8cb71ac35d
PCB: 3D shapes for pushbuttons
6 years ago
51d9149ec7
PCB: capacitors rerouted with clearance
6 years ago
4dbc97961f
PCB: re-run DRC
6 years ago
49bdc24d97
PCB: C54 22uF for 3V RTC battery and battery pad clearance
6 years ago
197b1166a2
PCB: removing obsolete traces from US2 connector
6 years ago
10b285212c
PCB: kicad 5 load and save
6 years ago
67d91dda07
PCB: export paste layer
6 years ago
adb7e6eef1
PCB: v1.8 capacitor for 2.5/3.3V
6 years ago
4cd2f833d7
PCB: v1.7.16 capacitor near SDRAM and trac cosmetix
6 years ago
5775212c8c
PCB: trac cosmetix++
...
Numerous small route optimizations,
Reducing inductive loops at copper fill areas on
board power distribution.
preparation to send for production of v1.8
6 years ago
3606470a5c
PCB: v1.7.15 J1,2 22nF capacitors
6 years ago
066d71f2fb
PCB: 2V5_3V3 on J1
6 years ago
68eed4b791
PCB: silkscreen writing 2.5V/3.3V under the jumper
6 years ago
1f6e8b240d
PCB: Voltage selection header moved deeper inside PCB
6 years ago
5216447da2
PCB: remove micro hdmi connector from library paths and change
...
3D footprint of 2.5/3.3V jumper to angled 2.54 mm header.
As shown, angled connector will occupy space required for
plugging HDMI connector.
The header should be placed deeper inside if possible.
6 years ago
4ef3866cea
PCB: join power supply copper fill areas under BGA and track clenaup
6 years ago
ff4f1ee73e
PCB: C47 for 2.5/3.3V
6 years ago
44b9cee496
PCB: shortening SW1-4 tracks, thicker 2.5/3.3V track
6 years ago
9c8ffbe076
PCB: C26 connected to 2.5/3.3V
6 years ago
4eee6bb940
PCB: initially routed 2.5/3.3V selector, routes too thin,
...
capacitors missing, J1 supply output is still 3.3V
6 years ago
6629615471
PCB: trac cosmetix
6 years ago
689ab40e75
trac cosmetix
6 years ago
471fd872fe
PCB: usb pull pins routed to gpdi bank
6 years ago
cf37ea3128
readme update, trac cosmetix
6 years ago
52eb5b3123
PCB: moving J3 (wifi off) jumper aligned to 2.54 mm grid
6 years ago
e9b0b4d878
PCB: trac cosmetix
6 years ago
e7744d74a1
PCB: silkscreen cosmetix
6 years ago
507733bbbf
PCB: reconnecting 3.6V zeners
6 years ago
7c8af52234
PCB: silkcreen cosmetix
6 years ago
a5766c0945
PCB: move silkscreen 5V bit away from the edge
6 years ago
8d1fd0d249
PCB: v1.7.14 follwing the schematics and trac cosmetix
6 years ago
28af6b386b
PCB: trac and silkscreen cosmetix around HDMI,
...
only C36,C45 capacitor references visible, inbetween
hidden for clarity (all values are the same).
6 years ago
0ad6b06474
PCB: silkscreen unclutter around bottom jtag pinout
6 years ago
19aba5f7c8
PCB: power decoupling capacitor near OLED
...
22nF footprints currently not reduced to non-handsoldering
6 years ago
5b2e0d6e49
PCB v1.7.12: AC couping all GPDI differential lines
6 years ago
1f2f7945e6
PCB: GPDI HEAC capacitors
6 years ago
1473104281
PCB: 0-ohm resistors as jumpers, trac cosmetix
6 years ago
b98fc63ded
PCB: trac cosmetix
6 years ago
afc3dc5d59
PCB: uncluttering silkscreen
6 years ago
deff67d9ac
PCB: v1.7.11
6 years ago
ea4642253c
PCB: move pullupdown diodes
6 years ago
096bc24d4f
PCB: diodes pull up/down 1.5k/15k
6 years ago
a293862950
PCB: US2 routed for 15k pull
6 years ago
3292e8285d
PCB: hide RIZ insignia until production
6 years ago
d8890ff9b5
PCB: logos update
6 years ago
bb66be0234
PCB v1.7.10: additional 2 lines for US2
6 years ago
6cd951119f
PCB: silkscreen cosmetix
6 years ago
367641a68c
PCB: 3 decoupling 22nF capacitors for SDRAM
6 years ago
7c8c9c52a6
PCB: sprinkling 22nF decoupling capacitors under FPGA
6 years ago
e25708d9ab
PCB: swap SD_CLK and SD_D2
6 years ago
davor