1fa27139f5
Split out NVM access code in the AVRISP project into a seperate NVMTarget.c source file and header. Make NVM register accesses use the NVM base address as set by the host, rather than using the fixed value from the XMEGA datasheet.
15 years ago
3705330dd3
Use -pedantic compile time option to find and correct several minor code errors.
15 years ago
307ba254d5
The AVRISP project can now enter PDI mode under both bit-bang and hardware USART connection modes, tested against the XPLAIN board hardware. Still need to complete higher level NVM access code so that the device's memories can be read and written.
15 years ago
33a46b243a
PDI NVM enable is fast enough that bare polling is enough without a fixed delay in between each attempt. Make sure the USART transmitter is enabled explicitly when the USART is configured, so that repeated attempts to re-enter PDI mode don't fail due to TXEN not being set.
15 years ago
66201a05e9
Fix PDI code - must send NVM enable key least significant byte first, need to make sure Tx and Rx is switched correctly including disabling the output on the Tx line when receiving.
15 years ago
7e5966c1a8
Fix AVRISP PDI protocol - make sure inverted masks have the appropriate parenthesis around them, make sure the BREAK command for the hardware USART has 12 clock cycles exactly. Poll NVM Enable bit in the target's STATUS PDI register with a timeout, as it is not set immediately.
15 years ago
42cfd15793
Change over AVRISP project to have both hardware USART and software USART modes for the PDI protocol, when enabled. Fix up PDI initialisation routines.
15 years ago
7aecda6fda
Fix PDITarget_ReceiveByte() not discarding the start bit properly, and reading in the bits inverted and in the wrong order.
15 years ago
1e3513ed70
Add even parity bit to the software USART framing in the AVRISP project's PDI programming code.
15 years ago
9c8ed168e5
Fix inverted bit-banged USART logic in the AVRISP project for PDI programming. Add a delay to the clock toggling in the AVRISP project to ensure that the programming speed does not exceed 10MHz under any conditions to satisfy the limits in the datasheet for all target voltages. Fix incorrect pin being used as the DATA in in PDI programming mode.
15 years ago
7ace314cc1
Increase timeout of Mass Storage and Still Image host commands to 10 seconds (up from 5) to account for slow-processing devices.
...
Added brace guards to macros with parameters to prevent unintended changed evaluation of the macro expression.
Minor code cleanups (remove redundant comments, fix spacing, etc.).
15 years ago
2281750b5f
Make sure that USB_STREAM_TIMEOUT_MS is set in the MassStorageHost ClassDriver demo, so that slow devices don't time out the data pipe. Increase pipe timeout in both MassStorageHost demos to 5 seconds to account for the really slow devices.
...
Fix TeensyHID bootloader not properly shutting down the USB interface to trigger a disconnection on the host before resetting the AVR.
15 years ago
2919aeeaab
Fixed HID Parser not distributing the Usage Min and Usage Max values across an array of report items.
...
Added new HID_ALIGN_DATA() macro to return the pre-retrieved value of a HID report item, left-aligned to a given datatype.
Added new PreviousValue to the HID Report Parser report item structure, for easy monitoring of previous report item values.
15 years ago
f338ddcb87
Make sure the protocol handler files are included in the Doxygen documentation of the AVRISP project.
15 years ago
258a6a0177
Fix the tokens which enable and disable the different programming protocols in the AVRISP project.
15 years ago
f1baf12fae
Auto-configure AVRISP programmer configuration when built for the XPLAIN board to match the XPLAIN hardware connections.
15 years ago
a5adbae652
Document the PDI programming routines implemented so far in the AVRISP project. Add ability to selectively disable ISP programming support in addition to the existing ability to disable PDI programming support.
15 years ago
f69f03cb0d
Started implementing the low level PDI protocol in the AVRISP project, for XMEGA device programming.
15 years ago
f92b56191d
Add new more reliable software UART for the XPLAINBridge project by David Prentice and Peter Danneger.
15 years ago
fec31947a6
Removed John Steggall's software UART code from the XPLAIN Bridge project due to reliability issues.
15 years ago
1f8dfd0205
Add support for unwrapping of the XMEGA PDI programming protocol to the AVRISP Programmer project.
15 years ago
5930f47bf4
Rename V2ProtocolTarget files to ISPTarget in the AVRISP Programmer Clone project.
15 years ago
1ed6925b5b
Factor out all the ISP related code into a seperate ISPProtocol set of files in the AVRISP Clone programmer project, to clearly seperate out the programming protocols when PDI programming is implemented.
15 years ago
1645c3d243
Rename the V2Protocol command handlers in the AVRISP project in preperation of XMEGA PDI programming support.
15 years ago
1b2cd16976
Added CDC_Host_Flush() function to the CDC Host Class driver to flush sent data to the attached device.
15 years ago
e5057fec8e
Enable pullup on the PD5 pin of the AVR in the XPLAINBridge project - this is connected to the XMEGA's /RESET line, need to enable pullup to prevent spurrious resets.
15 years ago
f37d21bbe9
Updated John Steggall's software USART in the XPLAINBridge project.
15 years ago
a04131cf04
Fix more Doxygen errors from missing parameter documentation.
15 years ago
50f4a3b625
Fix build and Doxygen errors.
15 years ago
8c6c27d88b
Added new RNDISHost Host LowLevel demo. Fixed misnamed Pipe_SetPipeToken() macro for setting a pipe's direction. Fixed CDCHost failing on devices with bidirectional endpoints.
15 years ago
c05c7c7df4
Added new XPLAIN serial Bridge project (thanks to John Steggall for the software UART code).
15 years ago
d3f11eb528
Make the StandaloneProgrammer project seamlessly read out drive contents from either an attached FAT formatted drive when in host mode, or the onboard FAT formatted dataflash when in device mode.
15 years ago
702bec892d
Fixed misnamed SI_Host_USBTask() and SI_Host_ConfigurePipes() functions.
15 years ago
8b009bc113
Added new ReportType parameter to the HID Device Class driver CALLBACK_HID_Device_CreateHIDReport() callback to indicate the report type to generate.
15 years ago
aaa0bed556
The incomplete StandaloneProgrammer project now uses Host and Device Mass storage classes, so that program data can either be loaded onto the device's Dataflash storage, or read off an attached USB memory stick.
...
The USB target family and allowable USB mode tokens are now public and documented (USB_CAN_BE_*, USB_SERIES_*_AVR).
The SCSI_Request_Sense_Response_t and SCSI_Inquiry_Response_t type defines are now part of the Mass Storage Class driver common defines, rather than being defined in the Host mode Class driver section only.
The USB_MODE_HOST token is now defined even when host mode is not available.
Added missing CDC_Host_CreateBlockingStream() function code to the CDC Host Class driver.
15 years ago
86db035b1e
Add activity LED updates to the AVRISP project.
15 years ago
7ef58eef7a
Fixed LowLevel Keyboard demo not saving the issued report only after it has been written to the endpoint.
...
Added support for multiple keyboard keycodes in a single report to the LowLevel and ClassDriver Keyboard demos.
15 years ago
9b20114555
Make RNDISHost demo validate the set Packet Filter to ensure that it is being sent correctly.
...
Add new (incomplete) StandaloneProgrammer project, using the ELM Petite FAT library to read files stored on the board's dataflash by the host.
15 years ago
e625fd6df3
Corrected the name of the misnamed USB_GetDeviceConfigDescriptor() function to USB_Host_GetDeviceConfigDescriptor().
15 years ago
d6edfe35c8
Spell check all source code variables, comments and strings.
15 years ago
c647c27639
Minor changes to the AVRISP project for code clarity.
15 years ago
4dde844e9f
Remove dependancies from the LowLevel demos to the ClassDriver demos, since the use of ClassDriver headers now outputs an error when NO_STREAM_CALLBACKS is used.
15 years ago
34dc7f241f
Make Low Level host demos use void pointers for the configuration descriptor, to prevent warnings when passed to the altered configuration descriptor parsing routines.
...
Added preprocessor checks to give a human readable error when the class drivers are used when the incompatible NO_STREAM_CALLBACKS compile time option is used.
15 years ago
f29fc1abc4
Add double banking property to LUFA powered projects in the Projects directory. Add guards to macro parameters to ensure that formulas passed as parameters don't mess up the internal macro structure.
15 years ago
9ea891ea20
Use clearer buffer names in the USBtoSerial project to prevent confusion.
15 years ago
de70f0f1cf
Moved USBtoSerial demo the Projects directory, as it is simply an expanded CDC demo. Added const qualifier to Endpoint/Pipe stream write routines.
15 years ago
c3dfc58707
Fix invalid Event name rule in demo/project makefiles.
15 years ago
dc68de15b6
Make Audio device demos compatible with AVRs running at 16MHz instead of 8MHz.
...
Fix up demo documentation device compatibility list to be as general as possible to reduce changes required as Atmel releases more devices within the same USB AVR series.
15 years ago
664a292181
Application documentation/comment cleanup.
15 years ago
3ecc462954
Added pinouts to the AVRISP project for a standard ISP 6 Pin header to make construction of a standard ISP programmer easier.
15 years ago
Dean Camera