below this one will be ignored.
SEARCHENGINE = NO

@ -0,0 +1,55 @@
; Windows LUFA USB to Serial Setup File
; Copyright (c) 2000 Microsoft Corporation
[Version]
Signature="$Windows NT$"
Class=Ports
ClassGuid={4D36E978-E325-11CE-BFC1-08002BE10318}
Provider=%COMPANY%
LayoutFile=layout.inf
DriverVer=06/06/2006,1.0.0.0
[Manufacturer]
%MFGNAME% = ManufName
[DestinationDirs]
DefaultDestDir=12
[ManufName]
%Modem3% = Modem3, USB\VID_03EB&PID_204B
;------------------------------------------------------------------------------
; Windows 2000/XP Sections
;------------------------------------------------------------------------------
[Modem3.nt]
CopyFiles=USBModemCopyFileSection
AddReg=Modem3.nt.AddReg
[USBModemCopyFileSection]
usbser.sys,,,0x20
[Modem3.nt.AddReg]
HKR,,DevLoader,,*ntkern
HKR,,NTMPDriver,,usbser.sys
HKR,,EnumPropPages32,,"MsPorts.dll,SerialPortPropPageProvider"
[Modem3.nt.Services]
AddService=usbser, 0x00000002, DriverService
[DriverService]
DisplayName=%SERVICE%
ServiceType=1
StartType=3
ErrorControl=1
ServiceBinary=%12%\usbser.sys
;------------------------------------------------------------------------------
; String Definitions
;------------------------------------------------------------------------------
[Strings]
COMPANY="LUFA Library"
MFGNAME="Dean Camera"
Modem3="USB Virtual Serial Port"
SERVICE="USB Virtual Serial Port CDC Driver"

@ -0,0 +1,120 @@
/*
LUFA Library
Copyright (C) Dean Camera, 2009.
dean [at] fourwalledcubicle [dot] com
www.fourwalledcubicle.com
*/
/*
Copyright 2009 Dean Camera (dean [at] fourwalledcubicle [dot] com)
Permission to use, copy, modify, and distribute this software
and its documentation for any purpose and without fee is hereby
granted, provided that the above copyright notice appear in all
copies and that both that the copyright notice and this
permission notice and warranty disclaimer appear in supporting
documentation, and that the name of the author not be used in
advertising or publicity pertaining to distribution of the
software without specific, written prior permission.
The author disclaim all warranties with regard to this
software, including all implied warranties of merchantability
and fitness. In no event shall the author be liable for any
special, indirect or consequential damages or any damages
whatsoever resulting from loss of use, data or profits, whether
in an action of contract, negligence or other tortious action,
arising out of or in connection with the use or performance of
this software.
*/
#include "RingBuff.h"
void Buffer_Initialize(RingBuff_t* Buffer)
{
BUFF_ATOMIC_BLOCK
{
Buffer->InPtr = (RingBuff_Data_t*)&Buffer->Buffer;
Buffer->OutPtr = (RingBuff_Data_t*)&Buffer->Buffer;
Buffer->Elements = 0;
}
}
void Buffer_StoreElement(RingBuff_t* Buffer, RingBuff_Data_t Data)
{
BUFF_ATOMIC_BLOCK
{
#if defined(BUFF_DROPOLD)
if (Buffer->Elements == BUFF_LENGTH)
{
Buffer->OutPtr++;
if (Buffer->OutPtr == &Buffer->Buffer[BUFF_LENGTH])
Buffer->OutPtr = (RingBuff_Data_t*)&Buffer->Buffer;
}
else
{
Buffer->Elements++;
}
#elif defined(BUFF_DROPNEW)
if (Buffer->Elements == BUFF_LENGTH)
return;
Buffer->Elements++;
#elif defined(BUFF_NODROPCHECK)
Buffer->Elements++;
#endif
*(Buffer->InPtr) = Data;
Buffer->InPtr++;
if (Buffer->InPtr == &Buffer->Buffer[BUFF_LENGTH])
Buffer->InPtr = (RingBuff_Data_t*)&Buffer->Buffer;
}
}
RingBuff_Data_t Buffer_GetElement(RingBuff_t* Buffer)
{
RingBuff_Data_t BuffData;
BUFF_ATOMIC_BLOCK
{
#if defined(BUFF_EMPTYRETURNSZERO)
if (!(Buffer->Elements))
return 0;
#elif !defined(BUFF_NOEMPTYCHECK)
#error No empty buffer check behaviour specified.
#endif
BuffData = *(Buffer->OutPtr);
Buffer->OutPtr++;
Buffer->Elements--;
if (Buffer->OutPtr == &Buffer->Buffer[BUFF_LENGTH])
Buffer->OutPtr = (RingBuff_Data_t*)&Buffer->Buffer;
}
return BuffData;
}
#if defined(BUFF_USEPEEK)
RingBuff_Data_t Buffer_PeekElement(const RingBuff_t* Buffer)
{
RingBuff_Data_t BuffData;
BUFF_ATOMIC_BLOCK
{
#if defined(BUFF_EMPTYRETURNSZERO)
if (!(Buffer->Elements))
return 0;
#elif !defined(BUFF_NOEMPTYCHECK)
#error No empty buffer check behaviour specified.
#endif
BuffData = *(Buffer->OutPtr);
}
return BuffData;
}
#endif

@ -0,0 +1,116 @@
/*
LUFA Library
Copyright (C) Dean Camera, 2009.
dean [at] fourwalledcubicle [dot] com
www.fourwalledcubicle.com
*/
/*
Copyright 2009 Dean Camera (dean [at] fourwalledcubicle [dot] com)
Permission to use, copy, modify, and distribute this software
and its documentation for any purpose and without fee is hereby
granted, provided that the above copyright notice appear in all
copies and that both that the copyright notice and this
permission notice and warranty disclaimer appear in supporting
documentation, and that the name of the author not be used in
advertising or publicity pertaining to distribution of the
software without specific, written prior permission.
The author disclaim all warranties with regard to this
software, including all implied warranties of merchantability
and fitness. In no event shall the author be liable for any
special, indirect or consequential damages or any damages
whatsoever resulting from loss of use, data or profits, whether
in an action of contract, negligence or other tortious action,
arising out of or in connection with the use or performance of
this software.
*/
/* Buffer Configuration: */
/* Buffer length - select static size of created ringbuffers: */
#define BUFF_STATICSIZE 128 // Set to the static ringbuffer size for all ringbuffers (place size after define)
/* Volatile mode - uncomment to make buffers volatile, for use in ISRs, etc: */
#define BUFF_VOLATILE // Uncomment to cause all ring buffers to become volatile (and atomic if multi-byte) in access
/* Drop mode - select behaviour when Buffer_StoreElement called on a full buffer: */
#define BUFF_DROPOLD // Uncomment to cause full ring buffers to drop the oldest character to make space when full
// #define BUFF_DROPNEW // Uncomment to cause full ring buffers to drop the new character when full
// #define BUFF_NODROPCHECK // Uncomment to ignore full ring buffer checks - checking left to user!
/* Underflow behaviour - select behaviour when Buffer_GetElement is called with an empty ringbuffer: */
//#define BUFF_EMPTYRETURNSZERO // Uncomment to return 0 when an empty ringbuffer is read
#define BUFF_NOEMPTYCHECK // Uncomment to disable checking of empty ringbuffers - checking left to user!
/* Buffer storage type - set the datatype for the stored data */
#define BUFF_DATATYPE uint8_t // Change to the data type that is going to be stored into the buffer
/* Peek routine - uncomment to include the peek routine (fetches next byte without removing it from the buffer */
#define BUFF_USEPEEK
#ifndef _RINGBUFF_H_
#define _RINGBUFF_H_
/* Includes: */
#include <avr/io.h>
#include <avr/interrupt.h>
#include <util/atomic.h>
#include <limits.h>
#include <LUFA/Common/Common.h>
/* Defines and checks: */
#if defined(BUFF_STATICSIZE)
#define BUFF_LENGTH BUFF_STATICSIZE
#else
#error No buffer length specified!
#endif
#if !(defined(BUFF_DROPOLD) || defined(BUFF_DROPNEW) || defined(BUFF_NODROPCHECK))
#error No buffer drop mode specified.
#endif
#if !defined(BUFF_DATATYPE)
#error Ringbuffer storage data type not specified.
#endif
#if defined(BUFF_VOLATILE)
#define BUFF_MODE volatile
#define BUFF_ATOMIC_BLOCK ATOMIC_BLOCK(ATOMIC_RESTORESTATE)
#else
#define BUFF_MODE
#define BUFF_ATOMIC_BLOCK
#endif
#if (BUFF_STATICSIZE > LONG_MAX)
#define RingBuff_Elements_t uint64_t
#elif (BUFF_STATICSIZE > INT_MAX)
#define RingBuff_Elements_t uint32_t
#elif (BUFF_STATICSIZE > CHAR_MAX)
#define RingBuff_Elements_t uint16_t
#else
#define RingBuff_Elements_t uint8_t
#endif
/* Type Defines: */
typedef BUFF_DATATYPE RingBuff_Data_t;
typedef BUFF_MODE struct
{
RingBuff_Data_t Buffer[BUFF_LENGTH];
RingBuff_Data_t* InPtr;
RingBuff_Data_t* OutPtr;
RingBuff_Elements_t Elements;
} RingBuff_t;
/* Function Prototypes: */
void Buffer_Initialize(RingBuff_t* Buff);
void Buffer_StoreElement(RingBuff_t* Buffer, RingBuff_Data_t Data);
RingBuff_Data_t Buffer_GetElement(RingBuff_t* Buffer);
#if defined(BUFF_USEPEEK)
RingBuff_Data_t Buffer_PeekElement(const RingBuff_t* Buffer);
#endif
#endif

@ -0,0 +1,104 @@
ubuntu@ubuntu:~/LUFA/Bootloaders/LUFA_DFU_Bootloader_AT90USB162$ sudo avrdude -vv -F -P /dev/ttyACM0 -c avr910 -p usb162 -U flash:w:BootloaderDFU.hex
avrdude: Version 5.5, compiled on May 9 2008 at 13:04:46
Copyright (c) 2000-2005 Brian Dean, http://www.bdmicro.com/
System wide configuration file is "/etc/avrdude.conf"
User configuration file is "/home/ubuntu/.avrduderc"
User configuration file does not exist or is not a regular file, skipping
Using Port : /dev/ttyACM0
Using Programmer : avr910
AVR Part : AT90USB162
Chip Erase delay : 9000 us
PAGEL : PD7
BS2 : PA0
RESET disposition : dedicated
RETRY pulse : SCK
serial program mode : yes
parallel program mode : yes
Timeout : 200
StabDelay : 100
CmdexeDelay : 25
SyncLoops : 32
ByteDelay : 0
PollIndex : 3
PollValue : 0x53
Memory Detail :
Block Poll Page Polled
Memory Type Mode Delay Size Indx Paged Size Size #Pages MinW MaxW ReadBack
----------- ---- ----- ----- ---- ------ ------ ---- ------ ----- ----- ---------
eeprom 65 10 8 0 no 512 4 0 9000 9000 0x00 0x00
flash 65 6 128 0 yes 16384 128 128 4500 4500 0x00 0x00
lfuse 0 0 0 0 no 1 0 0 9000 9000 0x00 0x00
hfuse 0 0 0 0 no 1 0 0 9000 9000 0x00 0x00
efuse 0 0 0 0 no 1 0 0 9000 9000 0x00 0x00
lock 0 0 0 0 no 1 0 0 9000 9000 0x00 0x00
calibration 0 0 0 0 no 1 0 0 0 0 0x00 0x00
signature 0 0 0 0 no 3 0 0 0 0 0x00 0x00
Programmer Type : avr910
Description : Atmel Low Cost Serial Programmer
Found programmer: Id = "AVR ISP"; type = S
Software Version = 2.3; Hardware Version = 1.0
Programmer supports auto addr increment.
Programmer supports the following devices:
Device code: 0x55 = ATtiny12
Device code: 0x56 = ATtiny15
Device code: 0x5e = ATtiny2313
Device code: 0x76 = ATMEGA8
Device code: 0x74 = ATMEGA6450
Device code: 0x72 = ATMEGA32
Device code: 0x45 = ATMEGA64
Device code: 0x74 = ATMEGA6450
Device code: 0x43 = ATMEGA128
Device code: 0x63 = ATMEGA162
Device code: 0x78 = ATMEGA169
Device code: 0x6c = AT90S4434
Device code: 0x38 = AT90S8515
Device code: 0x65 = (unknown)
avrdude: warning: selected device is not supported by programmer: usb162
avrdude: AVR device initialized and ready to accept instructions
Reading | ################################################## | 100% 0.00s
avrdude: Device signature = 0x1e9482
avrdude: safemode: lfuse reads as 5E
avrdude: safemode: hfuse reads as D9
avrdude: safemode: efuse reads as F4
avrdude: NOTE: FLASH memory has been specified, an erase cycle will be performed
To disable this feature, specify the -D option.
avrdude: erasing chip
avrdude: reading input file "BootloaderDFU.hex"
avrdude: input file BootloaderDFU.hex auto detected as Intel Hex
avrdude: writing flash (16066 bytes):
Writing | ################################################## | 100% 33.39s
avrdude: 16066 bytes of flash written
avrdude: verifying flash memory against BootloaderDFU.hex:
avrdude: load data flash data from input file BootloaderDFU.hex:
avrdude: input file BootloaderDFU.hex auto detected as Intel Hex
avrdude: input file BootloaderDFU.hex contains 16066 bytes
avrdude: reading on-chip flash data:
Reading | ################################################## | 100% 16.07s
avrdude: verifying ...
avrdude: 16066 bytes of flash verified
avrdude: safemode: lfuse reads as 5E
avrdude: safemode: hfuse reads as D9
avrdude: safemode: efuse reads as F4
avrdude: safemode: Fuses OK
avrdude done. Thank you.

@ -0,0 +1,704 @@
# Hey Emacs, this is a -*- makefile -*-
#----------------------------------------------------------------------------
# WinAVR Makefile Template written by Eric B. Weddington, Jörg Wunsch, et al.
# >> Modified for use with the LUFA project. <<
#
# Released to the Public Domain
#
# Additional material for this makefile was written by:
# Peter Fleury
# Tim Henigan
# Colin O'Flynn
# Reiner Patommel
# Markus Pfaff
# Sander Pool
# Frederik Rouleau
# Carlos Lamas
# Dean Camera
# Opendous Inc.
# Denver Gingerich
#
#----------------------------------------------------------------------------
# On command line:
#
# make all = Make software.
#
# make clean = Clean out built project files.
#
# make coff = Convert ELF to AVR COFF.
#
# make extcoff = Convert ELF to AVR Extended COFF.
#
# make program = Download the hex file to the device, using avrdude.
# Please customize the avrdude settings below first!
#
# make dfu = Download the hex file to the device, using dfu-programmer (must
# have dfu-programmer installed).
#
# make flip = Download the hex file to the device, using Atmel FLIP (must
# have Atmel FLIP installed).
#
# make dfu-ee = Download the eeprom file to the device, using dfu-programmer
# (must have dfu-programmer installed).
#
# make flip-ee = Download the eeprom file to the device, using Atmel FLIP
# (must have Atmel FLIP installed).
#
# make doxygen = Generate DoxyGen documentation for the project (must have
# DoxyGen installed)
#
# make debug = Start either simulavr or avarice as specified for debugging,
# with avr-gdb or avr-insight as the front end for debugging.
#
# make filename.s = Just compile filename.c into the assembler code only.
#
# make filename.i = Create a preprocessed source file for use in submitting
# bug reports to the GCC project.
#
# To rebuild project do "make clean" then "make all".
#----------------------------------------------------------------------------
# MCU name
MCU = at90usb1287
# Target board (USBKEY, STK525, STK526, RZUSBSTICK, USER or blank for projects not requiring
# LUFA board drivers). If USER is selected, put custom board drivers in a directory called
# "Board" inside the application directory.
BOARD = USBKEY
# Processor frequency.
# This will define a symbol, F_CPU, in all source code files equal to the
# processor frequency. You can then use this symbol in your source code to
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
# automatically to create a 32-bit value in your source code.
# Typical values are:
# F_CPU = 1000000
# F_CPU = 1843200
# F_CPU = 2000000
# F_CPU = 3686400
# F_CPU = 4000000
# F_CPU = 7372800
# F_CPU = 8000000
# F_CPU = 11059200
# F_CPU = 14745600
# F_CPU = 16000000
# F_CPU = 18432000
# F_CPU = 20000000
F_CPU = 8000000
# Output format. (can be srec, ihex, binary)
FORMAT = ihex
# Target file name (without extension).
TARGET = AVRISP_Programmer
# Object files directory
# To put object files in current directory, use a dot (.), do NOT make
# this an empty or blank macro!
OBJDIR = .
# List C source files here. (C dependencies are automatically generated.)
SRC = $(TARGET).c \
Descriptors.c \
RingBuff.c \
../../LUFA/Scheduler/Scheduler.c \
../../LUFA/Drivers/AT90USBXXX/Serial.c \
../../LUFA/Drivers/USB/LowLevel/LowLevel.c \
../../LUFA/Drivers/USB/LowLevel/Endpoint.c \
../../LUFA/Drivers/USB/LowLevel/DevChapter9.c \
../../LUFA/Drivers/USB/HighLevel/USBTask.c \
../../LUFA/Drivers/USB/HighLevel/USBInterrupt.c \
../../LUFA/Drivers/USB/HighLevel/Events.c \
../../LUFA/Drivers/USB/HighLevel/StdDescriptors.c \
# List C++ source files here. (C dependencies are automatically generated.)
CPPSRC =
# List Assembler source files here.
# Make them always end in a capital .S. Files ending in a lowercase .s
# will not be considered source files but generated files (assembler
# output from the compiler), and will be deleted upon "make clean"!
# Even though the DOS/Win* filesystem matches both .s and .S the same,
# it will preserve the spelling of the filenames, and gcc itself does
# care about how the name is spelled on its command-line.
ASRC =
# Optimization level, can be [0, 1, 2, 3, s].
# 0 = turn off optimization. s = optimize for size.
# (Note: 3 is not always the best optimization level. See avr-libc FAQ.)
OPT = s
# Debugging format.
# Native formats for AVR-GCC's -g are dwarf-2 [default] or stabs.
# AVR Studio 4.10 requires dwarf-2.
# AVR [Extended] COFF format requires stabs, plus an avr-objcopy run.
DEBUG = dwarf-2
# List any extra directories to look for include files here.
# Each directory must be seperated by a space.
# Use forward slashes for directory separators.
# For a directory that has spaces, enclose it in quotes.
EXTRAINCDIRS = ../../
# Compiler flag to set the C Standard level.
# c89 = "ANSI" C
# gnu89 = c89 plus GCC extensions
# c99 = ISO C99 standard (not yet fully implemented)
# gnu99 = c99 plus GCC extensions
CSTANDARD = -std=gnu99
# Place -D or -U options here for C sources
CDEFS = -DF_CPU=$(F_CPU)UL -DBOARD=BOARD_$(BOARD) -DUSE_NONSTANDARD_DESCRIPTOR_NAMES -DNO_STREAM_CALLBACKS
CDEFS += -DUSB_DEVICE_ONLY -DUSE_STATIC_OPTIONS="(USB_DEVICE_OPT_FULLSPEED | USB_OPT_REG_ENABLED | USB_OPT_AUTO_PLL)"
# Place -D or -U options here for ASM sources
ADEFS = -DF_CPU=$(F_CPU)
# Place -D or -U options here for C++ sources
CPPDEFS = -DF_CPU=$(F_CPU)UL
#CPPDEFS += -D__STDC_LIMIT_MACROS
#CPPDEFS += -D__STDC_CONSTANT_MACROS
#---------------- Compiler Options C ----------------
# -g*: generate debugging information
# -O*: optimization level
# -f...: tuning, see GCC manual and avr-libc documentation
# -Wall...: warning level
# -Wa,...: tell GCC to pass this to the assembler.
# -adhlns...: create assembler listing
CFLAGS = -g$(DEBUG)
CFLAGS += $(CDEFS)
CFLAGS += -O$(OPT)
CFLAGS += -funsigned-char
CFLAGS += -funsigned-bitfields
CFLAGS += -ffunction-sections
CFLAGS += -fpack-struct
CFLAGS += -fshort-enums
CFLAGS += -finline-limit=20
CFLAGS += -Wall
CFLAGS += -Wstrict-prototypes
CFLAGS += -Wundef
#CFLAGS += -fno-unit-at-a-time
#CFLAGS += -Wunreachable-code
#CFLAGS += -Wsign-compare
CFLAGS += -Wa,-adhlns=$(<:%.c=$(OBJDIR)/%.lst)
CFLAGS += $(patsubst %,-I%,$(EXTRAINCDIRS))
CFLAGS += $(CSTANDARD)
#---------------- Compiler Options C++ ----------------
# -g*: generate debugging information
# -O*: optimization level
# -f...: tuning, see GCC manual and avr-libc documentation
# -Wall...: warning level
# -Wa,...: tell GCC to pass this to the assembler.
# -adhlns...: create assembler listing
CPPFLAGS = -g$(DEBUG)
CPPFLAGS += $(CPPDEFS)
CPPFLAGS += -O$(OPT)
CPPFLAGS += -funsigned-char
CPPFLAGS += -funsigned-bitfields
CPPFLAGS += -fpack-struct
CPPFLAGS += -fshort-enums
CPPFLAGS += -fno-exceptions
CPPFLAGS += -Wall
CFLAGS += -Wundef
#CPPFLAGS += -mshort-calls
#CPPFLAGS += -fno-unit-at-a-time
#CPPFLAGS += -Wstrict-prototypes
#CPPFLAGS += -Wunreachable-code
#CPPFLAGS += -Wsign-compare
CPPFLAGS += -Wa,-adhlns=$(<:%.cpp=$(OBJDIR)/%.lst)
CPPFLAGS += $(patsubst %,-I%,$(EXTRAINCDIRS))
#CPPFLAGS += $(CSTANDARD)
#---------------- Assembler Options ----------------
# -Wa,...: tell GCC to pass this to the assembler.
# -adhlns: create listing
# -gstabs: have the assembler create line number information; note that
# for use in COFF files, additional information about filenames
# and function names needs to be present in the assembler source
# files -- see avr-libc docs [FIXME: not yet described there]
# -listing-cont-lines: Sets the maximum number of continuation lines of hex
# dump that will be displayed for a given single line of source input.
ASFLAGS = $(ADEFS) -Wa,-adhlns=$(<:%.S=$(OBJDIR)/%.lst),-gstabs,--listing-cont-lines=100
#---------------- Library Options ----------------
# Minimalistic printf version
PRINTF_LIB_MIN = -Wl,-u,vfprintf -lprintf_min
# Floating point printf version (requires MATH_LIB = -lm below)
PRINTF_LIB_FLOAT = -Wl,-u,vfprintf -lprintf_flt
# If this is left blank, then it will use the Standard printf version.
PRINTF_LIB =
#PRINTF_LIB = $(PRINTF_LIB_MIN)
#PRINTF_LIB = $(PRINTF_LIB_FLOAT)
# Minimalistic scanf version
SCANF_LIB_MIN = -Wl,-u,vfscanf -lscanf_min
# Floating point + %[ scanf version (requires MATH_LIB = -lm below)
SCANF_LIB_FLOAT = -Wl,-u,vfscanf -lscanf_flt
# If this is left blank, then it will use the Standard scanf version.
SCANF_LIB =
#SCANF_LIB = $(SCANF_LIB_MIN)
#SCANF_LIB = $(SCANF_LIB_FLOAT)
MATH_LIB = -lm
# List any extra directories to look for libraries here.
# Each directory must be seperated by a space.
# Use forward slashes for directory separators.
# For a directory that has spaces, enclose it in quotes.
EXTRALIBDIRS =
#---------------- External Memory Options ----------------
# 64 KB of external RAM, starting after internal RAM (ATmega128!),
# used for variables (.data/.bss) and heap (malloc()).
#EXTMEMOPTS = -Wl,-Tdata=0x801100,--defsym=__heap_end=0x80ffff
# 64 KB of external RAM, starting after internal RAM (ATmega128!),
# only used for heap (malloc()).
#EXTMEMOPTS = -Wl,--section-start,.data=0x801100,--defsym=__heap_end=0x80ffff
EXTMEMOPTS =
#---------------- Linker Options ----------------
# -Wl,...: tell GCC to pass this to linker.
# -Map: create map file
# --cref: add cross reference to map file
LDFLAGS = -Wl,-Map=$(TARGET).map,--cref
LDFLAGS += -Wl,--relax
LDFLAGS += -Wl,--gc-sections
LDFLAGS += $(EXTMEMOPTS)
LDFLAGS += $(patsubst %,-L%,$(EXTRALIBDIRS))
LDFLAGS += $(PRINTF_LIB) $(SCANF_LIB) $(MATH_LIB)
#LDFLAGS += -T linker_script.x
#---------------- Programming Options (avrdude) ----------------
# Programming hardware: alf avr910 avrisp bascom bsd
# dt006 pavr picoweb pony-stk200 sp12 stk200 stk500
#
# Type: avrdude -c ?
# to get a full listing.
#
AVRDUDE_PROGRAMMER = jtagmkII
# com1 = serial port. Use lpt1 to connect to parallel port.
AVRDUDE_PORT = usb
AVRDUDE_WRITE_FLASH = -U flash:w:$(TARGET).hex
#AVRDUDE_WRITE_EEPROM = -U eeprom:w:$(TARGET).eep
# Uncomment the following if you want avrdude's erase cycle counter.
# Note that this counter needs to be initialized first using -Yn,
# see avrdude manual.
#AVRDUDE_ERASE_COUNTER = -y
# Uncomment the following if you do /not/ wish a verification to be
# performed after programming the device.
#AVRDUDE_NO_VERIFY = -V
# Increase verbosity level. Please use this when submitting bug
# reports about avrdude. See <http://savannah.nongnu.org/projects/avrdude>
# to submit bug reports.
#AVRDUDE_VERBOSE = -v -v
AVRDUDE_FLAGS = -p $(MCU) -P $(AVRDUDE_PORT) -c $(AVRDUDE_PROGRAMMER)
AVRDUDE_FLAGS += $(AVRDUDE_NO_VERIFY)
AVRDUDE_FLAGS += $(AVRDUDE_VERBOSE)
AVRDUDE_FLAGS += $(AVRDUDE_ERASE_COUNTER)
#---------------- Debugging Options ----------------
# For simulavr only - target MCU frequency.
DEBUG_MFREQ = $(F_CPU)
# Set the DEBUG_UI to either gdb or insight.
# DEBUG_UI = gdb
DEBUG_UI = insight
# Set the debugging back-end to either avarice, simulavr.
DEBUG_BACKEND = avarice
#DEBUG_BACKEND = simulavr
# GDB Init Filename.
GDBINIT_FILE = __avr_gdbinit
# When using avarice settings for the JTAG
JTAG_DEV = /dev/com1
# Debugging port used to communicate between GDB / avarice / simulavr.
DEBUG_PORT = 4242
# Debugging host used to communicate between GDB / avarice / simulavr, normally
# just set to localhost unless doing some sort of crazy debugging when
# avarice is running on a different computer.
DEBUG_HOST = localhost
#============================================================================
# Define programs and commands.
SHELL = sh
CC = avr-gcc
OBJCOPY = avr-objcopy
OBJDUMP = avr-objdump
SIZE = avr-size
AR = avr-ar rcs
NM = avr-nm
AVRDUDE = avrdude
REMOVE = rm -f
REMOVEDIR = rm -rf
COPY = cp
WINSHELL = cmd
# Define Messages
# English
MSG_ERRORS_NONE = Errors: none
MSG_BEGIN = -------- begin --------
MSG_END = -------- end --------
MSG_SIZE_BEFORE = Size before:
MSG_SIZE_AFTER = Size after:
MSG_COFF = Converting to AVR COFF:
MSG_EXTENDED_COFF = Converting to AVR Extended COFF:
MSG_FLASH = Creating load file for Flash:
MSG_EEPROM = Creating load file for EEPROM:
MSG_EXTENDED_LISTING = Creating Extended Listing:
MSG_SYMBOL_TABLE = Creating Symbol Table:
MSG_LINKING = Linking:
MSG_COMPILING = Compiling C:
MSG_COMPILING_CPP = Compiling C++:
MSG_ASSEMBLING = Assembling:
MSG_CLEANING = Cleaning project:
MSG_CREATING_LIBRARY = Creating library:
# Define all object files.
OBJ = $(SRC:%.c=$(OBJDIR)/%.o) $(CPPSRC:%.cpp=$(OBJDIR)/%.o) $(ASRC:%.S=$(OBJDIR)/%.o)
# Define all listing files.
LST = $(SRC:%.c=$(OBJDIR)/%.lst) $(CPPSRC:%.cpp=$(OBJDIR)/%.lst) $(ASRC:%.S=$(OBJDIR)/%.lst)
# Compiler flags to generate dependency files.
GENDEPFLAGS = -MMD -MP -MF .dep/$(@F).d
# Combine all necessary flags and optional flags.
# Add target processor to flags.
ALL_CFLAGS = -mmcu=$(MCU) -I. $(CFLAGS) $(GENDEPFLAGS)
ALL_CPPFLAGS = -mmcu=$(MCU) -I. -x c++ $(CPPFLAGS) $(GENDEPFLAGS)
ALL_ASFLAGS = -mmcu=$(MCU) -I. -x assembler-with-cpp $(ASFLAGS)
# Default target.
all: begin gccversion sizebefore build checkhooks checklibmode sizeafter end
# Change the build target to build a HEX file or a library.
build: elf hex eep lss sym
#build: lib
elf: $(TARGET).elf
hex: $(TARGET).hex
eep: $(TARGET).eep
lss: $(TARGET).lss
sym: $(TARGET).sym
LIBNAME=lib$(TARGET).a
lib: $(LIBNAME)
# Eye candy.
# AVR Studio 3.x does not check make's exit code but relies on
# the following magic strings to be generated by the compile job.
begin:
@echo
@echo $(MSG_BEGIN)
end:
@echo $(MSG_END)
@echo
# Display size of file.
HEXSIZE = $(SIZE) --target=$(FORMAT) $(TARGET).hex
ELFSIZE = $(SIZE) $(MCU_FLAG) $(FORMAT_FLAG) $(TARGET).elf
MCU_FLAG = $(shell $(SIZE) --help | grep -- --mcu > /dev/null && echo --mcu=$(MCU) )
FORMAT_FLAG = $(shell $(SIZE) --help | grep -- --format=.*avr > /dev/null && echo --format=avr )
sizebefore:
@if test -f $(TARGET).elf; then echo; echo $(MSG_SIZE_BEFORE); $(ELFSIZE); \
2>/dev/null; echo; fi
sizeafter:
@if test -f $(TARGET).elf; then echo; echo $(MSG_SIZE_AFTER); $(ELFSIZE); \
2>/dev/null; echo; fi
checkhooks: build
@echo
@echo ------- Unhooked LUFA Events -------
@$(shell) (grep -s '^Event.*LUFA/.*\\.o' $(TARGET).map | \
cut -d' ' -f1 | cut -d'_' -f2- | grep ".*") || \
echo "(None)"
@echo ----- End Unhooked LUFA Events -----
checklibmode:
@echo
@echo ----------- Library Mode -----------
@$(shell) ($(CC) $(ALL_CFLAGS) -E -dM - < /dev/null \
| grep 'USB_\(DEVICE\|HOST\)_ONLY' | cut -d' ' -f2 | grep ".*") \
|| echo "No specific mode (both device and host mode allowable)."
@echo ------------------------------------
# Display compiler version information.
gccversion :
@$(CC) --version
# Program the device.
program: $(TARGET).hex $(TARGET).eep
$(AVRDUDE) $(AVRDUDE_FLAGS) $(AVRDUDE_WRITE_FLASH) $(AVRDUDE_WRITE_EEPROM)
flip: $(TARGET).hex
batchisp -hardware usb -device $(MCU) -operation erase f
batchisp -hardware usb -device $(MCU) -operation loadbuffer $(TARGET).hex program
batchisp -hardware usb -device $(MCU) -operation start reset 0
dfu: $(TARGET).hex
dfu-programmer $(MCU) erase
dfu-programmer $(MCU) flash --debug 1 $(TARGET).hex
dfu-programmer $(MCU) reset
flip-ee: $(TARGET).hex $(TARGET).eep
copy $(TARGET).eep $(TARGET)eep.hex
batchisp -hardware usb -device $(MCU) -operation memory EEPROM erase
batchisp -hardware usb -device $(MCU) -operation memory EEPROM loadbuffer $(TARGET)eep.hex program
batchisp -hardware usb -device $(MCU) -operation start reset 0
dfu-ee: $(TARGET).hex $(TARGET).eep
dfu-programmer $(MCU) erase
dfu-programmer $(MCU) eeprom --debug 1 $(TARGET).eep
dfu-programmer $(MCU) reset
# Generate avr-gdb config/init file which does the following:
# define the reset signal, load the target file, connect to target, and set
# a breakpoint at main().
gdb-config:
@$(REMOVE) $(GDBINIT_FILE)
@echo define reset >> $(GDBINIT_FILE)
@echo SIGNAL SIGHUP >> $(GDBINIT_FILE)
@echo end >> $(GDBINIT_FILE)
@echo file $(TARGET).elf >> $(GDBINIT_FILE)
@echo target remote $(DEBUG_HOST):$(DEBUG_PORT) >> $(GDBINIT_FILE)
ifeq ($(DEBUG_BACKEND),simulavr)
@echo load >> $(GDBINIT_FILE)
endif
@echo break main >> $(GDBINIT_FILE)
debug: gdb-config $(TARGET).elf
ifeq ($(DEBUG_BACKEND), avarice)
@echo Starting AVaRICE - Press enter when "waiting to connect" message displays.
@$(WINSHELL) /c start avarice --jtag $(JTAG_DEV) --erase --program --file \
$(TARGET).elf $(DEBUG_HOST):$(DEBUG_PORT)
@$(WINSHELL) /c pause
else
@$(WINSHELL) /c start simulavr --gdbserver --device $(MCU) --clock-freq \
$(DEBUG_MFREQ) --port $(DEBUG_PORT)
endif
@$(WINSHELL) /c start avr-$(DEBUG_UI) --command=$(GDBINIT_FILE)
# Convert ELF to COFF for use in debugging / simulating in AVR Studio or VMLAB.
COFFCONVERT = $(OBJCOPY) --debugging
COFFCONVERT += --change-section-address .data-0x800000
COFFCONVERT += --change-section-address .bss-0x800000
COFFCONVERT += --change-section-address .noinit-0x800000
COFFCONVERT += --change-section-address .eeprom-0x810000
coff: $(TARGET).elf
@echo
@echo $(MSG_COFF) $(TARGET).cof
$(COFFCONVERT) -O coff-avr $< $(TARGET).cof
extcoff: $(TARGET).elf
@echo
@echo $(MSG_EXTENDED_COFF) $(TARGET).cof
$(COFFCONVERT) -O coff-ext-avr $< $(TARGET).cof
# Create final output files (.hex, .eep) from ELF output file.
%.hex: %.elf
@echo
@echo $(MSG_FLASH) $@
$(OBJCOPY) -O $(FORMAT) -R .eeprom $< $@
%.eep: %.elf
@echo
@echo $(MSG_EEPROM) $@
-$(OBJCOPY) -j .eeprom --set-section-flags=.eeprom="alloc,load" \
--change-section-lma .eeprom=0 --no-change-warnings -O $(FORMAT) $< $@ || exit 0
# Create extended listing file from ELF output file.
%.lss: %.elf
@echo
@echo $(MSG_EXTENDED_LISTING) $@
$(OBJDUMP) -h -z -S $< > $@
# Create a symbol table from ELF output file.
%.sym: %.elf
@echo
@echo $(MSG_SYMBOL_TABLE) $@
$(NM) -n $< > $@
# Create library from object files.
.SECONDARY : $(TARGET).a
.PRECIOUS : $(OBJ)
%.a: $(OBJ)
@echo
@echo $(MSG_CREATING_LIBRARY) $@
$(AR) $@ $(OBJ)
# Link: create ELF output file from object files.
.SECONDARY : $(TARGET).elf
.PRECIOUS : $(OBJ)
%.elf: $(OBJ)
@echo
@echo $(MSG_LINKING) $@
$(CC) $(ALL_CFLAGS) $^ --output $@ $(LDFLAGS)
# Compile: create object files from C source files.
$(OBJDIR)/%.o : %.c
@echo
@echo $(MSG_COMPILING) $<
$(CC) -c $(ALL_CFLAGS) $< -o $@
# Compile: create object files from C++ source files.
$(OBJDIR)/%.o : %.cpp
@echo
@echo $(MSG_COMPILING_CPP) $<
$(CC) -c $(ALL_CPPFLAGS) $< -o $@
# Compile: create assembler files from C source files.
%.s : %.c
$(CC) -S $(ALL_CFLAGS) $< -o $@
# Compile: create assembler files from C++ source files.
%.s : %.cpp
$(CC) -S $(ALL_CPPFLAGS) $< -o $@
# Assemble: create object files from assembler source files.
$(OBJDIR)/%.o : %.S
@echo
@echo $(MSG_ASSEMBLING) $<
$(CC) -c $(ALL_ASFLAGS) $< -o $@
# Create preprocessed source for use in sending a bug report.
%.i : %.c
$(CC) -E -mmcu=$(MCU) -I. $(CFLAGS) $< -o $@
# Target: clean project.
clean: begin clean_list clean_binary end
clean_binary:
$(REMOVE) $(TARGET).hex
clean_list:
@echo $(MSG_CLEANING)
$(REMOVE) $(TARGET).eep
$(REMOVE) $(TARGET).cof
$(REMOVE) $(TARGET).elf
$(REMOVE) $(TARGET).map
$(REMOVE) $(TARGET).sym
$(REMOVE) $(TARGET).lss
$(REMOVE) $(SRC:%.c=$(OBJDIR)/%.o)
$(REMOVE) $(SRC:%.c=$(OBJDIR)/%.lst)
$(REMOVE) $(SRC:.c=.s)
$(REMOVE) $(SRC:.c=.d)
$(REMOVE) $(SRC:.c=.i)
$(REMOVEDIR) .dep
doxygen:
@echo Generating Project Documentation...
@doxygen Doxygen.conf
@echo Documentation Generation Complete.
clean_doxygen:
rm -rf Documentation
# Create object files directory
$(shell mkdir $(OBJDIR) 2>/dev/null)
# Include the dependency files.
-include $(shell mkdir .dep 2>/dev/null) $(wildcard .dep/*)
# Listing of phony targets.
.PHONY : all checkhooks checklibmode begin \
finish end sizebefore sizeafter gccversion \
build elf hex eep lss sym coff extcoff \
clean clean_list clean_binary program debug \
gdb-config doxygen dfu flip

@ -0,0 +1,113 @@
/*
LUFA Library
Copyright (C) Dean Camera, 2009.
dean [at] fourwalledcubicle [dot] com
www.fourwalledcubicle.com
*/
/*
Copyright 2009 Denver Gingerich (denver [at] ossguy [dot] com)
Copyright 2009 Dean Camera (dean [at] fourwalledcubicle [dot] com)
Permission to use, copy, modify, and distribute this software
and its documentation for any purpose and without fee is hereby
granted, provided that the above copyright notice appear in all
copies and that both that the copyright notice and this
permission notice and warranty disclaimer appear in supporting
documentation, and that the name of the author not be used in
advertising or publicity pertaining to distribution of the
software without specific, written prior permission.
The author disclaim all warranties with regard to this
software, including all implied warranties of merchantability
and fitness. In no event shall the author be liable for any
special, indirect or consequential damages or any damages
whatsoever resulting from loss of use, data or profits, whether
in an action of contract, negligence or other tortious action,
arising out of or in connection with the use or performance of
this software.
*/
/** Circular bit buffer library. This will allow for individual bits
* to be stored in packed form inside circular buffers, to reduce
* overall RAM usage.
*/
#include "CircularBitBuffer.h"
/** Function to initialize or reset a bit buffer, ready for data to be stored into it. */
void BitBuffer_Init(BitBuffer_t* Buffer)
{
/* Reset the number of stored bits in the buffer */
Buffer->Elements = 0;
/* Reset the data in and out pointer structures in the buffer to the first buffer bit */
Buffer->In.CurrentByte = Buffer->Data;
Buffer->In.ByteMask = (1 << 0);
Buffer->Out.CurrentByte = Buffer->Data;
Buffer->Out.ByteMask = (1 << 0);
}
/** Function to store the given bit into the given bit buffer. */
void BitBuffer_StoreNextBit(BitBuffer_t* Buffer, bool Bit)
{
/* If the bit to store is true, set the next bit in the buffer */
if (Bit)
*Buffer->In.CurrentByte |= Buffer->In.ByteMask;
/* Increment the number of stored bits in the buffer counter */
Buffer->Elements++;
/* Check if the current buffer byte is full of stored bits */
if (Buffer->In.ByteMask == (1 << 7))
{
/* Check if the end of the buffer has been reached, if so reset to start of buffer, otherwise advance to next bit */
if (Buffer->In.CurrentByte != &Buffer->Data[sizeof(Buffer->Data) - 1])
Buffer->In.CurrentByte++;
else
Buffer->In.CurrentByte = Buffer->Data;
/* Reset the storage bit mask in the current buffer byte to the first bit */
Buffer->In.ByteMask = (1 << 0);
}
else
{
/* Shift the current storage bit mask to the next bit in the current byte */
Buffer->In.ByteMask <<= 1;
}
}
/** Function to retrieve the next bit stored in the given bit buffer. */
bool BitBuffer_GetNextBit(BitBuffer_t* Buffer)
{
/* Retrieve the value of the next bit stored in the buffer */
bool Bit = ((*Buffer->Out.CurrentByte & Buffer->Out.ByteMask) != 0);
/* Clear the buffer bit */
*Buffer->Out.CurrentByte &= ~Buffer->Out.ByteMask;
/* Decrement the number of stored bits in the buffer counter */
Buffer->Elements--;
/* Check if the current buffer byte is empty of stored bits */
if (Buffer->Out.ByteMask == (1 << 7))
{
/* Check if the end of the buffer has been reached, if so reset to start of buffer, otherwise advance to next bit */
if (Buffer->Out.CurrentByte != &Buffer->Data[sizeof(Buffer->Data) - 1])
Buffer->Out.CurrentByte++;
else
Buffer->Out.CurrentByte = Buffer->Data;
/* Reset the retrieval bit mask in the current buffer byte to the first bit */
Buffer->Out.ByteMask = (1 << 0);
}
else
{
/* Shift the current retrieval bit mask to the next bit in the current byte */
Buffer->Out.ByteMask <<= 1;
}
/* Return the retrieved bit from the buffer */
return Bit;
}

@ -0,0 +1,95 @@
/*
LUFA Library
Copyright (C) Dean Camera, 2009.
dean [at] fourwalledcubicle [dot] com
www.fourwalledcubicle.com
*/
/*
Copyright 2009 Denver Gingerich (denver [at] ossguy [dot] com)
Copyright 2009 Dean Camera (dean [at] fourwalledcubicle [dot] com)
Permission to use, copy, modify, and distribute this software
and its documentation for any purpose and without fee is hereby
granted, provided that the above copyright notice appear in all
copies and that both that the copyright notice and this
permission notice and warranty disclaimer appear in supporting
documentation, and that the name of the author not be used in
advertising or publicity pertaining to distribution of the
software without specific, written prior permission.
The author disclaim all warranties with regard to this
software, including all implied warranties of merchantability
and fitness. In no event shall the author be liable for any
special, indirect or consequential damages or any damages
whatsoever resulting from loss of use, data or profits, whether
in an action of contract, negligence or other tortious action,
arising out of or in connection with the use or performance of
this software.
*/
/** \file
*
* Header file for CircularBitBuffer.c.
*/
#ifndef _CIRCULARBITBUFFER_H_
#define _CIRCULARBITBUFFER_H_
/* Includes: */
#include <avr/io.h>
#include <stdbool.h>
#include <LUFA/Common/Common.h>
/* Macros: */
#if (defined(__AVR_AT90USB1287__) || defined(__AVR_AT90USB647__) || \
defined(__AVR_AT90USB1286__) || defined(__AVR_AT90USB646__)) || defined(__DOXYGEN__)
/** Maximum number of bits which can be stored into a bit buffer. The memory usage is one eigth of this value per buffer. */
#define MAX_BITS 20480
#else
#define MAX_BITS 1024
#endif
/* Type Defines: */
/* Type define for a pointer to a bit in a bit buffer. */
typedef struct
{
uint8_t* CurrentByte; /**< Pointer to the current byte in the buffer */
uint8_t ByteMask; /**< Mask of the current bit in the buffer */
} BitBufferPointer_t;
/** Type define for a circular packet bit buffer. */
typedef struct
{
uint8_t Data[MAX_BITS / 8]; /**< Buffer to hold the stored bits in packed form */
uint16_t Elements; /**< Number of stored bits in the bit buffer */
BitBufferPointer_t In; /**< Bit pointer to the next storage location in the buffer */
BitBufferPointer_t Out; /**< Bit pointer to the next retrieval location in the buffer */
} BitBuffer_t;
/* Function Prototypes: */
/** Initializes or resets a given bit buffer, ready to store new bits.
*
* \param Buffer Bit buffer to initialize
*/
void BitBuffer_Init(BitBuffer_t* Buffer) ATTR_NON_NULL_PTR_ARG(1);
/** Stores a bit into the next location inside a given bit buffer.
*
* \param Buffer Bit buffer to store a bit into
* \param Bit Bit to store into the buffer
*/
void BitBuffer_StoreNextBit(BitBuffer_t* Buffer, bool Bit) ATTR_NON_NULL_PTR_ARG(1);
/** Retrieves a bit from the next location inside a given bit buffer.
*
* \param Buffer Bit buffer to store a bit into
*
* \return Next bit from the buffer
*/
bool BitBuffer_GetNextBit(BitBuffer_t* Buffer) ATTR_NON_NULL_PTR_ARG(1);
#endif

@ -0,0 +1,247 @@
/*
LUFA Library
Copyright (C) Dean Camera, 2009.
dean [at] fourwalledcubicle [dot] com
www.fourwalledcubicle.com
*/
/*
Copyright 2009 Denver Gingerich (denver [at] ossguy [dot] com)
Copyright 2009 Dean Camera (dean [at] fourwalledcubicle [dot] com)
Permission to use, copy, modify, and distribute this software
and its documentation for any purpose and without fee is hereby
granted, provided that the above copyright notice appear in all
copies and that both that the copyright notice and this
permission notice and warranty disclaimer appear in supporting
documentation, and that the name of the author not be used in
advertising or publicity pertaining to distribution of the
software without specific, written prior permission.
The author disclaim all warranties with regard to this
software, including all implied warranties of merchantability
and fitness. In no event shall the author be liable for any
special, indirect or consequential damages or any damages
whatsoever resulting from loss of use, data or profits, whether
in an action of contract, negligence or other tortious action,
arising out of or in connection with the use or performance of
this software.
*/
/** \file
*
* USB Device Descriptors, for library use when in USB device mode. Descriptors are special
* computer-readable structures which the host requests upon device enumeration, to determine
* the device's capabilities and functions.
*/
#include "Descriptors.h"
/** HID report descriptor. This is a HID class specific descriptor, which defines the structure of the
* reports sent and received by the HID device to and from the USB host. It indicates what data is sent,
* where in the report each element is located and exactly how the data should be interpreted and used.
*
* See the HID class specification for more information on HID report descriptors.
*/
USB_Descriptor_HIDReport_Datatype_t PROGMEM KeyboardReport[] =
{
0x05, 0x01, /* Usage Page (Generic Desktop) */
0x09, 0x06, /* Usage (Keyboard) */
0xa1, 0x01, /* Collection (Application) */
0x05, 0x07, /* Usage Page (Key Codes) */
0x19, 0xe0, /* Usage Minimum (Keyboard LeftControl) */
0x29, 0xe7, /* Usage Maximum (Keyboard Right GUI) */
0x15, 0x00, /* Logical Minimum (0) */
0x25, 0x01, /* Logical Maximum (1) */
0x75, 0x01, /* Report Size (1) */
0x95, 0x08, /* Report Count (8) */
0x81, 0x02, /* Input (Data, Variable, Absolute) */
0x95, 0x01, /* Report Count (1) */
0x75, 0x08, /* Report Size (8) */
0x81, 0x03, /* Input (Const, Variable, Absolute) */
0x95, 0x01, /* Report Count (1) */
0x75, 0x08, /* Report Size (8) */
0x15, 0x00, /* Logical Minimum (0) */
0x25, 0x65, /* Logical Maximum (101) */
0x05, 0x07, /* Usage Page (Keyboard) */
0x19, 0x00, /* Usage Minimum (Reserved (no event indicated)) */
0x29, 0x65, /* Usage Maximum (Keyboard Application) */
0x81, 0x00, /* Input (Data, Array, Absolute) */
0xc0 /* End Collection */
};
/** Device descriptor structure. This descriptor, located in FLASH memory, describes the overall
* device characteristics, including the supported USB version, control endpoint size and the
* number of device configurations. The descriptor is read out by the USB host when the enumeration
* process begins.
*/
USB_Descriptor_Device_t PROGMEM DeviceDescriptor =
{
Header: {Size: sizeof(USB_Descriptor_Device_t), Type: DTYPE_Device},
USBSpecification: VERSION_BCD(01.10),
Class: 0x00,
SubClass: 0x00,
Protocol: 0x00,
Endpoint0Size: 8,
VendorID: 0x03EB,
ProductID: 0x2042,
ReleaseNumber: 0x0000,
ManufacturerStrIndex: 0x01,
ProductStrIndex: 0x02,
SerialNumStrIndex: NO_DESCRIPTOR,
NumberOfConfigurations: 1
};
/** Configuration descriptor structure. This descriptor, located in FLASH memory, describes the usage
* of the device in one of its supported configurations, including information about any device interfaces
* and endpoints. The descriptor is read out by the USB host during the enumeration process when selecting
* a configuration so that the host may correctly communicate with the USB device.
*/
USB_Descriptor_Configuration_t PROGMEM ConfigurationDescriptor =
{
Config:
{
Header: {Size: sizeof(USB_Descriptor_Configuration_Header_t), Type: DTYPE_Configuration},
TotalConfigurationSize: sizeof(USB_Descriptor_Configuration_t),
TotalInterfaces: 1,
ConfigurationNumber: 1,
ConfigurationStrIndex: NO_DESCRIPTOR,
ConfigAttributes: (USB_CONFIG_ATTR_BUSPOWERED | USB_CONFIG_ATTR_SELFPOWERED),
MaxPowerConsumption: USB_CONFIG_POWER_MA(100)
},
Interface:
{
Header: {Size: sizeof(USB_Descriptor_Interface_t), Type: DTYPE_Interface},
InterfaceNumber: 0x00,
AlternateSetting: 0x00,
TotalEndpoints: 1,
Class: 0x03,
SubClass: 0x01,
Protocol: 0x01,
InterfaceStrIndex: NO_DESCRIPTOR
},
KeyboardHID:
{
Header: {Size: sizeof(USB_Descriptor_HID_t), Type: DTYPE_HID},
HIDSpec: VERSION_BCD(01.11),
CountryCode: 0x00,
TotalHIDReports: 0x01,
HIDReportType: DTYPE_Report,
HIDReportLength: sizeof(KeyboardReport)
},
KeyboardEndpoint:
{
Header: {Size: sizeof(USB_Descriptor_Endpoint_t), Type: DTYPE_Endpoint},
EndpointAddress: (ENDPOINT_DESCRIPTOR_DIR_IN | KEYBOARD_EPNUM),
Attributes: EP_TYPE_INTERRUPT,
EndpointSize: KEYBOARD_EPSIZE,
PollingIntervalMS: 0x02
},
};
/** Language descriptor structure. This descriptor, located in FLASH memory, is returned when the host requests
* the string descriptor with index 0 (the first index). It is actually an array of 16-bit integers, which indicate
* via the language ID table available at USB.org what languages the device supports for its string descriptors. */
USB_Descriptor_String_t PROGMEM LanguageString =
{
Header: {Size: USB_STRING_LEN(1), Type: DTYPE_String},
UnicodeString: {LANGUAGE_ID_ENG}
};
/** Manufacturer descriptor string. This is a Unicode string containing the manufacturer's details in human readable
* form, and is read out upon request by the host when the appropriate string ID is requested, listed in the Device
* Descriptor.
*/
USB_Descriptor_String_t PROGMEM ManufacturerString =
{
Header: {Size: USB_STRING_LEN(32), Type: DTYPE_String},
UnicodeString: L"Dean Camera and Denver Gingerich"
};
/** Product descriptor string. This is a Unicode string containing the product's details in human readable form,
* and is read out upon request by the host when the appropriate string ID is requested, listed in the Device
* Descriptor.
*/
USB_Descriptor_String_t PROGMEM ProductString =
{
Header: {Size: USB_STRING_LEN(20), Type: DTYPE_String},
UnicodeString: L"Magnetic Card Reader"
};
/** This function is called by the library when in device mode, and must be overridden (see StdDescriptors.h
* documentation) by the application code so that the address and size of a requested descriptor can be given
* to the USB library. When the device recieves a Get Descriptor request on the control endpoint, this function
* is called so that the descriptor details can be passed back and the appropriate descriptor sent back to the
* USB host.
*/
uint16_t USB_GetDescriptor(const uint16_t wValue, const uint8_t wIndex, void** const DescriptorAddress)
{
const uint8_t DescriptorType = (wValue >> 8);
const uint8_t DescriptorNumber = (wValue & 0xFF);
void* Address = NULL;
uint16_t Size = NO_DESCRIPTOR;
switch (DescriptorType)
{
case DTYPE_Device:
Address = DESCRIPTOR_ADDRESS(DeviceDescriptor);
Size = sizeof(USB_Descriptor_Device_t);
break;
case DTYPE_Configuration:
Address = DESCRIPTOR_ADDRESS(ConfigurationDescriptor);
Size = sizeof(USB_Descriptor_Configuration_t);
break;
case DTYPE_String:
switch (DescriptorNumber)
{
case 0x00:
Address = DESCRIPTOR_ADDRESS(LanguageString);
Size = pgm_read_byte(&LanguageString.Header.Size);
break;
case 0x01:
Address = DESCRIPTOR_ADDRESS(ManufacturerString);
Size = pgm_read_byte(&ManufacturerString.Header.Size);
break;
case 0x02:
Address = DESCRIPTOR_ADDRESS(ProductString);
Size = pgm_read_byte(&ProductString.Header.Size);
break;
}
break;
case DTYPE_HID:
Address = DESCRIPTOR_ADDRESS(ConfigurationDescriptor.KeyboardHID);
Size = sizeof(USB_Descriptor_HID_t);
break;
case DTYPE_Report:
Address = DESCRIPTOR_ADDRESS(KeyboardReport);
Size = sizeof(KeyboardReport);
break;
}
*DescriptorAddress = Address;
return Size;
}

@ -0,0 +1,98 @@
/*
LUFA Library
Copyright (C) Dean Camera, 2009.
dean [at] fourwalledcubicle [dot] com
www.fourwalledcubicle.com
*/
/*
Copyright 2009 Denver Gingerich (denver [at] ossguy [dot] com)
Copyright 2009 Dean Camera (dean [at] fourwalledcubicle [dot] com)
Permission to use, copy, modify, and distribute this software
and its documentation for any purpose and without fee is hereby
granted, provided that the above copyright notice appear in all
copies and that both that the copyright notice and this
permission notice and warranty disclaimer appear in supporting
documentation, and that the name of the author not be used in
advertising or publicity pertaining to distribution of the
software without specific, written prior permission.
The author disclaim all warranties with regard to this
software, including all implied warranties of merchantability
and fitness. In no event shall the author be liable for any
special, indirect or consequential damages or any damages
whatsoever resulting from loss of use, data or profits, whether
in an action of contract, negligence or other tortious action,
arising out of or in connection with the use or performance of
this software.
*/
/** \file
*
* Header file for Descriptors.c.
*/
#ifndef _DESCRIPTORS_H_
#define _DESCRIPTORS_H_
/* Includes: */
#include <LUFA/Drivers/USB/USB.h>
#include <avr/pgmspace.h>
/* Type Defines: */
/** Type define for the HID class specific HID descriptor. A HID descriptor is used in HID class devices
* to give information about the HID device, including the HID specification used, and the report descriptors
* the device contains to describe how the HID device should be controlled.
*/
typedef struct
{
USB_Descriptor_Header_t Header; /**< Standard USB descriptor header */
uint16_t HIDSpec; /**< HID specification implemented by the device, in BCD form */
uint8_t CountryCode; /**< Country code for the country the HID device is localised for */
uint8_t TotalHIDReports; /**< Total number of HID reports linked to this HID interface */
uint8_t HIDReportType; /**< Type of the first HID report descriptor */
uint16_t HIDReportLength; /**< Length of the first HID report descriptor */
} USB_Descriptor_HID_t;
/** Type define for the data type used for the HID Report descriptor data elements. A HID report
* descriptor contains an array of this data type, indicating how the reports from and to the
* device are formatted and how the report data is to be used by the host.
*/
typedef uint8_t USB_Descriptor_HIDReport_Datatype_t;
/** Type define for the device configuration descriptor structure. This must be defined in the
* application code, as the configuration descriptor contains several sub-descriptors which
* vary between devices, and which describe the device's usage to the host.
*/
typedef struct
{
USB_Descriptor_Configuration_Header_t Config; /**< Configuration descriptor header structure */
USB_Descriptor_Interface_t Interface; /**< Keyboard interface descriptor */
USB_Descriptor_HID_t KeyboardHID; /**< Keyboard HID descriptor */
USB_Descriptor_Endpoint_t KeyboardEndpoint; /**< Keyboard key report endpoint descriptor */
} USB_Descriptor_Configuration_t;
/* Macros: */
/** Endpoint number of the keyboard key press reporting endpoint. */
#define KEYBOARD_EPNUM 1
/** Size of the keyboard report endpoints, in bytes. */
#define KEYBOARD_EPSIZE 8
/** Descriptor type value for a HID descriptor. */
#define DTYPE_HID 0x21
/** Descriptor type value for a HID report. */
#define DTYPE_Report 0x22
/* Function Prototypes: */
uint16_t USB_GetDescriptor(const uint16_t wValue, const uint8_t wIndex, void** const DescriptorAddress)
ATTR_WARN_UNUSED_RESULT ATTR_NON_NULL_PTR_ARG(3);
#endif

@ -0,0 +1,1485 @@
# Doxyfile 1.5.7.1
# This file describes the settings to be used by the documentation system
# doxygen (www.doxygen.org) for a project
#
# All text after a hash (#) is considered a comment and will be ignored
# The format is:
# TAG = value [value, ...]
# For lists items can also be appended using:
# TAG += value [value, ...]
# Values that contain spaces should be placed between quotes (" ")
#---------------------------------------------------------------------------
# Project related configuration options
#---------------------------------------------------------------------------
# This tag specifies the encoding used for all characters in the config file
# that follow. The default is UTF-8 which is also the encoding used for all
# text before the first occurrence of this tag. Doxygen uses libiconv (or the
# iconv built into libc) for the transcoding. See
# http://www.gnu.org/software/libiconv for the list of possible encodings.
DOXYFILE_ENCODING = UTF-8
# The PROJECT_NAME tag is a single word (or a sequence of words surrounded
# by quotes) that should identify the project.
PROJECT_NAME = "Denver Gingerich's Stripe Snoop Project"
# The PROJECT_NUMBER tag can be used to enter a project or revision number.
# This could be handy for archiving the generated documentation or
# if some version control system is used.
PROJECT_NUMBER = 0.0.0
# The OUTPUT_DIRECTORY tag is used to specify the (relative or absolute)
# base path where the generated documentation will be put.
# If a relative path is entered, it will be relative to the location
# where doxygen was started. If left blank the current directory will be used.
OUTPUT_DIRECTORY = ./Documentation/
# If the CREATE_SUBDIRS tag is set to YES, then doxygen will create
# 4096 sub-directories (in 2 levels) under the output directory of each output
# format and will distribute the generated files over these directories.
# Enabling this option can be useful when feeding doxygen a huge amount of
# source files, where putting all generated files in the same directory would
# otherwise cause performance problems for the file system.
CREATE_SUBDIRS = YES
# The OUTPUT_LANGUAGE tag is used to specify the language in which all
# documentation generated by doxygen is written. Doxygen will use this
# information to generate all constant output in the proper language.
# The default language is English, other supported languages are:
# Afrikaans, Arabic, Brazilian, Catalan, Chinese, Chinese-Traditional,
# Croatian, Czech, Danish, Dutch, Farsi, Finnish, French, German, Greek,
# Hungarian, Italian, Japanese, Japanese-en (Japanese with English messages),
# Korean, Korean-en, Lithuanian, Norwegian, Macedonian, Persian, Polish,
# Portuguese, Romanian, Russian, Serbian, Serbian-Cyrilic, Slovak, Slovene,
# Spanish, Swedish, and Ukrainian.
OUTPUT_LANGUAGE = English
# If the BRIEF_MEMBER_DESC tag is set to YES (the default) Doxygen will
# include brief member descriptions after the members that are listed in
# the file and class documentation (similar to JavaDoc).
# Set to NO to disable this.
BRIEF_MEMBER_DESC = YES
# If the REPEAT_BRIEF tag is set to YES (the default) Doxygen will prepend
# the brief description of a member or function before the detailed description.
# Note: if both HIDE_UNDOC_MEMBERS and BRIEF_MEMBER_DESC are set to NO, the
# brief descriptions will be completely suppressed.
REPEAT_BRIEF = YES
# This tag implements a quasi-intelligent brief description abbreviator
# that is used to form the text in various listings. Each string
# in this list, if found as the leading text of the brief description, will be
# stripped from the text and the result after processing the whole list, is
# used as the annotated text. Otherwise, the brief description is used as-is.
# If left blank, the following values are used ("$name" is automatically
# replaced with the name of the entity): "The $name class" "The $name widget"
# "The $name file" "is" "provides" "specifies" "contains"
# "represents" "a" "an" "the"
ABBREVIATE_BRIEF = "The $name class" \
"The $name widget" \
"The $name file" \
is \
provides \
specifies \
contains \
represents \
a \
an \
the
# If the ALWAYS_DETAILED_SEC and REPEAT_BRIEF tags are both set to YES then
# Doxygen will generate a detailed section even if there is only a brief
# description.
ALWAYS_DETAILED_SEC = NO
# If the INLINE_INHERITED_MEMB tag is set to YES, doxygen will show all
# inherited members of a class in the documentation of that class as if those
# members were ordinary class members. Constructors, destructors and assignment
# operators of the base classes will not be shown.
INLINE_INHERITED_MEMB = NO
# If the FULL_PATH_NAMES tag is set to YES then Doxygen will prepend the full
# path before files name in the file list and in the header files. If set
# to NO the shortest path that makes the file name unique will be used.
FULL_PATH_NAMES = YES
# If the FULL_PATH_NAMES tag is set to YES then the STRIP_FROM_PATH tag
# can be used to strip a user-defined part of the path. Stripping is
# only done if one of the specified strings matches the left-hand part of
# the path. The tag can be used to show relative paths in the file list.
# If left blank the directory from which doxygen is run is used as the
# path to strip.
STRIP_FROM_PATH =
# The STRIP_FROM_INC_PATH tag can be used to strip a user-defined part of
# the path mentioned in the documentation of a class, which tells
# the reader which header file to include in order to use a class.
# If left blank only the name of the header file containing the class
# definition is used. Otherwise one should specify the include paths that
# are normally passed to the compiler using the -I flag.
STRIP_FROM_INC_PATH =
# If the SHORT_NAMES tag is set to YES, doxygen will generate much shorter
# (but less readable) file names. This can be useful is your file systems
# doesn't support long names like on DOS, Mac, or CD-ROM.
SHORT_NAMES = YES
# If the JAVADOC_AUTOBRIEF tag is set to YES then Doxygen
# will interpret the first line (until the first dot) of a JavaDoc-style
# comment as the brief description. If set to NO, the JavaDoc
# comments will behave just like regular Qt-style comments
# (thus requiring an explicit @brief command for a brief description.)
JAVADOC_AUTOBRIEF = NO
# If the QT_AUTOBRIEF tag is set to YES then Doxygen will
# interpret the first line (until the first dot) of a Qt-style
# comment as the brief description. If set to NO, the comments
# will behave just like regular Qt-style comments (thus requiring
# an explicit \brief command for a brief description.)
QT_AUTOBRIEF = NO
# The MULTILINE_CPP_IS_BRIEF tag can be set to YES to make Doxygen
# treat a multi-line C++ special comment block (i.e. a block of //! or ///
# comments) as a brief description. This used to be the default behaviour.
# The new default is to treat a multi-line C++ comment block as a detailed
# description. Set this tag to YES if you prefer the old behaviour instead.
MULTILINE_CPP_IS_BRIEF = NO
# If the INHERIT_DOCS tag is set to YES (the default) then an undocumented
# member inherits the documentation from any documented member that it
# re-implements.
INHERIT_DOCS = YES
# If the SEPARATE_MEMBER_PAGES tag is set to YES, then doxygen will produce
# a new page for each member. If set to NO, the documentation of a member will
# be part of the file/class/namespace that contains it.
SEPARATE_MEMBER_PAGES = NO
# The TAB_SIZE tag can be used to set the number of spaces in a tab.
# Doxygen uses this value to replace tabs by spaces in code fragments.
TAB_SIZE = 4
# This tag can be used to specify a number of aliases that acts
# as commands in the documentation. An alias has the form "name=value".
# For example adding "sideeffect=\par Side Effects:\n" will allow you to
# put the command \sideeffect (or @sideeffect) in the documentation, which
# will result in a user-defined paragraph with heading "Side Effects:".
# You can put \n's in the value part of an alias to insert newlines.
ALIASES =
# Set the OPTIMIZE_OUTPUT_FOR_C tag to YES if your project consists of C
# sources only. Doxygen will then generate output that is more tailored for C.
# For instance, some of the names that are used will be different. The list
# of all members will be omitted, etc.
OPTIMIZE_OUTPUT_FOR_C = YES
# Set the OPTIMIZE_OUTPUT_JAVA tag to YES if your project consists of Java
# sources only. Doxygen will then generate output that is more tailored for
# Java. For instance, namespaces will be presented as packages, qualified
# scopes will look different, etc.
OPTIMIZE_OUTPUT_JAVA = NO
# Set the OPTIMIZE_FOR_FORTRAN tag to YES if your project consists of Fortran
# sources only. Doxygen will then generate output that is more tailored for
# Fortran.
OPTIMIZE_FOR_FORTRAN = NO
# Set the OPTIMIZE_OUTPUT_VHDL tag to YES if your project consists of VHDL
# sources. Doxygen will then generate output that is tailored for
# VHDL.
OPTIMIZE_OUTPUT_VHDL = NO
# If you use STL classes (i.e. std::string, std::vector, etc.) but do not want
# to include (a tag file for) the STL sources as input, then you should
# set this tag to YES in order to let doxygen match functions declarations and
# definitions whose arguments contain STL classes (e.g. func(std::string); v.s.
# func(std::string) {}). This also make the inheritance and collaboration
# diagrams that involve STL classes more complete and accurate.
BUILTIN_STL_SUPPORT = NO
# If you use Microsoft's C++/CLI language, you should set this option to YES to
# enable parsing support.
CPP_CLI_SUPPORT = NO
# Set the SIP_SUPPORT tag to YES if your project consists of sip sources only.
# Doxygen will parse them like normal C++ but will assume all classes use public
# instead of private inheritance when no explicit protection keyword is present.
SIP_SUPPORT = NO
# For Microsoft's IDL there are propget and propput attributes to indicate getter
# and setter methods for a property. Setting this option to YES (the default)
# will make doxygen to replace the get and set methods by a property in the
# documentation. This will only work if the methods are indeed getting or
# setting a simple type. If this is not the case, or you want to show the
# methods anyway, you should set this option to NO.
IDL_PROPERTY_SUPPORT = YES
# If member grouping is used in the documentation and the DISTRIBUTE_GROUP_DOC
# tag is set to YES, then doxygen will reuse the documentation of the first
# member in the group (if any) for the other members of the group. By default
# all members of a group must be documented explicitly.
DISTRIBUTE_GROUP_DOC = NO
# Set the SUBGROUPING tag to YES (the default) to allow class member groups of
# the same type (for instance a group of public functions) to be put as a
# subgroup of that type (e.g. under the Public Functions section). Set it to
# NO to prevent subgrouping. Alternatively, this can be done per class using
# the \nosubgrouping command.
SUBGROUPING = YES
# When TYPEDEF_HIDES_STRUCT is enabled, a typedef of a struct, union, or enum
# is documented as struct, union, or enum with the name of the typedef. So
# typedef struct TypeS {} TypeT, will appear in the documentation as a struct
# with name TypeT. When disabled the typedef will appear as a member of a file,
# namespace, or class. And the struct will be named TypeS. This can typically
# be useful for C code in case the coding convention dictates that all compound
# types are typedef'ed and only the typedef is referenced, never the tag name.
TYPEDEF_HIDES_STRUCT = NO
# The SYMBOL_CACHE_SIZE determines the size of the internal cache use to
# determine which symbols to keep in memory and which to flush to disk.
# When the cache is full, less often used symbols will be written to disk.
# For small to medium size projects (<1000 input files) the default value is
# probably good enough. For larger projects a too small cache size can cause
# doxygen to be busy swapping symbols to and from disk most of the time
# causing a significant performance penality.
# If the system has enough physical memory increasing the cache will improve the
# performance by keeping more symbols in memory. Note that the value works on
# a logarithmic scale so increasing the size by one will rougly double the
# memory usage. The cache size is given by this formula:
# 2^(16+SYMBOL_CACHE_SIZE). The valid range is 0..9, the default is 0,
# corresponding to a cache size of 2^16 = 65536 symbols
SYMBOL_CACHE_SIZE = 0
#---------------------------------------------------------------------------
# Build related configuration options
#---------------------------------------------------------------------------
# If the EXTRACT_ALL tag is set to YES doxygen will assume all entities in
# documentation are documented, even if no documentation was available.
# Private class members and static file members will be hidden unless
# the EXTRACT_PRIVATE and EXTRACT_STATIC tags are set to YES
EXTRACT_ALL = YES
# If the EXTRACT_PRIVATE tag is set to YES all private members of a class
# will be included in the documentation.
EXTRACT_PRIVATE = YES
# If the EXTRACT_STATIC tag is set to YES all static members of a file
# will be included in the documentation.
EXTRACT_STATIC = YES
# If the EXTRACT_LOCAL_CLASSES tag is set to YES classes (and structs)
# defined locally in source files will be included in the documentation.
# If set to NO only classes defined in header files are included.
EXTRACT_LOCAL_CLASSES = YES
# This flag is only useful for Objective-C code. When set to YES local
# methods, which are defined in the implementation section but not in
# the interface are included in the documentation.
# If set to NO (the default) only methods in the interface are included.
EXTRACT_LOCAL_METHODS = NO
# If this flag is set to YES, the members of anonymous namespaces will be
# extracted and appear in the documentation as a namespace called
# 'anonymous_namespace{file}', where file will be replaced with the base
# name of the file that contains the anonymous namespace. By default
# anonymous namespace are hidden.
EXTRACT_ANON_NSPACES = NO
# If the HIDE_UNDOC_MEMBERS tag is set to YES, Doxygen will hide all
# undocumented members of documented classes, files or namespaces.
# If set to NO (the default) these members will be included in the
# various overviews, but no documentation section is generated.
# This option has no effect if EXTRACT_ALL is enabled.
HIDE_UNDOC_MEMBERS = NO
# If the HIDE_UNDOC_CLASSES tag is set to YES, Doxygen will hide all
# undocumented classes that are normally visible in the class hierarchy.
# If set to NO (the default) these classes will be included in the various
# overviews. This option has no effect if EXTRACT_ALL is enabled.
HIDE_UNDOC_CLASSES = NO
# If the HIDE_FRIEND_COMPOUNDS tag is set to YES, Doxygen will hide all
# friend (class|struct|union) declarations.
# If set to NO (the default) these declarations will be included in the
# documentation.
HIDE_FRIEND_COMPOUNDS = NO
# If the HIDE_IN_BODY_DOCS tag is set to YES, Doxygen will hide any
# documentation blocks found inside the body of a function.
# If set to NO (the default) these blocks will be appended to the
# function's detailed documentation block.
HIDE_IN_BODY_DOCS = NO
# The INTERNAL_DOCS tag determines if documentation
# that is typed after a \internal command is included. If the tag is set
# to NO (the default) then the documentation will be excluded.
# Set it to YES to include the internal documentation.
INTERNAL_DOCS = NO
# If the CASE_SENSE_NAMES tag is set to NO then Doxygen will only generate
# file names in lower-case letters. If set to YES upper-case letters are also
# allowed. This is useful if you have classes or files whose names only differ
# in case and if your file system supports case sensitive file names. Windows
# and Mac users are advised to set this option to NO.
CASE_SENSE_NAMES = NO
# If the HIDE_SCOPE_NAMES tag is set to NO (the default) then Doxygen
# will show members with their full class and namespace scopes in the
# documentation. If set to YES the scope will be hidden.
HIDE_SCOPE_NAMES = NO
# If the SHOW_INCLUDE_FILES tag is set to YES (the default) then Doxygen
# will put a list of the files that are included by a file in the documentation
# of that file.
SHOW_INCLUDE_FILES = YES
# If the INLINE_INFO tag is set to YES (the default) then a tag [inline]
# is inserted in the documentation for inline members.
INLINE_INFO = YES
# If the SORT_MEMBER_DOCS tag is set to YES (the default) then doxygen
# will sort the (detailed) documentation of file and class members
# alphabetically by member name. If set to NO the members will appear in
# declaration order.
SORT_MEMBER_DOCS = YES
# If the SORT_BRIEF_DOCS tag is set to YES then doxygen will sort the
# brief documentation of file, namespace and class members alphabetically
# by member name. If set to NO (the default) the members will appear in
# declaration order.
SORT_BRIEF_DOCS = NO
# If the SORT_GROUP_NAMES tag is set to YES then doxygen will sort the
# hierarchy of group names into alphabetical order. If set to NO (the default)
# the group names will appear in their defined order.
SORT_GROUP_NAMES = NO
# If the SORT_BY_SCOPE_NAME tag is set to YES, the class list will be
# sorted by fully-qualified names, including namespaces. If set to
# NO (the default), the class list will be sorted only by class name,
# not including the namespace part.
# Note: This option is not very useful if HIDE_SCOPE_NAMES is set to YES.
# Note: This option applies only to the class list, not to the
# alphabetical list.
SORT_BY_SCOPE_NAME = NO
# The GENERATE_TODOLIST tag can be used to enable (YES) or
# disable (NO) the todo list. This list is created by putting \todo
# commands in the documentation.
GENERATE_TODOLIST = NO
# The GENERATE_TESTLIST tag can be used to enable (YES) or
# disable (NO) the test list. This list is created by putting \test
# commands in the documentation.
GENERATE_TESTLIST = NO
# The GENERATE_BUGLIST tag can be used to enable (YES) or
# disable (NO) the bug list. This list is created by putting \bug
# commands in the documentation.
GENERATE_BUGLIST = NO
# The GENERATE_DEPRECATEDLIST tag can be used to enable (YES) or
# disable (NO) the deprecated list. This list is created by putting
# \deprecated commands in the documentation.
GENERATE_DEPRECATEDLIST= YES
# The ENABLED_SECTIONS tag can be used to enable conditional
# documentation sections, marked by \if sectionname ... \endif.
ENABLED_SECTIONS =
# The MAX_INITIALIZER_LINES tag determines the maximum number of lines
# the initial value of a variable or define consists of for it to appear in
# the documentation. If the initializer consists of more lines than specified
# here it will be hidden. Use a value of 0 to hide initializers completely.
# The appearance of the initializer of individual variables and defines in the
# documentation can be controlled using \showinitializer or \hideinitializer
# command in the documentation regardless of this setting.
MAX_INITIALIZER_LINES = 30
# Set the SHOW_USED_FILES tag to NO to disable the list of files generated
# at the bottom of the documentation of classes and structs. If set to YES the
# list will mention the files that were used to generate the documentation.
SHOW_USED_FILES = YES
# If the sources in your project are distributed over multiple directories
# then setting the SHOW_DIRECTORIES tag to YES will show the directory hierarchy
# in the documentation. The default is NO.
SHOW_DIRECTORIES = YES
# Set the SHOW_FILES tag to NO to disable the generation of the Files page.
# This will remove the Files entry from the Quick Index and from the
# Folder Tree View (if specified). The default is YES.
SHOW_FILES = YES
# Set the SHOW_NAMESPACES tag to NO to disable the generation of the
# Namespaces page. This will remove the Namespaces entry from the Quick Index
# and from the Folder Tree View (if specified). The default is YES.
SHOW_NAMESPACES = YES
# The FILE_VERSION_FILTER tag can be used to specify a program or script that
# doxygen should invoke to get the current version for each file (typically from
# the version control system). Doxygen will invoke the program by executing (via
# popen()) the command <command> <input-file>, where <command> is the value of
# the FILE_VERSION_FILTER tag, and <input-file> is the name of an input file
# provided by doxygen. Whatever the program writes to standard output
# is used as the file version. See the manual for examples.
FILE_VERSION_FILTER =
# The LAYOUT_FILE tag can be used to specify a layout file which will be parsed by
# doxygen. The layout file controls the global structure of the generated output files
# in an output format independent way. The create the layout file that represents
# doxygen's defaults, run doxygen with the -l option. You can optionally specify a
# file name after the option, if omitted DoxygenLayout.xml will be used as the name
# of the layout file.
LAYOUT_FILE =
#---------------------------------------------------------------------------
# configuration options related to warning and progress messages
#---------------------------------------------------------------------------
# The QUIET tag can be used to turn on/off the messages that are generated
# by doxygen. Possible values are YES and NO. If left blank NO is used.
QUIET = YES
# The WARNINGS tag can be used to turn on/off the warning messages that are
# generated by doxygen. Possible values are YES and NO. If left blank
# NO is used.
WARNINGS = YES
# If WARN_IF_UNDOCUMENTED is set to YES, then doxygen will generate warnings
# for undocumented members. If EXTRACT_ALL is set to YES then this flag will
# automatically be disabled.
WARN_IF_UNDOCUMENTED = YES
# If WARN_IF_DOC_ERROR is set to YES, doxygen will generate warnings for
# potential errors in the documentation, such as not documenting some
# parameters in a documented function, or documenting parameters that
# don't exist or using markup commands wrongly.
WARN_IF_DOC_ERROR = YES
# This WARN_NO_PARAMDOC option can be abled to get warnings for
# functions that are documented, but have no documentation for their parameters
# or return value. If set to NO (the default) doxygen will only warn about
# wrong or incomplete parameter documentation, but not about the absence of
# documentation.
WARN_NO_PARAMDOC = YES
# The WARN_FORMAT tag determines the format of the warning messages that
# doxygen can produce. The string should contain the $file, $line, and $text
# tags, which will be replaced by the file and line number from which the
# warning originated and the warning text. Optionally the format may contain
# $version, which will be replaced by the version of the file (if it could
# be obtained via FILE_VERSION_FILTER)
WARN_FORMAT = "$file:$line: $text"
# The WARN_LOGFILE tag can be used to specify a file to which warning
# and error messages should be written. If left blank the output is written
# to stderr.
WARN_LOGFILE =
#---------------------------------------------------------------------------
# configuration options related to the input files
#---------------------------------------------------------------------------
# The INPUT tag can be used to specify the files and/or directories that contain
# documented source files. You may enter file names like "myfile.cpp" or
# directories like "/usr/src/myproject". Separate the files or directories
# with spaces.
INPUT = ./
# This tag can be used to specify the character encoding of the source files
# that doxygen parses. Internally doxygen uses the UTF-8 encoding, which is
# also the default input encoding. Doxygen uses libiconv (or the iconv built
# into libc) for the transcoding. See http://www.gnu.org/software/libiconv for
# the list of possible encodings.
INPUT_ENCODING = UTF-8
# If the value of the INPUT tag contains directories, you can use the
# FILE_PATTERNS tag to specify one or more wildcard pattern (like *.cpp
# and *.h) to filter out the source-files in the directories. If left
# blank the following patterns are tested:
# *.c *.cc *.cxx *.cpp *.c++ *.java *.ii *.ixx *.ipp *.i++ *.inl *.h *.hh *.hxx
# *.hpp *.h++ *.idl *.odl *.cs *.php *.php3 *.inc *.m *.mm *.py *.f90
FILE_PATTERNS = *.h \
*.c \
*.txt
# The RECURSIVE tag can be used to turn specify whether or not subdirectories
# should be searched for input files as well. Possible values are YES and NO.
# If left blank NO is used.
RECURSIVE = YES
# The EXCLUDE tag can be used to specify files and/or directories that should
# excluded from the INPUT source files. This way you can easily exclude a
# subdirectory from a directory tree whose root is specified with the INPUT tag.
EXCLUDE =
# The EXCLUDE_SYMLINKS tag can be used select whether or not files or
# directories that are symbolic links (a Unix filesystem feature) are excluded
# from the input.
EXCLUDE_SYMLINKS = NO
# If the value of the INPUT tag contains directories, you can use the
# EXCLUDE_PATTERNS tag to specify one or more wildcard patterns to exclude
# certain files from those directories. Note that the wildcards are matched
# against the file with absolute path, so to exclude all test directories
# for example use the pattern */test/*
EXCLUDE_PATTERNS = */LowLevel/USBMode.h
# The EXCLUDE_SYMBOLS tag can be used to specify one or more symbol names
# (namespaces, classes, functions, etc.) that should be excluded from the
# output. The symbol name can be a fully qualified name, a word, or if the
# wildcard * is used, a substring. Examples: ANamespace, AClass,
# AClass::ANamespace, ANamespace::*Test
EXCLUDE_SYMBOLS = __*
# The EXAMPLE_PATH tag can be used to specify one or more files or
# directories that contain example code fragments that are included (see
# the \include command).
EXAMPLE_PATH =
# If the value of the EXAMPLE_PATH tag contains directories, you can use the
# EXAMPLE_PATTERNS tag to specify one or more wildcard pattern (like *.cpp
# and *.h) to filter out the source-files in the directories. If left
# blank all files are included.
EXAMPLE_PATTERNS = *
# If the EXAMPLE_RECURSIVE tag is set to YES then subdirectories will be
# searched for input files to be used with the \include or \dontinclude
# commands irrespective of the value of the RECURSIVE tag.
# Possible values are YES and NO. If left blank NO is used.
EXAMPLE_RECURSIVE = NO
# The IMAGE_PATH tag can be used to specify one or more files or
# directories that contain image that are included in the documentation (see
# the \image command).
IMAGE_PATH =
# The INPUT_FILTER tag can be used to specify a program that doxygen should
# invoke to filter for each input file. Doxygen will invoke the filter program
# by executing (via popen()) the command <filter> <input-file>, where <filter>
# is the value of the INPUT_FILTER tag, and <input-file> is the name of an
# input file. Doxygen will then use the output that the filter program writes
# to standard output. If FILTER_PATTERNS is specified, this tag will be
# ignored.
INPUT_FILTER =
# The FILTER_PATTERNS tag can be used to specify filters on a per file pattern
# basis. Doxygen will compare the file name with each pattern and apply the
# filter if there is a match. The filters are a list of the form:
# pattern=filter (like *.cpp=my_cpp_filter). See INPUT_FILTER for further
# info on how filters are used. If FILTER_PATTERNS is empty, INPUT_FILTER
# is applied to all files.
FILTER_PATTERNS =
# If the FILTER_SOURCE_FILES tag is set to YES, the input filter (if set using
# INPUT_FILTER) will be used to filter the input files when producing source
# files to browse (i.e. when SOURCE_BROWSER is set to YES).
FILTER_SOURCE_FILES = NO
#---------------------------------------------------------------------------
# configuration options related to source browsing
#---------------------------------------------------------------------------
# If the SOURCE_BROWSER tag is set to YES then a list of source files will
# be generated. Documented entities will be cross-referenced with these sources.
# Note: To get rid of all source code in the generated output, make sure also
# VERBATIM_HEADERS is set to NO.
SOURCE_BROWSER = NO
# Setting the INLINE_SOURCES tag to YES will include the body
# of functions and classes directly in the documentation.
INLINE_SOURCES = NO
# Setting the STRIP_CODE_COMMENTS tag to YES (the default) will instruct
# doxygen to hide any special comment blocks from generated source code
# fragments. Normal C and C++ comments will always remain visible.
STRIP_CODE_COMMENTS = YES
# If the REFERENCED_BY_RELATION tag is set to YES
# then for each documented function all documented
# functions referencing it will be listed.
REFERENCED_BY_RELATION = NO
# If the REFERENCES_RELATION tag is set to YES
# then for each documented function all documented entities
# called/used by that function will be listed.
REFERENCES_RELATION = NO
# If the REFERENCES_LINK_SOURCE tag is set to YES (the default)
# and SOURCE_BROWSER tag is set to YES, then the hyperlinks from
# functions in REFERENCES_RELATION and REFERENCED_BY_RELATION lists will
# link to the source code. Otherwise they will link to the documentstion.
REFERENCES_LINK_SOURCE = NO
# If the USE_HTAGS tag is set to YES then the references to source code
# will point to the HTML generated by the htags(1) tool instead of doxygen
# built-in source browser. The htags tool is part of GNU's global source
# tagging system (see http://www.gnu.org/software/global/global.html). You
# will need version 4.8.6 or higher.
USE_HTAGS = NO
# If the VERBATIM_HEADERS tag is set to YES (the default) then Doxygen
# will generate a verbatim copy of the header file for each class for
# which an include is specified. Set to NO to disable this.
VERBATIM_HEADERS = NO
#---------------------------------------------------------------------------
# configuration options related to the alphabetical class index
#---------------------------------------------------------------------------
# If the ALPHABETICAL_INDEX tag is set to YES, an alphabetical index
# of all compounds will be generated. Enable this if the project
# contains a lot of classes, structs, unions or interfaces.
ALPHABETICAL_INDEX = YES
# If the alphabetical index is enabled (see ALPHABETICAL_INDEX) then
# the COLS_IN_ALPHA_INDEX tag can be used to specify the number of columns
# in which this list will be split (can be a number in the range [1..20])
COLS_IN_ALPHA_INDEX = 5
# In case all classes in a project start with a common prefix, all
# classes will be put under the same header in the alphabetical index.
# The IGNORE_PREFIX tag can be used to specify one or more prefixes that
# should be ignored while generating the index headers.
IGNORE_PREFIX =
#---------------------------------------------------------------------------
# configuration options related to the HTML output
#---------------------------------------------------------------------------
# If the GENERATE_HTML tag is set to YES (the default) Doxygen will
# generate HTML output.
GENERATE_HTML = YES
# The HTML_OUTPUT tag is used to specify where the HTML docs will be put.
# If a relative path is entered the value of OUTPUT_DIRECTORY will be
# put in front of it. If left blank `html' will be used as the default path.
HTML_OUTPUT = html
# The HTML_FILE_EXTENSION tag can be used to specify the file extension for
# each generated HTML page (for example: .htm,.php,.asp). If it is left blank
# doxygen will generate files with .html extension.
HTML_FILE_EXTENSION = .html
# The HTML_HEADER tag can be used to specify a personal HTML header for
# each generated HTML page. If it is left blank doxygen will generate a
# standard header.
HTML_HEADER =
# The HTML_FOOTER tag can be used to specify a personal HTML footer for
# each generated HTML page. If it is left blank doxygen will generate a
# standard footer.
HTML_FOOTER =
# The HTML_STYLESHEET tag can be used to specify a user-defined cascading
# style sheet that is used by each HTML page. It can be used to
# fine-tune the look of the HTML output. If the tag is left blank doxygen
# will generate a default style sheet. Note that doxygen will try to copy
# the style sheet file to the HTML output directory, so don't put your own
# stylesheet in the HTML output directory as well, or it will be erased!
HTML_STYLESHEET =
# If the HTML_ALIGN_MEMBERS tag is set to YES, the members of classes,
# files or namespaces will be aligned in HTML using tables. If set to
# NO a bullet list will be used.
HTML_ALIGN_MEMBERS = YES
# If the HTML_DYNAMIC_SECTIONS tag is set to YES then the generated HTML
# documentation will contain sections that can be hidden and shown after the
# page has loaded. For this to work a browser that supports
# JavaScript and DHTML is required (for instance Mozilla 1.0+, Firefox
# Netscape 6.0+, Internet explorer 5.0+, Konqueror, or Safari).
HTML_DYNAMIC_SECTIONS = YES
# If the GENERATE_DOCSET tag is set to YES, additional index files
# will be generated that can be used as input for Apple's Xcode 3
# integrated development environment, introduced with OSX 10.5 (Leopard).
# To create a documentation set, doxygen will generate a Makefile in the
# HTML output directory. Running make will produce the docset in that
# directory and running "make install" will install the docset in
# ~/Library/Developer/Shared/Documentation/DocSets so that Xcode will find
# it at startup.
# See http://developer.apple.com/tools/creatingdocsetswithdoxygen.html for more information.
GENERATE_DOCSET = NO
# When GENERATE_DOCSET tag is set to YES, this tag determines the name of the
# feed. A documentation feed provides an umbrella under which multiple
# documentation sets from a single provider (such as a company or product suite)
# can be grouped.
DOCSET_FEEDNAME = "Doxygen generated docs"
# When GENERATE_DOCSET tag is set to YES, this tag specifies a string that
# should uniquely identify the documentation set bundle. This should be a
# reverse domain-name style string, e.g. com.mycompany.MyDocSet. Doxygen
# will append .docset to the name.
DOCSET_BUNDLE_ID = org.doxygen.Project
# If the GENERATE_HTMLHELP tag is set to YES, additional index files
# will be generated that can be used as input for tools like the
# Microsoft HTML help workshop to generate a compiled HTML help file (.chm)
# of the generated HTML documentation.
GENERATE_HTMLHELP = NO
# If the GENERATE_HTMLHELP tag is set to YES, the CHM_FILE tag can
# be used to specify the file name of the resulting .chm file. You
# can add a path in front of the file if the result should not be
# written to the html output directory.
CHM_FILE =
# If the GENERATE_HTMLHELP tag is set to YES, the HHC_LOCATION tag can
# be used to specify the location (absolute path including file name) of
# the HTML help compiler (hhc.exe). If non-empty doxygen will try to run
# the HTML help compiler on the generated index.hhp.
HHC_LOCATION =
# If the GENERATE_HTMLHELP tag is set to YES, the GENERATE_CHI flag
# controls if a separate .chi index file is generated (YES) or that
# it should be included in the master .chm file (NO).
GENERATE_CHI = NO
# If the GENERATE_HTMLHELP tag is set to YES, the CHM_INDEX_ENCODING
# is used to encode HtmlHelp index (hhk), content (hhc) and project file
# content.
CHM_INDEX_ENCODING =
# If the GENERATE_HTMLHELP tag is set to YES, the BINARY_TOC flag
# controls whether a binary table of contents is generated (YES) or a
# normal table of contents (NO) in the .chm file.
BINARY_TOC = NO
# The TOC_EXPAND flag can be set to YES to add extra items for group members
# to the contents of the HTML help documentation and to the tree view.
TOC_EXPAND = YES
# If the GENERATE_QHP tag is set to YES and both QHP_NAMESPACE and QHP_VIRTUAL_FOLDER
# are set, an additional index file will be generated that can be used as input for
# Qt's qhelpgenerator to generate a Qt Compressed Help (.qch) of the generated
# HTML documentation.
GENERATE_QHP = NO
# If the QHG_LOCATION tag is specified, the QCH_FILE tag can
# be used to specify the file name of the resulting .qch file.
# The path specified is relative to the HTML output folder.
QCH_FILE =
# The QHP_NAMESPACE tag specifies the namespace to use when generating
# Qt Help Project output. For more information please see
# <a href="http://doc.trolltech.com/qthelpproject.html#namespace">Qt Help Project / Namespace</a>.
QHP_NAMESPACE = org.doxygen.Project
# The QHP_VIRTUAL_FOLDER tag specifies the namespace to use when generating
# Qt Help Project output. For more information please see
# <a href="http://doc.trolltech.com/qthelpproject.html#virtual-folders">Qt Help Project / Virtual Folders</a>.
QHP_VIRTUAL_FOLDER = doc
# If the GENERATE_QHP tag is set to YES, the QHG_LOCATION tag can
# be used to specify the location of Qt's qhelpgenerator.
# If non-empty doxygen will try to run qhelpgenerator on the generated
# .qhp file .
QHG_LOCATION =
# The DISABLE_INDEX tag can be used to turn on/off the condensed index at
# top of each HTML page. The value NO (the default) enables the index and
# the value YES disables it.
DISABLE_INDEX = NO
# This tag can be used to set the number of enum values (range [1..20])
# that doxygen will group on one line in the generated HTML documentation.
ENUM_VALUES_PER_LINE = 1
# The GENERATE_TREEVIEW tag is used to specify whether a tree-like index
# structure should be generated to display hierarchical information.
# If the tag value is set to FRAME, a side panel will be generated
# containing a tree-like index structure (just like the one that
# is generated for HTML Help). For this to work a browser that supports
# JavaScript, DHTML, CSS and frames is required (for instance Mozilla 1.0+,
# Netscape 6.0+, Internet explorer 5.0+, or Konqueror). Windows users are
# probably better off using the HTML help feature. Other possible values
# for this tag are: HIERARCHIES, which will generate the Groups, Directories,
# and Class Hierarchy pages using a tree view instead of an ordered list;
# ALL, which combines the behavior of FRAME and HIERARCHIES; and NONE, which
# disables this behavior completely. For backwards compatibility with previous
# releases of Doxygen, the values YES and NO are equivalent to FRAME and NONE
# respectively.
GENERATE_TREEVIEW = YES
# If the treeview is enabled (see GENERATE_TREEVIEW) then this tag can be
# used to set the initial width (in pixels) of the frame in which the tree
# is shown.
TREEVIEW_WIDTH = 250
# Use this tag to change the font size of Latex formulas included
# as images in the HTML documentation. The default is 10. Note that
# when you change the font size after a successful doxygen run you need
# to manually remove any form_*.png images from the HTML output directory
# to force them to be regenerated.
FORMULA_FONTSIZE = 10
#---------------------------------------------------------------------------
# configuration options related to the LaTeX output
#---------------------------------------------------------------------------
# If the GENERATE_LATEX tag is set to YES (the default) Doxygen will
# generate Latex output.
GENERATE_LATEX = NO
# The LATEX_OUTPUT tag is used to specify where the LaTeX docs will be put.
# If a relative path is entered the value of OUTPUT_DIRECTORY will be
# put in front of it. If left blank `latex' will be used as the default path.
LATEX_OUTPUT = latex
# The LATEX_CMD_NAME tag can be used to specify the LaTeX command name to be
# invoked. If left blank `latex' will be used as the default command name.
LATEX_CMD_NAME = latex
# The MAKEINDEX_CMD_NAME tag can be used to specify the command name to
# generate index for LaTeX. If left blank `makeindex' will be used as the
# default command name.
MAKEINDEX_CMD_NAME = makeindex
# If the COMPACT_LATEX tag is set to YES Doxygen generates more compact
# LaTeX documents. This may be useful for small projects and may help to
# save some trees in general.
COMPACT_LATEX = NO
# The PAPER_TYPE tag can be used to set the paper type that is used
# by the printer. Possible values are: a4, a4wide, letter, legal and
# executive. If left blank a4wide will be used.
PAPER_TYPE = a4wide
# The EXTRA_PACKAGES tag can be to specify one or more names of LaTeX
# packages that should be included in the LaTeX output.
EXTRA_PACKAGES =
# The LATEX_HEADER tag can be used to specify a personal LaTeX header for
# the generated latex document. The header should contain everything until
# the first chapter. If it is left blank doxygen will generate a
# standard header. Notice: only use this tag if you know what you are doing!
LATEX_HEADER =
# If the PDF_HYPERLINKS tag is set to YES, the LaTeX that is generated
# is prepared for conversion to pdf (using ps2pdf). The pdf file will
# contain links (just like the HTML output) instead of page references
# This makes the output suitable for online browsing using a pdf viewer.
PDF_HYPERLINKS = YES
# If the USE_PDFLATEX tag is set to YES, pdflatex will be used instead of
# plain latex in the generated Makefile. Set this option to YES to get a
# higher quality PDF documentation.
USE_PDFLATEX = YES
# If the LATEX_BATCHMODE tag is set to YES, doxygen will add the \\batchmode.
# command to the generated LaTeX files. This will instruct LaTeX to keep
# running if errors occur, instead of asking the user for help.
# This option is also used when generating formulas in HTML.
LATEX_BATCHMODE = NO
# If LATEX_HIDE_INDICES is set to YES then doxygen will not
# include the index chapters (such as File Index, Compound Index, etc.)
# in the output.
LATEX_HIDE_INDICES = NO
#---------------------------------------------------------------------------
# configuration options related to the RTF output
#---------------------------------------------------------------------------
# If the GENERATE_RTF tag is set to YES Doxygen will generate RTF output
# The RTF output is optimized for Word 97 and may not look very pretty with
# other RTF readers or editors.
GENERATE_RTF = NO
# The RTF_OUTPUT tag is used to specify where the RTF docs will be put.
# If a relative path is entered the value of OUTPUT_DIRECTORY will be
# put in front of it. If left blank `rtf' will be used as the default path.
RTF_OUTPUT = rtf
# If the COMPACT_RTF tag is set to YES Doxygen generates more compact
# RTF documents. This may be useful for small projects and may help to
# save some trees in general.
COMPACT_RTF = NO
# If the RTF_HYPERLINKS tag is set to YES, the RTF that is generated
# will contain hyperlink fields. The RTF file will
# contain links (just like the HTML output) instead of page references.
# This makes the output suitable for online browsing using WORD or other
# programs which support those fields.
# Note: wordpad (write) and others do not support links.
RTF_HYPERLINKS = NO
# Load stylesheet definitions from file. Syntax is similar to doxygen's
# config file, i.e. a series of assignments. You only have to provide
# replacements, missing definitions are set to their default value.
RTF_STYLESHEET_FILE =
# Set optional variables used in the generation of an rtf document.
# Syntax is similar to doxygen's config file.
RTF_EXTENSIONS_FILE =
#---------------------------------------------------------------------------
# configuration options related to the man page output
#---------------------------------------------------------------------------
# If the GENERATE_MAN tag is set to YES (the default) Doxygen will
# generate man pages
GENERATE_MAN = NO
# The MAN_OUTPUT tag is used to specify where the man pages will be put.
# If a relative path is entered the value of OUTPUT_DIRECTORY will be
# put in front of it. If left blank `man' will be used as the default path.
MAN_OUTPUT = man
# The MAN_EXTENSION tag determines the extension that is added to
# the generated man pages (default is the subroutine's section .3)
MAN_EXTENSION = .3
# If the MAN_LINKS tag is set to YES and Doxygen generates man output,
# then it will generate one additional man file for each entity
# documented in the real man page(s). These additional files
# only source the real man page, but without them the man command
# would be unable to find the correct page. The default is NO.
MAN_LINKS = NO
#---------------------------------------------------------------------------
# configuration options related to the XML output
#---------------------------------------------------------------------------
# If the GENERATE_XML tag is set to YES Doxygen will
# generate an XML file that captures the structure of
# the code including all documentation.
GENERATE_XML = NO
# The XML_OUTPUT tag is used to specify where the XML pages will be put.
# If a relative path is entered the value of OUTPUT_DIRECTORY will be
# put in front of it. If left blank `xml' will be used as the default path.
XML_OUTPUT = xml
# The XML_SCHEMA tag can be used to specify an XML schema,
# which can be used by a validating XML parser to check the
# syntax of the XML files.
XML_SCHEMA =
# The XML_DTD tag can be used to specify an XML DTD,
# which can be used by a validating XML parser to check the
# syntax of the XML files.
XML_DTD =
# If the XML_PROGRAMLISTING tag is set to YES Doxygen will
# dump the program listings (including syntax highlighting
# and cross-referencing information) to the XML output. Note that
# enabling this will significantly increase the size of the XML output.
XML_PROGRAMLISTING = YES
#---------------------------------------------------------------------------
# configuration options for the AutoGen Definitions output
#---------------------------------------------------------------------------
# If the GENERATE_AUTOGEN_DEF tag is set to YES Doxygen will
# generate an AutoGen Definitions (see autogen.sf.net) file
# that captures the structure of the code including all
# documentation. Note that this feature is still experimental
# and incomplete at the moment.
GENERATE_AUTOGEN_DEF = NO
#---------------------------------------------------------------------------
# configuration options related to the Perl module output
#---------------------------------------------------------------------------
# If the GENERATE_PERLMOD tag is set to YES Doxygen will
# generate a Perl module file that captures the structure of
# the code including all documentation. Note that this
# feature is still experimental and incomplete at the
# moment.
GENERATE_PERLMOD = NO
# If the PERLMOD_LATEX tag is set to YES Doxygen will generate
# the necessary Makefile rules, Perl scripts and LaTeX code to be able
# to generate PDF and DVI output from the Perl module output.
PERLMOD_LATEX = NO
# If the PERLMOD_PRETTY tag is set to YES the Perl module output will be
# nicely formatted so it can be parsed by a human reader. This is useful
# if you want to understand what is going on. On the other hand, if this
# tag is set to NO the size of the Perl module output will be much smaller
# and Perl will parse it just the same.
PERLMOD_PRETTY = YES
# The names of the make variables in the generated doxyrules.make file
# are prefixed with the string contained in PERLMOD_MAKEVAR_PREFIX.
# This is useful so different doxyrules.make files included by the same
# Makefile don't overwrite each other's variables.
PERLMOD_MAKEVAR_PREFIX =
#---------------------------------------------------------------------------
# Configuration options related to the preprocessor
#---------------------------------------------------------------------------
# If the ENABLE_PREPROCESSING tag is set to YES (the default) Doxygen will
# evaluate all C-preprocessor directives found in the sources and include
# files.
ENABLE_PREPROCESSING = YES
# If the MACRO_EXPANSION tag is set to YES Doxygen will expand all macro
# names in the source code. If set to NO (the default) only conditional
# compilation will be performed. Macro expansion can be done in a controlled
# way by setting EXPAND_ONLY_PREDEF to YES.
MACRO_EXPANSION = YES
# If the EXPAND_ONLY_PREDEF and MACRO_EXPANSION tags are both set to YES
# then the macro expansion is limited to the macros specified with the
# PREDEFINED and EXPAND_AS_DEFINED tags.
EXPAND_ONLY_PREDEF = YES
# If the SEARCH_INCLUDES tag is set to YES (the default) the includes files
# in the INCLUDE_PATH (see below) will be search if a #include is found.
SEARCH_INCLUDES = YES
# The INCLUDE_PATH tag can be used to specify one or more directories that
# contain include files that are not input files but should be processed by
# the preprocessor.
INCLUDE_PATH =
# You can use the INCLUDE_FILE_PATTERNS tag to specify one or more wildcard
# patterns (like *.h and *.hpp) to filter out the header-files in the
# directories. If left blank, the patterns specified with FILE_PATTERNS will
# be used.
INCLUDE_FILE_PATTERNS =
# The PREDEFINED tag can be used to specify one or more macro names that
# are defined before the preprocessor is started (similar to the -D option of
# gcc). The argument of the tag is a list of macros of the form: name
# or name=definition (no spaces). If the definition and the = are
# omitted =1 is assumed. To prevent a macro definition from being
# undefined via #undef or recursively expanded use the := operator
# instead of the = operator.
PREDEFINED = __DOXYGEN__
# If the MACRO_EXPANSION and EXPAND_ONLY_PREDEF tags are set to YES then
# this tag can be used to specify a list of macro names that should be expanded.
# The macro definition that is found in the sources will be used.
# Use the PREDEFINED tag if you want to use a different macro definition.
EXPAND_AS_DEFINED = BUTTLOADTAG
# If the SKIP_FUNCTION_MACROS tag is set to YES (the default) then
# doxygen's preprocessor will remove all function-like macros that are alone
# on a line, have an all uppercase name, and do not end with a semicolon. Such
# function macros are typically used for boiler-plate code, and will confuse
# the parser if not removed.
SKIP_FUNCTION_MACROS = YES
#---------------------------------------------------------------------------
# Configuration::additions related to external references
#---------------------------------------------------------------------------
# The TAGFILES option can be used to specify one or more tagfiles.
# Optionally an initial location of the external documentation
# can be added for each tagfile. The format of a tag file without
# this location is as follows:
# TAGFILES = file1 file2 ...
# Adding location for the tag files is done as follows:
# TAGFILES = file1=loc1 "file2 = loc2" ...
# where "loc1" and "loc2" can be relative or absolute paths or
# URLs. If a location is present for each tag, the installdox tool
# does not have to be run to correct the links.
# Note that each tag file must have a unique name
# (where the name does NOT include the path)
# If a tag file is not located in the directory in which doxygen
# is run, you must also specify the path to the tagfile here.
TAGFILES =
# When a file name is specified after GENERATE_TAGFILE, doxygen will create
# a tag file that is based on the input files it reads.
GENERATE_TAGFILE =
# If the ALLEXTERNALS tag is set to YES all external classes will be listed
# in the class index. If set to NO only the inherited external classes
# will be listed.
ALLEXTERNALS = NO
# If the EXTERNAL_GROUPS tag is set to YES all external groups will be listed
# in the modules index. If set to NO, only the current project's groups will
# be listed.
EXTERNAL_GROUPS = YES
# The PERL_PATH should be the absolute path and name of the perl script
# interpreter (i.e. the result of `which perl').
PERL_PATH = /usr/bin/perl
#---------------------------------------------------------------------------
# Configuration options related to the dot tool
#---------------------------------------------------------------------------
# If the CLASS_DIAGRAMS tag is set to YES (the default) Doxygen will
# generate a inheritance diagram (in HTML, RTF and LaTeX) for classes with base
# or super classes. Setting the tag to NO turns the diagrams off. Note that
# this option is superseded by the HAVE_DOT option below. This is only a
# fallback. It is recommended to install and use dot, since it yields more
# powerful graphs.
CLASS_DIAGRAMS = NO
# You can define message sequence charts within doxygen comments using the \msc
# command. Doxygen will then run the mscgen tool (see
# http://www.mcternan.me.uk/mscgen/) to produce the chart and insert it in the
# documentation. The MSCGEN_PATH tag allows you to specify the directory where
# the mscgen tool resides. If left empty the tool is assumed to be found in the
# default search path.
MSCGEN_PATH =
# If set to YES, the inheritance and collaboration graphs will hide
# inheritance and usage relations if the target is undocumented
# or is not a class.
HIDE_UNDOC_RELATIONS = YES
# If you set the HAVE_DOT tag to YES then doxygen will assume the dot tool is
# available from the path. This tool is part of Graphviz, a graph visualization
# toolkit from AT&T and Lucent Bell Labs. The other options in this section
# have no effect if this option is set to NO (the default)
HAVE_DOT = NO
# By default doxygen will write a font called FreeSans.ttf to the output
# directory and reference it in all dot files that doxygen generates. This
# font does not include all possible unicode characters however, so when you need
# these (or just want a differently looking font) you can specify the font name
# using DOT_FONTNAME. You need need to make sure dot is able to find the font,
# which can be done by putting it in a standard location or by setting the
# DOTFONTPATH environment variable or by setting DOT_FONTPATH to the directory
# containing the font.
DOT_FONTNAME = FreeSans
# The DOT_FONTSIZE tag can be used to set the size of the font of dot graphs.
# The default size is 10pt.
DOT_FONTSIZE = 10
# By default doxygen will tell dot to use the output directory to look for the
# FreeSans.ttf font (which doxygen will put there itself). If you specify a
# different font using DOT_FONTNAME you can set the path where dot
# can find it using this tag.
DOT_FONTPATH =
# If the CLASS_GRAPH and HAVE_DOT tags are set to YES then doxygen
# will generate a graph for each documented class showing the direct and
# indirect inheritance relations. Setting this tag to YES will force the
# the CLASS_DIAGRAMS tag to NO.
CLASS_GRAPH = NO
# If the COLLABORATION_GRAPH and HAVE_DOT tags are set to YES then doxygen
# will generate a graph for each documented class showing the direct and
# indirect implementation dependencies (inheritance, containment, and
# class references variables) of the class with other documented classes.
COLLABORATION_GRAPH = NO
# If the GROUP_GRAPHS and HAVE_DOT tags are set to YES then doxygen
# will generate a graph for groups, showing the direct groups dependencies
GROUP_GRAPHS = NO
# If the UML_LOOK tag is set to YES doxygen will generate inheritance and
# collaboration diagrams in a style similar to the OMG's Unified Modeling
# Language.
UML_LOOK = NO
# If set to YES, the inheritance and collaboration graphs will show the
# relations between templates and their instances.
TEMPLATE_RELATIONS = NO
# If the ENABLE_PREPROCESSING, SEARCH_INCLUDES, INCLUDE_GRAPH, and HAVE_DOT
# tags are set to YES then doxygen will generate a graph for each documented
# file showing the direct and indirect include dependencies of the file with
# other documented files.
INCLUDE_GRAPH = NO
# If the ENABLE_PREPROCESSING, SEARCH_INCLUDES, INCLUDED_BY_GRAPH, and
# HAVE_DOT tags are set to YES then doxygen will generate a graph for each
# documented header file showing the documented files that directly or
# indirectly include this file.
INCLUDED_BY_GRAPH = NO
# If the CALL_GRAPH and HAVE_DOT options are set to YES then
# doxygen will generate a call dependency graph for every global function
# or class method. Note that enabling this option will significantly increase
# the time of a run. So in most cases it will be better to enable call graphs
# for selected functions only using the \callgraph command.
CALL_GRAPH = NO
# If the CALLER_GRAPH and HAVE_DOT tags are set to YES then
# doxygen will generate a caller dependency graph for every global function
# or class method. Note that enabling this option will significantly increase
# the time of a run. So in most cases it will be better to enable caller
# graphs for selected functions only using the \callergraph command.
CALLER_GRAPH = NO
# If the GRAPHICAL_HIERARCHY and HAVE_DOT tags are set to YES then doxygen
# will graphical hierarchy of all classes instead of a textual one.
GRAPHICAL_HIERARCHY = NO
# If the DIRECTORY_GRAPH, SHOW_DIRECTORIES and HAVE_DOT tags are set to YES
# then doxygen will show the dependencies a directory has on other directories
# in a graphical way. The dependency relations are determined by the #include
# relations between the files in the directories.
DIRECTORY_GRAPH = NO
# The DOT_IMAGE_FORMAT tag can be used to set the image format of the images
# generated by dot. Possible values are png, jpg, or gif
# If left blank png will be used.
DOT_IMAGE_FORMAT = png
# The tag DOT_PATH can be used to specify the path where the dot tool can be
# found. If left blank, it is assumed the dot tool can be found in the path.
DOT_PATH = "C:/Program Files/Graphviz2.18/bin"
# The DOTFILE_DIRS tag can be used to specify one or more directories that
# contain dot files that are included in the documentation (see the
# \dotfile command).
DOTFILE_DIRS =
# The DOT_GRAPH_MAX_NODES tag can be used to set the maximum number of
# nodes that will be shown in the graph. If the number of nodes in a graph
# becomes larger than this value, doxygen will truncate the graph, which is
# visualized by representing a node as a red box. Note that doxygen if the
# number of direct children of the root node in a graph is already larger than
# DOT_GRAPH_MAX_NODES then the graph will not be shown at all. Also note
# that the size of a graph can be further restricted by MAX_DOT_GRAPH_DEPTH.
DOT_GRAPH_MAX_NODES = 15
# The MAX_DOT_GRAPH_DEPTH tag can be used to set the maximum depth of the
# graphs generated by dot. A depth value of 3 means that only nodes reachable
# from the root by following a path via at most 3 edges will be shown. Nodes
# that lay further from the root node will be omitted. Note that setting this
# option to 1 or 2 may greatly reduce the computation time needed for large
# code bases. Also note that the size of a graph can be further restricted by
# DOT_GRAPH_MAX_NODES. Using a depth of 0 means no depth restriction.
MAX_DOT_GRAPH_DEPTH = 2
# Set the DOT_TRANSPARENT tag to YES to generate images with a transparent
# background. This is disabled by default, because dot on Windows does not
# seem to support this out of the box. Warning: Depending on the platform used,
# enabling this option may lead to badly anti-aliased labels on the edges of
# a graph (i.e. they become hard to read).
DOT_TRANSPARENT = YES
# Set the DOT_MULTI_TARGETS tag to YES allow dot to generate multiple output
# files in one run (i.e. multiple -o and -T options on the command line). This
# makes dot run faster, but since only newer versions of dot (>1.8.10)
# support this, this feature is disabled by default.
DOT_MULTI_TARGETS = NO
# If the GENERATE_LEGEND tag is set to YES (the default) Doxygen will
# generate a legend page explaining the meaning of the various boxes and
# arrows in the dot generated graphs.
GENERATE_LEGEND = YES
# If the DOT_CLEANUP tag is set to YES (the default) Doxygen will
# remove the intermediate dot files that are used to generate
# the various graphs.
DOT_CLEANUP = YES
#---------------------------------------------------------------------------
# Configuration::additions related to the search engine
#---------------------------------------------------------------------------
# The SEARCHENGINE tag specifies whether or not a search engine should be
# used. If set to NO the values of all tags below this one will be ignored.
SEARCHENGINE = NO

@ -0,0 +1 @@
<AVRStudio><MANAGEMENT><ProjectName>Magstripe</ProjectName><Created>30-Sep-2008 14:19:14</Created><LastEdit>30-Sep-2008 14:19:28</LastEdit><ICON>241</ICON><ProjectType>0</ProjectType><Created>30-Sep-2008 14:19:14</Created><Version>4</Version><Build>4, 14, 0, 589</Build><ProjectTypeName>AVR GCC</ProjectTypeName></MANAGEMENT><CODE_CREATION><ObjectFile></ObjectFile><EntryFile></EntryFile><SaveFolder>C:\Users\Dean\Documents\Electronics\Projects\WORK\MyUSBWORK\Projects\Magstripe\</SaveFolder></CODE_CREATION><DEBUG_TARGET><CURRENT_TARGET></CURRENT_TARGET><CURRENT_PART></CURRENT_PART><BREAKPOINTS></BREAKPOINTS><IO_EXPAND><HIDE>false</HIDE></IO_EXPAND><REGISTERNAMES><Register>R00</Register><Register>R01</Register><Register>R02</Register><Register>R03</Register><Register>R04</Register><Register>R05</Register><Register>R06</Register><Register>R07</Register><Register>R08</Register><Register>R09</Register><Register>R10</Register><Register>R11</Register><Register>R12</Register><Register>R13</Register><Register>R14</Register><Register>R15</Register><Register>R16</Register><Register>R17</Register><Register>R18</Register><Register>R19</Register><Register>R20</Register><Register>R21</Register><Register>R22</Register><Register>R23</Register><Register>R24</Register><Register>R25</Register><Register>R26</Register><Register>R27</Register><Register>R28</Register><Register>R29</Register><Register>R30</Register><Register>R31</Register></REGISTERNAMES><COM>Auto</COM><COMType>0</COMType><WATCHNUM>0</WATCHNUM><WATCHNAMES><Pane0></Pane0><Pane1></Pane1><Pane2></Pane2><Pane3></Pane3></WATCHNAMES><BreakOnTrcaeFull>0</BreakOnTrcaeFull></DEBUG_TARGET><Debugger><Triggers></Triggers></Debugger><AVRGCCPLUGIN><FILES><SOURCEFILE>Descriptors.c</SOURCEFILE><SOURCEFILE>Magstripe.c</SOURCEFILE><HEADERFILE>Descriptors.h</HEADERFILE><HEADERFILE>Magstripe.h</HEADERFILE><HEADERFILE>MagstripeHW.h</HEADERFILE><OTHERFILE>makefile</OTHERFILE></FILES><CONFIGS><CONFIG><NAME>default</NAME><USESEXTERNALMAKEFILE>YES</USESEXTERNALMAKEFILE><EXTERNALMAKEFILE>makefile</EXTERNALMAKEFILE><PART>atmega128</PART><HEX>1</HEX><LIST>1</LIST><MAP>1</MAP><OUTPUTFILENAME>Magstripe.elf</OUTPUTFILENAME><OUTPUTDIR>default\</OUTPUTDIR><ISDIRTY>1</ISDIRTY><OPTIONS/><INCDIRS/><LIBDIRS/><LIBS/><LINKOBJECTS/><OPTIONSFORALL>-Wall -gdwarf-2 -std=gnu99 -Os -funsigned-char -funsigned-bitfields -fpack-struct -fshort-enums</OPTIONSFORALL><LINKEROPTIONS></LINKEROPTIONS><SEGMENTS/></CONFIG></CONFIGS><LASTCONFIG>default</LASTCONFIG><USES_WINAVR>1</USES_WINAVR><GCC_LOC>C:\WinAVR-20080512\bin\avr-gcc.exe</GCC_LOC><MAKE_LOC>C:\WinAVR-20080512\utils\bin\make.exe</MAKE_LOC></AVRGCCPLUGIN><IOView><usergroups/><sort sorted="0" column="0" ordername="0" orderaddress="0" ordergroup="0"/></IOView><Files></Files><Events><Bookmarks></Bookmarks></Events><Trace><Filters></Filters></Trace></AVRStudio>

@ -0,0 +1,436 @@
/*
LUFA Library
Copyright (C) Dean Camera, 2009.
dean [at] fourwalledcubicle [dot] com
www.fourwalledcubicle.com
*/
/*
Copyright 2009 Denver Gingerich (denver [at] ossguy [dot] com)
Copyright 2009 Dean Camera (dean [at] fourwalledcubicle [dot] com)
Permission to use, copy, modify, and distribute this software
and its documentation for any purpose and without fee is hereby
granted, provided that the above copyright notice appear in all
copies and that both that the copyright notice and this
permission notice and warranty disclaimer appear in supporting
documentation, and that the name of the author not be used in
advertising or publicity pertaining to distribution of the
software without specific, written prior permission.
The author disclaim all warranties with regard to this
software, including all implied warranties of merchantability
and fitness. In no event shall the author be liable for any
special, indirect or consequential damages or any damages
whatsoever resulting from loss of use, data or profits, whether
in an action of contract, negligence or other tortious action,
arising out of or in connection with the use or performance of
this software.
*/
/** \file
*
* Main source file for the MagStripe application. This file contains the code which drives
* the USB keyboard interface from the magnetic card stripe reader device.
*/
#include "Magstripe.h"
/* Project Tags, for reading out using the ButtLoad project */
BUTTLOADTAG(ProjName, "Magstripe Reader");
BUTTLOADTAG(BuildTime, __TIME__);
BUTTLOADTAG(BuildDate, __DATE__);
BUTTLOADTAG(LUFAVersion, "LUFA V" LUFA_VERSION_STRING);
/* Scheduler Task List */
TASK_LIST
{
{ Task: USB_USBTask , TaskStatus: TASK_STOP },
{ Task: USB_Keyboard_Report , TaskStatus: TASK_STOP },
{ Task: Magstripe_Read , TaskStatus: TASK_STOP },
};
/* Global Variables */
/** Indicates if the device is using Report Protocol mode, instead of Boot Protocol mode. Boot Protocol mode
* is a special reporting mode used by compatible PC BIOS to support USB keyboards before a full OS and USB
* driver has been loaded, by using predefined report structures indicated in the USB HID standard.
*/
bool UsingReportProtocol = true;
/** Total idle period in milliseconds set by the host via a SetIdle request, used to silence the report endpoint
* until the report data changes or the idle period elapsed. Generally used to implement hardware key repeats, or
* by some BIOS to reduce the number of reports when in Boot Protocol mode.
*/
uint8_t IdleCount = 0;
/** Milliseconds remaining counter for the HID class SetIdle and GetIdle requests, used to silence the report
* endpoint for an amount of time indicated by the host or until the report changes.
*/
uint16_t IdleMSRemaining = 0;
/** Circular buffer to hold the read bits from track 1 of the inserted magnetic card. */
BitBuffer_t Track1Data;
/** Circular buffer to hold the read bits from track 2 of the inserted magnetic card. */
BitBuffer_t Track2Data;
/** Circular buffer to hold the read bits from track 3 of the inserted magnetic card. */
BitBuffer_t Track3Data;
/** Delay counter between sucessive key strokes. This is to prevent the OS from ignoring multiple keys in a short
* period of time due to key repeats. Two milliseconds works for most OSes.
*/
uint8_t KeyDelayRemaining;
/** Main program entry point. This routine configures the hardware required by the application, then
* starts the scheduler to run the application tasks.
*/
int main(void)
{
/* Disable watchdog if enabled by bootloader/fuses */
MCUSR &= ~(1 << WDRF);
wdt_disable();
/* Disable Clock Division */
SetSystemClockPrescaler(0);
/* Hardware Initialization */
Magstripe_Init();
/* Buffer Initialization */
BitBuffer_Init(&Track1Data);
BitBuffer_Init(&Track2Data);
BitBuffer_Init(&Track3Data);
/* Millisecond timer initialization, with output compare interrupt enabled for the idle timing */
OCR0A = 0xFA;
TCCR0A = (1 << WGM01);
TCCR0B = ((1 << CS01) | (1 << CS00));
TIMSK0 = (1 << OCIE0A);
/* Initialize Scheduler so that it can be used */
Scheduler_Init();
/* Initialize USB Subsystem */
USB_Init();
/* Scheduling - routine never returns, so put this last in the main function */
Scheduler_Start();
}
/** Event handler for the USB_Connect event. This starts the USB task. */
EVENT_HANDLER(USB_Connect)
{
/* Start USB management task */
Scheduler_SetTaskMode(USB_USBTask, TASK_RUN);
}
/** Event handler for the USB_Disconnect event. This stops the USB and keyboard report tasks. */
EVENT_HANDLER(USB_Disconnect)
{
/* Stop running keyboard reporting, card reading and USB management tasks */
Scheduler_SetTaskMode(USB_Keyboard_Report, TASK_STOP);
Scheduler_SetTaskMode(USB_USBTask, TASK_STOP);
Scheduler_SetTaskMode(Magstripe_Read, TASK_STOP);
}
/** Event handler for the USB_ConfigurationChanged event. This configures the device's endpoints ready
* to relay reports to the host, and starts the keyboard report task.
*/
EVENT_HANDLER(USB_ConfigurationChanged)
{
/* Setup Keyboard Keycode Report Endpoint */
Endpoint_ConfigureEndpoint(KEYBOARD_EPNUM, EP_TYPE_INTERRUPT,
ENDPOINT_DIR_IN, KEYBOARD_EPSIZE,
ENDPOINT_BANK_SINGLE);
/* Default to report protocol on connect */
UsingReportProtocol = true;
/* Start Keyboard reporting and card reading tasks */
Scheduler_SetTaskMode(USB_Keyboard_Report, TASK_RUN);
Scheduler_SetTaskMode(Magstripe_Read, TASK_RUN);
}
/** Event handler for the USB_UnhandledControlPacket event. This is used to catch standard and class specific
* control requests that are not handled internally by the USB library, so that they can be handled appropriately
* for the application.
*/
EVENT_HANDLER(USB_UnhandledControlPacket)
{
/* Handle HID Class specific requests */
switch (bRequest)
{
case REQ_GetReport:
if (bmRequestType == (REQDIR_DEVICETOHOST | REQTYPE_CLASS | REQREC_INTERFACE))
{
USB_KeyboardReport_Data_t KeyboardReportData;
/* Create the next keyboard report for transmission to the host */
GetNextReport(&KeyboardReportData);
/* Ignore report type and ID number value */
Endpoint_Discard_Word();
/* Ignore unused Interface number value */
Endpoint_Discard_Word();
/* Read in the number of bytes in the report to send to the host */
uint16_t wLength = Endpoint_Read_Word_LE();
/* If trying to send more bytes than exist to the host, clamp the value at the report size */
if (wLength > sizeof(KeyboardReportData))
wLength = sizeof(KeyboardReportData);
Endpoint_ClearSetupReceived();
/* Write the report data to the control endpoint */
Endpoint_Write_Control_Stream_LE(&KeyboardReportData, wLength);
/* Finalize the stream transfer to send the last packet or clear the host abort */
Endpoint_ClearSetupOUT();
}
break;
case REQ_GetProtocol:
if (bmRequestType == (REQDIR_DEVICETOHOST | REQTYPE_CLASS | REQREC_INTERFACE))
{
Endpoint_ClearSetupReceived();
/* Write the current protocol flag to the host */
Endpoint_Write_Byte(UsingReportProtocol);
/* Send the flag to the host */
Endpoint_ClearSetupIN();
}
break;
case REQ_SetProtocol:
if (bmRequestType == (REQDIR_HOSTTODEVICE | REQTYPE_CLASS | REQREC_INTERFACE))
{
/* Read in the wValue parameter containing the new protocol mode */
uint16_t wValue = Endpoint_Read_Word_LE();
Endpoint_ClearSetupReceived();
/* Set or clear the flag depending on what the host indicates that the current Protocol should be */
UsingReportProtocol = (wValue != 0x0000);
/* Send an empty packet to acknowedge the command */
Endpoint_ClearSetupIN();
}
break;
case REQ_SetIdle:
if (bmRequestType == (REQDIR_HOSTTODEVICE | REQTYPE_CLASS | REQREC_INTERFACE))
{
/* Read in the wValue parameter containing the idle period */
uint16_t wValue = Endpoint_Read_Word_LE();
Endpoint_ClearSetupReceived();
/* Get idle period in MSB */
IdleCount = (wValue >> 8);
/* Send an empty packet to acknowedge the command */
Endpoint_ClearSetupIN();
}
break;
case REQ_GetIdle:
if (bmRequestType == (REQDIR_DEVICETOHOST | REQTYPE_CLASS | REQREC_INTERFACE))
{
Endpoint_ClearSetupReceived();
/* Write the current idle duration to the host */
Endpoint_Write_Byte(IdleCount);
/* Send the flag to the host */
Endpoint_ClearSetupIN();
}
break;
}
}
/** ISR for the timer 0 compare vector. This ISR fires once each millisecond, and decrements the counter indicating
* the number of milliseconds left to idle (not send the host reports) if the device has been instructed to idle
* by the host via a SetIdle class specific request.
*/
ISR(TIMER0_COMPA_vect, ISR_BLOCK)
{
/* One millisecond has elapsed, decrement the idle time remaining counter if it has not already elapsed */
if (IdleMSRemaining)
IdleMSRemaining--;
if (KeyDelayRemaining)
KeyDelayRemaining--;
}
/** Constructs a keyboard report indicating the currently pressed keyboard keys to the host.
*
* \param ReportData Pointer to a USB_KeyboardReport_Data_t report structure where the resulting report should
* be stored
*
* \return Boolean true if the current report is different to the previous report, false otherwise
*/
bool GetNextReport(USB_KeyboardReport_Data_t* ReportData)
{
static bool OddReport = false;
static bool MustRelease = false;
BitBuffer_t* Buffer = NULL;
/* Clear the report contents */
memset(ReportData, 0, sizeof(USB_KeyboardReport_Data_t));
/* Get the next non-empty track data buffer */
if (Track1Data.Elements)
Buffer = &Track1Data;
else if (Track2Data.Elements)
Buffer = &Track2Data;
else if (Track3Data.Elements)
Buffer = &Track3Data;
if (Buffer != NULL)
{
/* Toggle the odd report number indicator */
OddReport = !OddReport;
/* Set the flag indicating that a null report must eventually be sent to release all pressed keys */
MustRelease = true;
/* Only send the next key on odd reports, so that they are interpersed with null reports to release keys */
if (OddReport)
{
/* Set the report key code to the key code for the next data bit */
ReportData->KeyCode[0] = BitBuffer_GetNextBit(Buffer) ? KEY_1 : KEY_0;
/* If buffer is now empty, a new line must be sent instead of the terminating bit */
if (!(Buffer->Elements))
{
/* Set the keycode to the code for an enter key press */
ReportData->KeyCode[0] = KEY_ENTER;
}
}
return true;
}
else if (MustRelease)
{
/* Leave key code to null (0), to release all pressed keys */
return true;
}
return false;
}
/** Task to read out data from inserted magnetic cards and place the seperate track data into their respective
* data buffers for later sending to the host as keyboard key presses.
*/
TASK(Magstripe_Read)
{
/* Arrays to hold the buffer pointers, clock and data bit masks for the seperate card tracks */
const struct
{
BitBuffer_t* Buffer;
uint8_t ClockMask;
uint8_t DataMask;
} TrackInfo[] = {{&Track1Data, MAG_T1_CLOCK, MAG_T1_DATA},
{&Track2Data, MAG_T2_CLOCK, MAG_T2_DATA},
{&Track3Data, MAG_T3_CLOCK, MAG_T3_DATA}};
/* Previous magnetic card control line' status, for later comparison */
uint8_t Magstripe_Prev = 0;
/* Buffered current card reader control line' status */
uint8_t Magstripe_LCL = Magstripe_GetStatus();
/* Exit the task early if no card is present in the reader */
if (!(Magstripe_LCL & MAG_CARDPRESENT))
return;
/* Read out card data while a card is present */
while (Magstripe_LCL & MAG_CARDPRESENT)
{
/* Read out the next bit for each track of the card */
for (uint8_t Track = 0; Track < 3; Track++)
{
/* Current data line status for the current card track */
bool DataLevel = ((Magstripe_LCL & TrackInfo[Track].DataMask) != 0);
/* Current clock line status for the current card track */
bool ClockLevel = ((Magstripe_LCL & TrackInfo[Track].ClockMask) != 0);
/* Current track clock transition check */
bool ClockChanged = (((Magstripe_LCL ^ Magstripe_Prev) & TrackInfo[Track].ClockMask) != 0);
/* Sample the next bit on the falling edge of the track's clock line, store key code into the track's buffer */
if (ClockLevel && ClockChanged)
BitBuffer_StoreNextBit(TrackInfo[Track].Buffer, DataLevel);
}
/* Retain the current card reader control line states for later edge detection */
Magstripe_Prev = Magstripe_LCL;
/* Retrieve the new card reader control line states */
Magstripe_LCL = Magstripe_GetStatus();
}
/* Add terminators to the end of each track buffer */
BitBuffer_StoreNextBit(&Track1Data, 0);
BitBuffer_StoreNextBit(&Track2Data, 0);
BitBuffer_StoreNextBit(&Track3Data, 0);
}
/** Task for the magnetic card reading and keyboard report generation. This task waits until a card is inserted,
* then reads off the card data and sends it to the host as a series of keyboard keypresses via keyboard reports.
*/
TASK(USB_Keyboard_Report)
{
USB_KeyboardReport_Data_t KeyboardReportData;
bool SendReport = false;
/* Check if the USB system is connected to a host */
if (USB_IsConnected)
{
/* Select the Keyboard Report Endpoint */
Endpoint_SelectEndpoint(KEYBOARD_EPNUM);
/* Check if Keyboard Endpoint Ready for Read/Write */
if (Endpoint_ReadWriteAllowed())
{
/* Only fetch the next key to send once the period between key presses has elapsed */
if (!(KeyDelayRemaining))
{
/* Create the next keyboard report for transmission to the host */
SendReport = GetNextReport(&KeyboardReportData);
}
/* Check if the idle period is set and has elapsed */
if (IdleCount && !(IdleMSRemaining))
{
/* Idle period elapsed, indicate that a report must be sent */
SendReport = true;
/* Reset the idle time remaining counter, must multiply by 4 to get the duration in milliseconds */
IdleMSRemaining = (IdleCount << 2);
}
/* Write the keyboard report if a report is to be sent to the host */
if (SendReport)
{
/* Write Keyboard Report Data */
Endpoint_Write_Stream_LE(&KeyboardReportData, sizeof(USB_KeyboardReport_Data_t));
/* Finalize the stream transfer to send the last packet */
Endpoint_ClearCurrentBank();
/* Reset the key delay period counter */
KeyDelayRemaining = 2;
}
}
}
}

@ -0,0 +1,121 @@
/*
LUFA Library
Copyright (C) Dean Camera, 2009.
dean [at] fourwalledcubicle [dot] com
www.fourwalledcubicle.com
*/
/*
Copyright 2009 Denver Gingerich (denver [at] ossguy [dot] com)
Copyright 2009 Dean Camera (dean [at] fourwalledcubicle [dot] com)
Permission to use, copy, modify, and distribute this software
and its documentation for any purpose and without fee is hereby
granted, provided that the above copyright notice appear in all
copies and that both that the copyright notice and this
permission notice and warranty disclaimer appear in supporting
documentation, and that the name of the author not be used in
advertising or publicity pertaining to distribution of the
software without specific, written prior permission.
The author disclaim all warranties with regard to this
software, including all implied warranties of merchantability
and fitness. In no event shall the author be liable for any
special, indirect or consequential damages or any damages
whatsoever resulting from loss of use, data or profits, whether
in an action of contract, negligence or other tortious action,
arising out of or in connection with the use or performance of
this software.
*/
/** \file
*
* Header file for Magstripe.c.
*/
#ifndef _MAGSTRIPE_H_
#define _MAGSTRIPE_H_
/* Includes: */
#include <avr/io.h>
#include <avr/wdt.h>
#include <avr/interrupt.h>
#include <stdbool.h>
#include <string.h>
#include "Descriptors.h"
#include "MagstripeHW.h"
#include "CircularBitBuffer.h"
#include <LUFA/Version.h> // Library Version Information
#include <LUFA/Common/ButtLoadTag.h> // PROGMEM tags readable by the ButtLoad project
#include <LUFA/Drivers/USB/USB.h> // USB Functionality
#include <LUFA/Scheduler/Scheduler.h> // Simple scheduler for task management
/* Task Definitions: */
/** Task definition for the keyboard and magnetic card reading task. */
TASK(USB_Keyboard_Report);
TASK(Magstripe_Read);
/* Macros: */
/** HID Class Specific Request to get the current HID report from the device. */
#define REQ_GetReport 0x01
/** HID Class Specific Request to get the current device idle count. */
#define REQ_GetIdle 0x02
/** HID Class Specific Request to set the current HID report to the device. */
#define REQ_SetReport 0x09
/** HID Class Specific Request to set the device's idle count. */
#define REQ_SetIdle 0x0A
/** HID Class Specific Request to get the current HID report protocol mode. */
#define REQ_GetProtocol 0x03
/** HID Class Specific Request to set the current HID report protocol mode. */
#define REQ_SetProtocol 0x0B
/** HID keyboard keycode to indicate that the "1" key is currently pressed. */
#define KEY_1 30
/** HID keyboard keycode to indicate that the "0" key is currently pressed. */
#define KEY_0 39
/** HID keyboard keycode to indicate that the enter key is currently pressed. */
#define KEY_ENTER 40
/* Type Defines: */
/** Type define for the keyboard report structure. This structure matches the report layout
* given to the host in the HID Report descriptor, as well as matches the boot protocol report
* structure. This means that this one report structure can be used in both Report and Boot Protocol
* modes. */
typedef struct
{
uint8_t Modifier; /**< Modifier byte, indicating pressed modifier keys such as CTRL or ALT */
uint8_t Reserved; /**< Reserved for OEM use, always set to 0 */
uint8_t KeyCode[6]; /**< Key code array for pressed keys - up to six can be given simultaneously */
} USB_KeyboardReport_Data_t;
/* Event Handlers: */
/** Indicates that this module will catch the USB_Connect event when thrown by the library. */
HANDLES_EVENT(USB_Connect);
/** Indicates that this module will catch the USB_Disconnect event when thrown by the library. */
HANDLES_EVENT(USB_Disconnect);
/** Indicates that this module will catch the USB_ConfigurationChanged event when thrown by the library. */
HANDLES_EVENT(USB_ConfigurationChanged);
/** Indicates that this module will catch the USB_UnhandledControlPacket event when thrown by the library. */
HANDLES_EVENT(USB_UnhandledControlPacket);
/* Function Prototypes: */
bool GetNextReport(USB_KeyboardReport_Data_t* ReportData);
void SendKey(USB_KeyboardReport_Data_t* KeyboardReportData, uint8_t Key);
void Send(USB_KeyboardReport_Data_t* KeyboardReportData, bool SendReport);
#endif

@ -0,0 +1,85 @@
/** \file
*
* This file contains special DoxyGen information for the generation of the main page and other special
* documentation pages. It is not a project source file.
*/
/** \mainpage Denver Gingerich's USBSnoop Magnetic Card Reader Project
*
* Firmware for a USB AVR powered USB TTL magnetic stripe reader (using a card
* reader such as the Omron V3B-4K) by Denver Gingerich. This project is designed
* to be used with the open source Stripe Snoop project at http://stripesnoop.sourceforge.net/.
*
* See http://ossguy.com/ss_usb/ for the USB reader hardware project website,
* including construction and support details.
*
* To use, connect your magentic card reader device to the USB AVR as follows (pin and port mapping may be adjusted
* from the project makefile):
*
* <table>
* <tr>
* <td><b>Signal:</b></td>
* <td><b>AVR Port:</b></td>
* </tr>
* <tr>
* <td>Track 1 Data</td>
* <td>PORTC, Pin 1</td>
* </tr>
* <tr>
* <td>Track 1 Clock</td>
* <td>PORTC, Pin 2</td>
* </tr>
* <tr>
* <td>Track 2 Data</td>
* <td>PORTC, Pin 3</td>
* </tr>
* <tr>
* <td>Track 2 Clock</td>
* <td>PORTC, Pin 0</td>
* </tr>
* <tr>
* <td>Track 3 Data</td>
* <td>PORTC, Pin 5</td>
* </tr>
* <tr>
* <td>Track 3 Clock</td>
* <td>PORTC, Pin 6</td>
* </tr>
* <tr>
* <td>Card Detect</td>
* <td>PORTC, Pin 4</td>
* </tr>
* </table>
*
*
* This project is based on the LUFA Keyboard demonstration application,
* written by Denver Gingerich.
*
* This application uses a keyboard HID driver to communicate the data collected
* a TTL magnetic stripe reader to the connected computer. The raw bitstream
* obtained from the magnetic stripe reader is "typed" through the keyboard
* driver as 0's and 1's. After every card swipe, the demo will send a return key.
*
* <table>
* <tr>
* <td><b>USB Mode:</b></td>
* <td>Device</td>
* </tr>
* <tr>
* <td><b>USB Class:</b></td>
* <td>Human Interface Device (HID)</td>
* </tr>
* <tr>
* <td><b>USB Subclass:</b></td>
* <td>Keyboard</td>
* </tr>
* <tr>
* <td><b>Relevant Standards:</b></td>
* <td>USBIF HID Standard, USBIF HID Usage Tables</td>
* </tr>
* <tr>
* <td><b>Usable Speeds:</b></td>
* <td>Low Speed Mode, Full Speed Mode</td>
* </tr>
* </table>
*/

@ -0,0 +1,100 @@
/*
Copyright 2009 Denver Gingerich (denver [at] ossguy [dot] com)
Copyright 2009 Dean Camera (dean [at] fourwalledcubicle [dot] com)
Permission to use, copy, modify, and distribute this software
and its documentation for any purpose and without fee is hereby
granted, provided that the above copyright notice appear in all
copies and that both that the copyright notice and this
permission notice and warranty disclaimer appear in supporting
documentation, and that the name of the author not be used in
advertising or publicity pertaining to distribution of the
software without specific, written prior permission.
The author disclaim all warranties with regard to this
software, including all implied warranties of merchantability
and fitness. In no event shall the author be liable for any
special, indirect or consequential damages or any damages
whatsoever resulting from loss of use, data or profits, whether
in an action of contract, negligence or other tortious action,
arising out of or in connection with the use or performance of
this software.
*/
/*
NOTE: The user of this include file MUST define the following macros
prior to including the file:
MAG_T1_CLOCK_PIN Pin connected to Track 1 clock wire (ie. PORTC1)
MAG_T1_DATA_PIN Pin connected to Track 1 data wire (ie. PORTC2)
MAG_T2_CLOCK_PIN Pin connected to Track 2 clock wire (ie. PORTC3)
MAG_T2_DATA_PIN Pin connected to Track 2 data wire (ie. PORTC0)
MAG_T3_CLOCK_PIN Pin connected to Track 3 clock wire (ie. PORTC5)
MAG_T3_DATA_PIN Pin connected to Track 3 data wire (ie. PORTC6)
MAG_CLS_PIN Pin connected to card loaded wire (ie. PORTC4)
MAG_PIN PIN macro for the reader's port (ie. PINC)
MAG_DDR DDR macro for the reader's port (ie. DDRC)
MAG_PORT PORT macro for the reader's port (ie. PORTC)
The example macros listed above assume that the Track 2 data wire is
connected to pin 0 on port C, the Track 2 clock wire is connected to
pin 3 on port C (similarly for Tracks 1 and 3), and the card loaded
wire is connected to pin 4 on port C.
If the magstripe reader you are using only reads one or two tracks,
then set the clock and data pins for the tracks it doesn't read to a
pin that is unused. For example, on the AT90USBKey, any of the pins on
port C that do not have wires attached will be unused since they are
not connected to any onboard devices (such as the joystick or
temperature sensor).
Connecting wires to pins on different ports (ie. a data wire to pin 0
on port C and a clock wire to pin 0 on port D) is currently
unsupported. All pins specified above must be on the same port.
*/
/** \file
*
* Driver header for a TTL Magnetic Card reader device (such as the Omron V3B-4K).
*/
#ifndef _MAGSTRIPEHW_H_
#define _MAGSTRIPEHW_H_
/* Includes: */
#include <avr/io.h>
#include <LUFA/Common/Common.h>
/* Private Interface - For use in library only: */
/* Macros: */
/** Mask of the track data, clock and card detection pins. */
#define MAG_MASK (MAG_T1_DATA | MAG_T1_CLOCK | \
MAG_T2_DATA | MAG_T2_CLOCK | \
MAG_T3_DATA | MAG_T3_CLOCK | \
MAG_CARDPRESENT)
/* Public Interface - May be used in end-application: */
/* Inline Functions: */
/** Initializes the magnetic stripe card reader ports and pins so that the card reader
* device can be controlled and read by the card reader driver. This must be called before
* trying to read any of the card reader's status lines.
*/
static inline void Magstripe_Init(void)
{
MAG_DDR &= ~MAG_MASK;
MAG_PORT |= MAG_MASK;
};
/** Returns the status of all the magnetic card reader's outputs.
*
* \return A mask indicating which card lines are high or low
*/
static inline uint8_t Magstripe_GetStatus(void) ATTR_WARN_UNUSED_RESULT;
static inline uint8_t Magstripe_GetStatus(void)
{
/* Magstripe IOs are active low and must be inverted when read */
return ((uint8_t)~MAG_PIN & MAG_MASK);
}
#endif

@ -0,0 +1,712 @@
# Hey Emacs, this is a -*- makefile -*-
#----------------------------------------------------------------------------
# WinAVR Makefile Template written by Eric B. Weddington, Jörg Wunsch, et al.
# >> Modified for use with the LUFA project. <<
#
# Released to the Public Domain
#
# Additional material for this makefile was written by:
# Peter Fleury
# Tim Henigan
# Colin O'Flynn
# Reiner Patommel
# Markus Pfaff
# Sander Pool
# Frederik Rouleau
# Carlos Lamas
# Dean Camera
# Opendous Inc.
# Denver Gingerich
#
#----------------------------------------------------------------------------
# On command line:
#
# make all = Make software.
#
# make clean = Clean out built project files.
#
# make coff = Convert ELF to AVR COFF.
#
# make extcoff = Convert ELF to AVR Extended COFF.
#
# make program = Download the hex file to the device, using avrdude.
# Please customize the avrdude settings below first!
#
# make dfu = Download the hex file to the device, using dfu-programmer (must
# have dfu-programmer installed).
#
# make flip = Download the hex file to the device, using Atmel FLIP (must
# have Atmel FLIP installed).
#
# make dfu-ee = Download the eeprom file to the device, using dfu-programmer
# (must have dfu-programmer installed).
#
# make flip-ee = Download the eeprom file to the device, using Atmel FLIP
# (must have Atmel FLIP installed).
#
# make doxygen = Generate DoxyGen documentation for the project (must have
# DoxyGen installed)
#
# make debug = Start either simulavr or avarice as specified for debugging,
# with avr-gdb or avr-insight as the front end for debugging.
#
# make filename.s = Just compile filename.c into the assembler code only.
#
# make filename.i = Create a preprocessed source file for use in submitting
# bug reports to the GCC project.
#
# To rebuild project do "make clean" then "make all".
#----------------------------------------------------------------------------
# MCU name
MCU = at90usb1287
# Target board (see library BoardTypes.h documentation, USER or blank for projects not requiring
# LUFA board drivers). If USER is selected, put custom board drivers in a directory called
# "Board" inside the application directory.
BOARD = USBKEY
# Processor frequency.
# This will define a symbol, F_CPU, in all source code files equal to the
# processor frequency. You can then use this symbol in your source code to
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
# automatically to create a 32-bit value in your source code.
# Typical values are:
# F_CPU = 1000000
# F_CPU = 1843200
# F_CPU = 2000000
# F_CPU = 3686400
# F_CPU = 4000000
# F_CPU = 7372800
# F_CPU = 8000000
# F_CPU = 11059200
# F_CPU = 14745600
# F_CPU = 16000000
# F_CPU = 18432000
# F_CPU = 20000000
F_CPU = 16000000
# Output format. (can be srec, ihex, binary)
FORMAT = ihex
# Target file name (without extension).
TARGET = Magstripe
# Object files directory
# To put object files in current directory, use a dot (.), do NOT make
# this an empty or blank macro!
OBJDIR = .
# List C source files here. (C dependencies are automatically generated.)
SRC = $(TARGET).c \
Descriptors.c \
CircularBitBuffer.c \
../../LUFA/Scheduler/Scheduler.c \
../../LUFA/Drivers/USB/LowLevel/LowLevel.c \
../../LUFA/Drivers/USB/LowLevel/Endpoint.c \
../../LUFA/Drivers/USB/LowLevel/DevChapter9.c \
../../LUFA/Drivers/USB/HighLevel/USBTask.c \
../../LUFA/Drivers/USB/HighLevel/USBInterrupt.c \
../../LUFA/Drivers/USB/HighLevel/Events.c \
../../LUFA/Drivers/USB/HighLevel/StdDescriptors.c \
# List C++ source files here. (C dependencies are automatically generated.)
CPPSRC =
# List Assembler source files here.
# Make them always end in a capital .S. Files ending in a lowercase .s
# will not be considered source files but generated files (assembler
# output from the compiler), and will be deleted upon "make clean"!
# Even though the DOS/Win* filesystem matches both .s and .S the same,
# it will preserve the spelling of the filenames, and gcc itself does
# care about how the name is spelled on its command-line.
ASRC =
# Optimization level, can be [0, 1, 2, 3, s].
# 0 = turn off optimization. s = optimize for size.
# (Note: 3 is not always the best optimization level. See avr-libc FAQ.)
OPT = s
# Debugging format.
# Native formats for AVR-GCC's -g are dwarf-2 [default] or stabs.
# AVR Studio 4.10 requires dwarf-2.
# AVR [Extended] COFF format requires stabs, plus an avr-objcopy run.
DEBUG = dwarf-2
# List any extra directories to look for include files here.
# Each directory must be seperated by a space.
# Use forward slashes for directory separators.
# For a directory that has spaces, enclose it in quotes.
EXTRAINCDIRS = ../../
# Compiler flag to set the C Standard level.
# c89 = "ANSI" C
# gnu89 = c89 plus GCC extensions
# c99 = ISO C99 standard (not yet fully implemented)
# gnu99 = c99 plus GCC extensions
CSTANDARD = -std=gnu99
# Place -D or -U options here for C sources
CDEFS = -DF_CPU=$(F_CPU)UL -DBOARD=BOARD_$(BOARD) -DUSE_NONSTANDARD_DESCRIPTOR_NAMES -DNO_STREAM_CALLBACKS
CDEFS += -DUSB_DEVICE_ONLY -DUSE_STATIC_OPTIONS="(USB_DEVICE_OPT_FULLSPEED | USB_OPT_REG_ENABLED | USB_OPT_AUTO_PLL)"
CDEFS += -DMAG_T1_CLOCK="(1 << 0)"
CDEFS += -DMAG_T1_DATA="(1 << 1)"
CDEFS += -DMAG_T2_CLOCK="(1 << 2)"
CDEFS += -DMAG_T2_DATA="(1 << 3)"
CDEFS += -DMAG_T3_CLOCK="(1 << 4)"
CDEFS += -DMAG_T3_DATA="(1 << 5)"
CDEFS += -DMAG_CARDPRESENT="(1 << 6)"
CDEFS += -DMAG_PIN=PINB
CDEFS += -DMAG_DDR=DDRB
CDEFS += -DMAG_PORT=PORTB
# Place -D or -U options here for ASM sources
ADEFS = -DF_CPU=$(F_CPU)
# Place -D or -U options here for C++ sources
CPPDEFS = -DF_CPU=$(F_CPU)UL
#CPPDEFS += -D__STDC_LIMIT_MACROS
#CPPDEFS += -D__STDC_CONSTANT_MACROS
#---------------- Compiler Options C ----------------
# -g*: generate debugging information
# -O*: optimization level
# -f...: tuning, see GCC manual and avr-libc documentation
# -Wall...: warning level
# -Wa,...: tell GCC to pass this to the assembler.
# -adhlns...: create assembler listing
CFLAGS = -g$(DEBUG)
CFLAGS += $(CDEFS)
CFLAGS += -O$(OPT)
CFLAGS += -funsigned-char
CFLAGS += -funsigned-bitfields
CFLAGS += -fpack-struct
CFLAGS += -fshort-enums
CFLAGS += -ffunction-sections
CFLAGS += -finline-limit=20
CFLAGS += -Wall
CFLAGS += -Wstrict-prototypes
CFLAGS += -Wundef
#CFLAGS += -fno-unit-at-a-time
#CFLAGS += -Wunreachable-code
#CFLAGS += -Wsign-compare
CFLAGS += -Wa,-adhlns=$(<:%.c=$(OBJDIR)/%.lst)
CFLAGS += $(patsubst %,-I%,$(EXTRAINCDIRS))
CFLAGS += $(CSTANDARD)
#---------------- Compiler Options C++ ----------------
# -g*: generate debugging information
# -O*: optimization level
# -f...: tuning, see GCC manual and avr-libc documentation
# -Wall...: warning level
# -Wa,...: tell GCC to pass this to the assembler.
# -adhlns...: create assembler listing
CPPFLAGS = -g$(DEBUG)
CPPFLAGS += $(CPPDEFS)
CPPFLAGS += -O$(OPT)
CPPFLAGS += -funsigned-char
CPPFLAGS += -funsigned-bitfields
CPPFLAGS += -fpack-struct
CPPFLAGS += -fshort-enums
CPPFLAGS += -fno-exceptions
CPPFLAGS += -Wall
CFLAGS += -Wundef
#CPPFLAGS += -fno-unit-at-a-time
#CPPFLAGS += -Wstrict-prototypes
#CPPFLAGS += -Wunreachable-code
#CPPFLAGS += -Wsign-compare
CPPFLAGS += -Wa,-adhlns=$(<:%.cpp=$(OBJDIR)/%.lst)
CPPFLAGS += $(patsubst %,-I%,$(EXTRAINCDIRS))
#CPPFLAGS += $(CSTANDARD)
#---------------- Assembler Options ----------------
# -Wa,...: tell GCC to pass this to the assembler.
# -adhlns: create listing
# -gstabs: have the assembler create line number information; note that
# for use in COFF files, additional information about filenames
# and function names needs to be present in the assembler source
# files -- see avr-libc docs [FIXME: not yet described there]
# -listing-cont-lines: Sets the maximum number of continuation lines of hex
# dump that will be displayed for a given single line of source input.
ASFLAGS = $(ADEFS) -Wa,-adhlns=$(<:%.S=$(OBJDIR)/%.lst),-gstabs,--listing-cont-lines=100
#---------------- Library Options ----------------
# Minimalistic printf version
PRINTF_LIB_MIN = -Wl,-u,vfprintf -lprintf_min
# Floating point printf version (requires MATH_LIB = -lm below)
PRINTF_LIB_FLOAT = -Wl,-u,vfprintf -lprintf_flt
# If this is left blank, then it will use the Standard printf version.
PRINTF_LIB =
#PRINTF_LIB = $(PRINTF_LIB_MIN)
#PRINTF_LIB = $(PRINTF_LIB_FLOAT)
# Minimalistic scanf version
SCANF_LIB_MIN = -Wl,-u,vfscanf -lscanf_min
# Floating point + %[ scanf version (requires MATH_LIB = -lm below)
SCANF_LIB_FLOAT = -Wl,-u,vfscanf -lscanf_flt
# If this is left blank, then it will use the Standard scanf version.
SCANF_LIB =
#SCANF_LIB = $(SCANF_LIB_MIN)
#SCANF_LIB = $(SCANF_LIB_FLOAT)
MATH_LIB = -lm
# List any extra directories to look for libraries here.
# Each directory must be seperated by a space.
# Use forward slashes for directory separators.
# For a directory that has spaces, enclose it in quotes.
EXTRALIBDIRS =
#---------------- External Memory Options ----------------
# 64 KB of external RAM, starting after internal RAM (ATmega128!),
# used for variables (.data/.bss) and heap (malloc()).
#EXTMEMOPTS = -Wl,-Tdata=0x801100,--defsym=__heap_end=0x80ffff
# 64 KB of external RAM, starting after internal RAM (ATmega128!),
# only used for heap (malloc()).
#EXTMEMOPTS = -Wl,--section-start,.data=0x801100,--defsym=__heap_end=0x80ffff
EXTMEMOPTS =
#---------------- Linker Options ----------------
# -Wl,...: tell GCC to pass this to linker.
# -Map: create map file
# --cref: add cross reference to map file
LDFLAGS = -Wl,-Map=$(TARGET).map,--cref
LDFLAGS += -Wl,--relax
LDFLAGS += -Wl,--gc-sections
LDFLAGS += $(EXTMEMOPTS)
LDFLAGS += $(patsubst %,-L%,$(EXTRALIBDIRS))
LDFLAGS += $(PRINTF_LIB) $(SCANF_LIB) $(MATH_LIB)
#LDFLAGS += -T linker_script.x
#---------------- Programming Options (avrdude) ----------------
# Programming hardware: alf avr910 avrisp bascom bsd
# dt006 pavr picoweb pony-stk200 sp12 stk200 stk500
#
# Type: avrdude -c ?
# to get a full listing.
#
AVRDUDE_PROGRAMMER = jtagmkII
# com1 = serial port. Use lpt1 to connect to parallel port.
AVRDUDE_PORT = usb
AVRDUDE_WRITE_FLASH = -U flash:w:$(TARGET).hex
#AVRDUDE_WRITE_EEPROM = -U eeprom:w:$(TARGET).eep
# Uncomment the following if you want avrdude's erase cycle counter.
# Note that this counter needs to be initialized first using -Yn,
# see avrdude manual.
#AVRDUDE_ERASE_COUNTER = -y
# Uncomment the following if you do /not/ wish a verification to be
# performed after programming the device.
#AVRDUDE_NO_VERIFY = -V
# Increase verbosity level. Please use this when submitting bug
# reports about avrdude. See <http://savannah.nongnu.org/projects/avrdude>
# to submit bug reports.
#AVRDUDE_VERBOSE = -v -v
AVRDUDE_FLAGS = -p $(MCU) -P $(AVRDUDE_PORT) -c $(AVRDUDE_PROGRAMMER)
AVRDUDE_FLAGS += $(AVRDUDE_NO_VERIFY)
AVRDUDE_FLAGS += $(AVRDUDE_VERBOSE)
AVRDUDE_FLAGS += $(AVRDUDE_ERASE_COUNTER)
#---------------- Debugging Options ----------------
# For simulavr only - target MCU frequency.
DEBUG_MFREQ = $(F_CPU)
# Set the DEBUG_UI to either gdb or insight.
# DEBUG_UI = gdb
DEBUG_UI = insight
# Set the debugging back-end to either avarice, simulavr.
DEBUG_BACKEND = avarice
#DEBUG_BACKEND = simulavr
# GDB Init Filename.
GDBINIT_FILE = __avr_gdbinit
# When using avarice settings for the JTAG
JTAG_DEV = /dev/com1
# Debugging port used to communicate between GDB / avarice / simulavr.
DEBUG_PORT = 4242
# Debugging host used to communicate between GDB / avarice / simulavr, normally
# just set to localhost unless doing some sort of crazy debugging when
# avarice is running on a different computer.
DEBUG_HOST = localhost
#============================================================================
# Define programs and commands.
SHELL = sh
CC = avr-gcc
OBJCOPY = avr-objcopy
OBJDUMP = avr-objdump
SIZE = avr-size
AR = avr-ar rcs
NM = avr-nm
AVRDUDE = avrdude
REMOVE = rm -f
REMOVEDIR = rm -rf
COPY = cp
WINSHELL = cmd
# Define Messages
# English
MSG_ERRORS_NONE = Errors: none
MSG_BEGIN = -------- begin --------
MSG_END = -------- end --------
MSG_SIZE_BEFORE = Size before:
MSG_SIZE_AFTER = Size after:
MSG_COFF = Converting to AVR COFF:
MSG_EXTENDED_COFF = Converting to AVR Extended COFF:
MSG_FLASH = Creating load file for Flash:
MSG_EEPROM = Creating load file for EEPROM:
MSG_EXTENDED_LISTING = Creating Extended Listing:
MSG_SYMBOL_TABLE = Creating Symbol Table:
MSG_LINKING = Linking:
MSG_COMPILING = Compiling C:
MSG_COMPILING_CPP = Compiling C++:
MSG_ASSEMBLING = Assembling:
MSG_CLEANING = Cleaning project:
MSG_CREATING_LIBRARY = Creating library:
# Define all object files.
OBJ = $(SRC:%.c=$(OBJDIR)/%.o) $(CPPSRC:%.cpp=$(OBJDIR)/%.o) $(ASRC:%.S=$(OBJDIR)/%.o)
# Define all listing files.
LST = $(SRC:%.c=$(OBJDIR)/%.lst) $(CPPSRC:%.cpp=$(OBJDIR)/%.lst) $(ASRC:%.S=$(OBJDIR)/%.lst)
# Compiler flags to generate dependency files.
GENDEPFLAGS = -MMD -MP -MF .dep/$(@F).d
# Combine all necessary flags and optional flags.
# Add target processor to flags.
ALL_CFLAGS = -mmcu=$(MCU) -I. $(CFLAGS) $(GENDEPFLAGS)
ALL_CPPFLAGS = -mmcu=$(MCU) -I. -x c++ $(CPPFLAGS) $(GENDEPFLAGS)
ALL_ASFLAGS = -mmcu=$(MCU) -I. -x assembler-with-cpp $(ASFLAGS)
# Default target.
all: begin gccversion sizebefore build checkhooks checklibmode sizeafter end
# Change the build target to build a HEX file or a library.
build: elf hex eep lss sym
#build: lib
elf: $(TARGET).elf
hex: $(TARGET).hex
eep: $(TARGET).eep
lss: $(TARGET).lss
sym: $(TARGET).sym
LIBNAME=lib$(TARGET).a
lib: $(LIBNAME)
# Eye candy.
# AVR Studio 3.x does not check make's exit code but relies on
# the following magic strings to be generated by the compile job.
begin:
@echo
@echo $(MSG_BEGIN)
end:
@echo $(MSG_END)
@echo
# Display size of file.
HEXSIZE = $(SIZE) --target=$(FORMAT) $(TARGET).hex
ELFSIZE = $(SIZE) $(MCU_FLAG) $(FORMAT_FLAG) $(TARGET).elf
MCU_FLAG = $(shell $(SIZE) --help | grep -- --mcu > /dev/null && echo --mcu=$(MCU) )
FORMAT_FLAG = $(shell $(SIZE) --help | grep -- --format=.*avr > /dev/null && echo --format=avr )
sizebefore:
@if test -f $(TARGET).elf; then echo; echo $(MSG_SIZE_BEFORE); $(ELFSIZE); \
2>/dev/null; echo; fi
sizeafter:
@if test -f $(TARGET).elf; then echo; echo $(MSG_SIZE_AFTER); $(ELFSIZE); \
2>/dev/null; echo; fi
checkhooks: build
@echo
@echo ------- Unhooked LUFA Events -------
@$(shell) (grep -s '^Event.*LUFA/.*\\.o' $(TARGET).map | \
cut -d' ' -f1 | cut -d'_' -f2- | grep ".*") || \
echo "(None)"
@echo ----- End Unhooked LUFA Events -----
checklibmode:
@echo
@echo ----------- Library Mode -----------
@$(shell) ($(CC) $(ALL_CFLAGS) -E -dM - < /dev/null \
| grep 'USB_\(DEVICE\|HOST\)_ONLY' | cut -d' ' -f2 | grep ".*") \
|| echo "No specific mode (both device and host mode allowable)."
@echo ------------------------------------
# Display compiler version information.
gccversion :
@$(CC) --version
# Program the device.
program: $(TARGET).hex $(TARGET).eep
$(AVRDUDE) $(AVRDUDE_FLAGS) $(AVRDUDE_WRITE_FLASH) $(AVRDUDE_WRITE_EEPROM)
flip: $(TARGET).hex
batchisp -hardware usb -device $(MCU) -operation erase f
batchisp -hardware usb -device $(MCU) -operation loadbuffer $(TARGET).hex program
batchisp -hardware usb -device $(MCU) -operation start reset 0
dfu: $(TARGET).hex
dfu-programmer $(MCU) erase
dfu-programmer $(MCU) flash --debug 1 $(TARGET).hex
dfu-programmer $(MCU) reset
flip-ee: $(TARGET).hex $(TARGET).eep
copy $(TARGET).eep $(TARGET)eep.hex
batchisp -hardware usb -device $(MCU) -operation memory EEPROM erase
batchisp -hardware usb -device $(MCU) -operation memory EEPROM loadbuffer $(TARGET)eep.hex program
batchisp -hardware usb -device $(MCU) -operation start reset 0
dfu-ee: $(TARGET).hex $(TARGET).eep
dfu-programmer $(MCU) erase
dfu-programmer $(MCU) eeprom --debug 1 $(TARGET).eep
dfu-programmer $(MCU) reset
# Generate avr-gdb config/init file which does the following:
# define the reset signal, load the target file, connect to target, and set
# a breakpoint at main().
gdb-config:
@$(REMOVE) $(GDBINIT_FILE)
@echo define reset >> $(GDBINIT_FILE)
@echo SIGNAL SIGHUP >> $(GDBINIT_FILE)
@echo end >> $(GDBINIT_FILE)
@echo file $(TARGET).elf >> $(GDBINIT_FILE)
@echo target remote $(DEBUG_HOST):$(DEBUG_PORT) >> $(GDBINIT_FILE)
ifeq ($(DEBUG_BACKEND),simulavr)
@echo load >> $(GDBINIT_FILE)
endif
@echo break main >> $(GDBINIT_FILE)
debug: gdb-config $(TARGET).elf
ifeq ($(DEBUG_BACKEND), avarice)
@echo Starting AVaRICE - Press enter when "waiting to connect" message displays.
@$(WINSHELL) /c start avarice --jtag $(JTAG_DEV) --erase --program --file \
$(TARGET).elf $(DEBUG_HOST):$(DEBUG_PORT)
@$(WINSHELL) /c pause
else
@$(WINSHELL) /c start simulavr --gdbserver --device $(MCU) --clock-freq \
$(DEBUG_MFREQ) --port $(DEBUG_PORT)
endif
@$(WINSHELL) /c start avr-$(DEBUG_UI) --command=$(GDBINIT_FILE)
# Convert ELF to COFF for use in debugging / simulating in AVR Studio or VMLAB.
COFFCONVERT = $(OBJCOPY) --debugging
COFFCONVERT += --change-section-address .data-0x800000
COFFCONVERT += --change-section-address .bss-0x800000
COFFCONVERT += --change-section-address .noinit-0x800000
COFFCONVERT += --change-section-address .eeprom-0x810000
coff: $(TARGET).elf
@echo
@echo $(MSG_COFF) $(TARGET).cof
$(COFFCONVERT) -O coff-avr $< $(TARGET).cof
extcoff: $(TARGET).elf
@echo
@echo $(MSG_EXTENDED_COFF) $(TARGET).cof
$(COFFCONVERT) -O coff-ext-avr $< $(TARGET).cof
# Create final output files (.hex, .eep) from ELF output file.
%.hex: %.elf
@echo
@echo $(MSG_FLASH) $@
$(OBJCOPY) -O $(FORMAT) -R .eeprom $< $@
%.eep: %.elf
@echo
@echo $(MSG_EEPROM) $@
-$(OBJCOPY) -j .eeprom --set-section-flags=.eeprom="alloc,load" \
--change-section-lma .eeprom=0 --no-change-warnings -O $(FORMAT) $< $@ || exit 0
# Create extended listing file from ELF output file.
%.lss: %.elf
@echo
@echo $(MSG_EXTENDED_LISTING) $@
$(OBJDUMP) -h -z -S $< > $@
# Create a symbol table from ELF output file.
%.sym: %.elf
@echo
@echo $(MSG_SYMBOL_TABLE) $@
$(NM) -n $< > $@
# Create library from object files.
.SECONDARY : $(TARGET).a
.PRECIOUS : $(OBJ)
%.a: $(OBJ)
@echo
@echo $(MSG_CREATING_LIBRARY) $@
$(AR) $@ $(OBJ)
# Link: create ELF output file from object files.
.SECONDARY : $(TARGET).elf
.PRECIOUS : $(OBJ)
%.elf: $(OBJ)
@echo
@echo $(MSG_LINKING) $@
$(CC) $(ALL_CFLAGS) $^ --output $@ $(LDFLAGS)
# Compile: create object files from C source files.
$(OBJDIR)/%.o : %.c
@echo
@echo $(MSG_COMPILING) $<
$(CC) -c $(ALL_CFLAGS) $< -o $@
# Compile: create object files from C++ source files.
$(OBJDIR)/%.o : %.cpp
@echo
@echo $(MSG_COMPILING_CPP) $<
$(CC) -c $(ALL_CPPFLAGS) $< -o $@
# Compile: create assembler files from C source files.
%.s : %.c
$(CC) -S $(ALL_CFLAGS) $< -o $@
# Compile: create assembler files from C++ source files.
%.s : %.cpp
$(CC) -S $(ALL_CPPFLAGS) $< -o $@
# Assemble: create object files from assembler source files.
$(OBJDIR)/%.o : %.S
@echo
@echo $(MSG_ASSEMBLING) $<
$(CC) -c $(ALL_ASFLAGS) $< -o $@
# Create preprocessed source for use in sending a bug report.
%.i : %.c
$(CC) -E -mmcu=$(MCU) -I. $(CFLAGS) $< -o $@
# Target: clean project.
clean: begin clean_list clean_binary end
clean_binary:
$(REMOVE) $(TARGET).hex
clean_list:
@echo $(MSG_CLEANING)
$(REMOVE) $(TARGET).eep
$(REMOVE) $(TARGET).cof
$(REMOVE) $(TARGET).elf
$(REMOVE) $(TARGET).map
$(REMOVE) $(TARGET).sym
$(REMOVE) $(TARGET).lss
$(REMOVE) $(SRC:%.c=$(OBJDIR)/%.o)
$(REMOVE) $(SRC:%.c=$(OBJDIR)/%.lst)
$(REMOVE) $(SRC:.c=.s)
$(REMOVE) $(SRC:.c=.d)
$(REMOVE) $(SRC:.c=.i)
$(REMOVEDIR) .dep
doxygen:
@echo Generating Project Documentation...
@doxygen Doxygen.conf
@echo Documentation Generation Complete.
clean_doxygen:
rm -rf Documentation
# Create object files directory
$(shell mkdir $(OBJDIR) 2>/dev/null)
# Include the dependency files.
-include $(shell mkdir .dep 2>/dev/null) $(wildcard .dep/*)
# Listing of phony targets.
.PHONY : all checkhooks checklibmode begin \
finish end sizebefore sizeafter gccversion \
build elf hex eep lss sym coff extcoff \
clean clean_list clean_binary program debug \
gdb-config doxygen dfu flip

@ -0,0 +1,25 @@
#
# LUFA Library
# Copyright (C) Dean Camera, 2009.
#
# dean [at] fourwalledcubicle [dot] com
# www.fourwalledcubicle.com
#
# Makefile to build all the LUFA Projects. Call with "make all" to
# rebuild all projects.
# Projects are pre-cleaned before each one is built, to ensure any
# custom LUFA library build options are reflected in the compiled
# code.
all:
make -C Magstripe clean
make -C Magstripe all
make -C AVRISP_Programmer clean
make -C AVRISP_Programmer all
%:
make -C Magstripe $@
make -C AVRISP_Programmer $@
Loading…
Cancel
Save