QMK keymaps are defined inside a C source file. The data structure is an array of arrays. The outer array is a list of layer arrays while the inner layer array is a list of keys. Most keyboards define a `KEYMAP()` macro to help you create this array of arrays.
QMK keymaps are defined inside a C source file. The data structure is an array of arrays. The outer array is a list of layer arrays while the inner layer array is a list of keys. Most keyboards define a `KEYMAP()` macro to help you create this array of arrays.
## Keymap and layers
In QMK, **`const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS]`** holds multiple **layers** of keymap information in **16 bit** data holding the **action code**. You can define **32 layers** at most.
For trivial key definitions, the higher 8 bits of the **action code** are all 0 and the lower 8 bits holds the USB HID usage code generated by the key as **keycode**.
Respective layers can be validated simultaneously. Layers are indexed with 0 to 31 and higher layer has precedence.
Keymap: 32 Layers Layer: action code matrix
----------------- ---------------------
stack of layers array_of_action_code[row][column]
____________ precedence _______________________
/ / | high / ESC / F1 / F2 / F3 ....
31 /___________// | /-----/-----/-----/-----
30 /___________// | / TAB / Q / W / E ....
29 /___________/ | /-----/-----/-----/-----
: _:_:_:_:_:__ | : /LCtrl/ A / S / D ....
: / : : : : : / | : / : : : :
2 /___________// | 2 `--------------------------
1 /___________// | 1 `--------------------------
0 /___________/ V low 0 `--------------------------
Sometimes, the action code stored in keymap may be referred as keycode in some documents due to the TMK history.
### Keymap layer status
Keymap layer has its state in two 32 bit parameters:
* **`default_layer_state`** indicates a base keymap layer(0-31) which is always valid and to be referred.
* **`layer_state`** () has current on/off status of the layer on its each bit.
Keymap has its state in two parameter **`default_layer`** indicates a base keymap layer(0-31) which is always valid and to be referred, **`keymap_stat`** is 16bit variable which has current on/off status of layers on its each bit.
Keymap layer '0' is usually `default_layer` and which is the only valid layer and other layers is initially off after boot up firmware, though, you can configured them in `config.h`.
To change `default_layer` will be useful when you switch key layout completely, say you want Colmak instead of Qwerty.
Initial state of Keymap Change base layout
----------------------- ------------------
31 31
30 30
29 29
: :
: : ____________
2 ____________ 2 / /
1 / / ,->1 /___________/
,->0 /___________/ | 0
| |
`--- default_layer = 0 `--- default_layer = 1
layer_state = 0x00000001 layer_state = 0x00000002
On the other hand, you shall change `layer_state` to overlay base layer with some layers for feature such as navigation keys, function key(F1-F12), media keys or special actions.
Overlay feature layer
--------------------- bit|status
____________ ---+------
31 / / 31 | 0
30 /___________// -----> 30 | 1
29 /___________/ -----> 29 | 1
: : | :
: ____________ : | :
2 / / 2 | 0
,->1 /___________/ -----> 1 | 1
| 0 0 | 0
| +
`--- default_layer = 1 |
layer_state = 0x60000002 <-'
### Layer Precedence and Transparency
Note that ***higher layer has higher priority on stack of layers***, namely firmware falls down from top layer to bottom to look up keycode. Once it spots keycode other than **`KC_TRNS`**(transparent) on a layer it stops searching and lower layers aren't referred.
You can place `KC_TRANS` on overlay layer changes just part of layout to fall back on lower or base layer.
Key with `KC_TRANS` (`KC_TRNS` and `_______` are the alias) doesn't has its own keycode and refers to lower valid layers for keycode, instead.
## Anatomy Of A `keymap.c`
## Anatomy Of A `keymap.c`
For this example we will walk through the [default Clueboard keymap](https://github.com/qmk/qmk_firmware/blob/master/keyboards/clueboard/keymaps/default/keymap.c). You'll find it helpful to open that file in another browser window so you can look at everything in context.
For this example we will walk through the [default Clueboard keymap](https://github.com/qmk/qmk_firmware/blob/master/keyboards/clueboard/keymaps/default/keymap.c). You'll find it helpful to open that file in another browser window so you can look at everything in context.
@ -140,7 +215,6 @@ To actually handle the keypress event we define an `action_function()`. This fun
This should have given you a basic overview for creating your own keymap. For more details see the following resources:
This should have given you a basic overview for creating your own keymap. For more details see the following resources:
* https://github.com/qmk/qmk_firmware/blob/master/doc/keymap.md (If you see `static const uint8_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS]`, it is still the TMK code example code.)
Osamu Aoki
8 years ago