e331b531c6
Change over instances of "make" in the makefiles to "$(MAKE)" to allow for the make tool to be overridden.
15 years ago
ab8668b14e
Removed software PDI/TPI emulation from the AVRISP-MKII clone project, as it was very buggy. PDI and TPI must now be implemented via seperate headers instead of the one unified ISP/TPI/PDI header.
15 years ago
27f0ba6fc3
Fixed device state not being reset back to the default state if the host sets the address to 0x00.
...
Fixed Set Configuration requests not being stalled until the host has set the device's address.
Fixed possibility of internal signature retrieval being corrupted if an interrupt occurs during a signature byte read (thanks to Andrei Krainev).
15 years ago
eed7d4df6a
Added new ENDPOINT_*_BusSuspended error code to the Endpoint function, so that the stream functions early-abort if the bus is suspended before or during a transfer.
15 years ago
5c0c0327d5
Increase hardware PDI/TPI programming speed to 1MHz in the AVRISP MKII clone project.
15 years ago
a5e79333e5
Switch back to C based timeout ISR in the AVRISP project - assembly version was failing, and only one or two cycles could be shaved off the compiler generated code.
15 years ago
3d28d53c3e
Change AVRISP project's timeout to be interrupt based again, but make the interrupt itself interruptable and use a seperate assembly file to hand-optimize the ISR code.
...
Removed the cast to uint16_t on the set baud rate in the USBtoSerial project, so that the higher >1M baud rates can be selected (thanks to Steffan).
15 years ago
9a1560dc05
Make sure that long reads are aborted early if the connection times out while waiting on more bytes in the AVRISP MKII clone project.
15 years ago
ceb16ee24f
Make sure that the NVM bus/controller busy waits in the AVRISP MKII clone project abort properly if a timeout occurs while waiting for a response.
15 years ago
e977774d4e
Relocate USBInterrupt.c/.h from the HighLevel USB driver directory to the LowLevel directory as it is hardware-dependent.
15 years ago
59c4871f80
USB_Init() no longer calls sei() to enable global interrupts - this must now be done in the user application once all init code has run.
15 years ago
85aaaf84ce
Make AVRISP-MKII clone project's software PDI/TPI mode more robust by keeping track of timeouts while waiting for a Tx/Rx to finish.
15 years ago
5993e1efe7
Added ability to search by Channel PSM to the GetChannelData() function in the BluetoothHost demo.
...
Added new HCI states to properly initialize the bluetooth dongle and retrieve the local BDADDR.
Factored out Bluetooth state information into a new state structure for easy reference in the user application.
Added new StackInitialized() Bluetooth stack callback function.
15 years ago
ee74b4948f
Add information request/response signal handler to the Bluetooth Host demo.
...
Ensure that the AVRISP-MKII project's Windows avrdude compatibility define is named properly in all parts of the code.
15 years ago
fa1a092901
Add user callback function to the Bluetooth host demo to filter out connections from remote devices. Add in ability to reject connections based on their bluetooth device address.
...
Clean up RelayBoard project code.
Make AVRISP project clear the XMEGA target's reset register twice; this does not appear to take affect properly the first time under some circumstances.
15 years ago
c9148f9b47
Added WIN_LIBUSB_COMPAT compile time option to the AVRISP programmer project to make the code compatible with Windows builds of avrdude at the expense of AVRStudio compatibility.
15 years ago
49b09a2042
Standardized the naming scheme given to configuration descriptor sub-elements in the Device mode demos, bootloaders and projects.
...
Fix errors in the MouseHostWithParser demo from incorrect use of the HID_ALIGN_DATA() macro.
15 years ago
72527867f6
Remove redundant check in the software PDI programming code of the AVRISP project.
15 years ago
9a5ae36a4f
Software PDI mode breaks unless the software USART has 100 cycles between bits.
15 years ago
2b74b517ea
Don't enable the pullup on the target /RESET line in the AVRISP project for PDI mode - clearing the XMEGA's reset control register twice is enough to release it from reset. Possible silicon bug, since the official Atmel programmers have the same issue.
15 years ago
39d56aeffe
Fixed PDI programming mode in the AVRISP programmer project not exiting programming mode correctly (clear target Reset key twice, set /RESET pin to pullup).
...
Add newlines to the MIDI event printf() statements in the MIDI host demos.
15 years ago
071fd8ce53
Revert changes made for the partial port to the AVR32 architecture.
15 years ago
e11fddfe66
Update Temperature board driver to be AVR32 compatible when the ADC peripheral driver is eventually ported. Make architecture includes explicit for both the AVR32 and the AVR8, to make way for future architecture ports.
...
Add SPI driver aliases for the old function names in the AVR8 driver, so that existing code will still compile against the new version.
15 years ago
c24027f3b5
Fixed software PDI/TPI programming mode in the AVRISP project not correctly toggling just the clock pin.
...
Fix broken AVR8 Serial peripheral driver.
15 years ago
d2851b3351
Oops - need to revert changes made to ease testing of the software PDI programming mode.
15 years ago
5e12d436fa
Remove dual ISR for software PDI mode, use a single ISR instead to reduce code complexity.
15 years ago
e322f14620
More fixes to the AVRISP command timeout system so that it should no longer lock up while processing command no matter what the conditions.
15 years ago
12a01ed72d
Increased the speed of both software and hardware TPI/PDI programming modes of the AVRISP project.
15 years ago
10b9394a8b
Oops - missed a few references to the old global TimeoutMSRemaining counter in ISPTarget.c of the AVRISP-MKII clone project.
15 years ago
ce8d0424b1
AVRISP programmer project now has a more robust timeout system, allowing for a doubling of the software USART speed for PDI and TPI programming.
15 years ago
de0ccb3d09
Add NO_VTARGET_DETECT compile time option to the AVRISP-MKII clone project, to disable VTARGET detection on AVR models with an on-chip ADC.
15 years ago
3a2c1db675
Fixed lack of SECTION ERASE command in TPI programming mode of the AVRISP project preventing fuses from being cleared.
15 years ago
ab195ab1da
Added .5MHz recovery clock to the AVRISP programmer project when in ISP programming mode to correct mis-set fuses.
...
Fixed AVRISP project not extending the command delay after each successful page/word/byte program.
15 years ago
35a0fe9384
Fixed USB_GetHIDReportSize() returning the number of bits in the specified report instead of bytes.
...
Moved the USB_GetHIDReportItemInfo() calls into the main report item passing loop in the *HostWithParser demos - it is fast enough not to effect performance, and avoids duplicate code.
Make Webserver project report the LUFA version as part of the HTTP header.
15 years ago
3ab0b3a027
Fix LowLevel Keyboard demo -- accidentally trying to dereference a uint8_t type in ProcessLEDReport().
15 years ago
7ae91099e9
Fix AVRISP-MKII clone project's TPI Chip Erase command processing - ensure erase location is the high byte in the given address space, check NVMBUSY for completion rather than the NVM Bus Enable bit.
...
Change If-Else chains over to switch statements in XPROGProtocol.c for clarity.
15 years ago
15f84bb8f5
New BOARD value option BOARD_NONE (equivelent to not specifying BOARD) which will remove all board hardware drivers which do not adversely affect the code operation (currently only the LEDs driver).
...
Spell-check code/comments in the Webserver/AVRISP-MKII projects.
15 years ago
77e86e7d82
Exlude the "INCLUDE_FROM_*" macros from the individual project's documentation.
15 years ago
53eca61d02
Minor fixups to the documentation and preprocessor tokens.
15 years ago
5687ac7316
Fix TPI mode chip erase code not properly erasing the target memory space.
15 years ago
8d49480891
Oops - new Write Word alignment code in the TPI programming function means that the WriteBuffer parameter is no longer const.
15 years ago
ec6fbb219f
Make TPI writes add a dummy high byte if the data isn't word-aligned.
15 years ago
b736a5ef2b
Make TPI programming protocol program in words, not bytes to satisfy the datasheet conditions.
15 years ago
4d246a82cb
Fixed incorrect values of USB_CONFIG_ATTR_SELFPOWERED and USB_CONFIG_ATTR_REMOTEWAKEUP tokens (thanks to Claus Christensen).
...
Mark the AVRISP-MKII project descriptors as being both Bus Powered and Device Powered.
Copy over file level documentation of the peripheral drivers to the module level documentation.
15 years ago
9e7ffcb014
Make AVRISP XPROG function parameters const where possible.
15 years ago
5f363996e3
Fixed issues with EEPROM and FLASH ISP programming in the AVRISP project.
15 years ago
331e8dece6
Use _delay_us() function in the XPROGTarget.c file to ensure timing requirements are met, rather than a fixed number of NOPs.
15 years ago
75d27f8ef0
Oops - PDI handshake delay was too long, causing the device's /RESET functionality to be re-enabled.
15 years ago
a114878209
Oops - TPI programming is broken in the AVRISP project because the busy-flag check wasn't inverting the result.
15 years ago
872f61ff53
Fix TPI communications in the AVRISP project when bit-banged USART mode is selected.
15 years ago
Dean Camera