![]() |
11 years ago | |
---|---|---|
.. | ||
doc | 11 years ago | |
Makefile | 11 years ago | |
Makefile.iwrap | 12 years ago | |
Makefile.pjrc | 11 years ago | |
Makefile.vusb | 12 years ago | |
README.md | 11 years ago | |
config.h | 11 years ago | |
config_iwrap.h | 11 years ago | |
config_vusb.h | 12 years ago | |
iwrap.txt | 12 years ago | |
keymap.c | 11 years ago | |
led.c | 11 years ago | |
matrix.c | 11 years ago | |
usbconfig.h | 12 years ago |
README.md
Alternative Controller for HHKB Pro
I wanted to add some features like vi cursor and mouse keys to my HHKB but its controller is not programmable and firmware source code is not open, of course. This means customizing this keyboard needs to replace original controller with programmable one. This controller can work with HHKB Professional and Professional 2 model.
See this thread in geekhack.org.
##Features
- Customizable keymap
- More keymap layers(more Fn keys)
- Mouse keys
- USB NKRO
See README of tmk_keyboard for more.
###Pros
- No risks: Everything is all reversible
- No need for PCB trace patching, case cutting or any other destructive mod
- Can keep original controller intact
- Can change all HHKB behaviour as you like
###Cons
- Void your warranty
- Lose USB hub function of Pro2
##DISCLAIMER I'm not a professional of electronics nor MCU programming. This may damage your HHKB. And my English writing is poor, I'm not sure I can convey my notions accurately.
##Documents See doc/HHKB.txt and files under doc/ for internal of HHKB and this controller.
##Build Firmware & Program See this document first.
Configuration
Set MCU
, BOOTLOADER_SIZE
and other build options in Makefile
and config.h
.
Build
Just run make after intall tools.
$ make
Use Makefile.pjrc
if you want to use PJRC stack instead of LUFA.(LUFA is recommended.)
$ make -f Makefile.pjrc
Use Makefile.vusb
for V-USB controller.(not supported actively any more.)
$ make -f Makefile.vusb
Program
First, push reset button on board to start bootloader.
This command programs the controller with dfu-programmer if the tool is intalled and configured properly.
$ make dfu
Or you can also use FLIP command to program. Also the tool should be intalled and configured properly. FLIP GUI app is also available.
$ make flip
Use Teensy Loader if your controller is Teensy/Teensy++.
##How to Customize See tmk_keyboard documents.
##Hardware You have some options for hardware. Development boards with USB AVR family(ATMega32U4, AT90USB1286) like Teensy will work while MegaAVR with V-USB library is also cheapear option for DIY.
###1. TMK Alt Controller Board TMK designed Keyboard Controller Board for HHKB Pro2(KiCad project). See this post.
###2. PJRC Teensy++ 2.0 connection +---------------+ | Teensy++ | | | | | HHKB pro HHKB pro2 | | ~~~~~~~~ ~~~~~~~~~ | PB0-2|------->ROW (6-8) (5-7) | PB3-5|------->COL (9-11) (8-10) | PB6|------->ENABLE (12) (11) | PE6|<-------KEY (4) (3) | PE7|------->PREV (5) (4) | | | | 5V--- (1-3) (1-2) | | GND--- (13-14) (12-13) +---------------+
- NOTE: PJRC Teensy
###3. V-USB connection +---+ +---------------+ USB GND | | ATmega328p | ~~~ C3 | | 5V <-------+--------+---|Vcc,AVCC | HHKB pro pro2 R1 | | ~~~~~~~~ ~~~~ D- <----+--+-----R2-----|INT1 PB2-4|------->ROW (6-8) (5-7) D+ <----|---+----R3-----|INT0 PC0-2|------->COL (9-11) (8-10) Z1 Z2 | PC3|------->ENABLE (12) (11) GND<----+---+-----------|GND PB0|<-------KEY (4) (3) | PB1|------->PREV (5) (4) | | GND+-C2--+--|XTAL1 RXD|------->Debug Console X1 | TXD|<-------Debug Console GND+-C3--+--|XTAL2 RST|---SW--+GND +---------------+ R1: 1.5K Ohm R2,R3: 68 Ohm Z1,Z2: Zener 3.6V C1,C2: 22pF C3: 0.1uF X1: Crystal 12MHz SW: Push Switch(for bootloader)
- NOTE: See V-USB documentation for more detail of hardware and the USB stack.
- NOTE: USBaspLoader is very useful for firmware update.