391 Commits (c51909d4976c2561231feea761bb3026a9a19e1a)

Author	SHA1	Message	Date
davor	4dbc97961f	PCB: re-run DRC	7 years ago
davor	49bdc24d97	PCB: C54 22uF for 3V RTC battery and battery pad clearance	7 years ago
davor	197b1166a2	PCB: removing obsolete traces from US2 connector	7 years ago
davor	10b285212c	PCB: kicad 5 load and save	7 years ago
davor	67d91dda07	PCB: export paste layer	7 years ago
davor	adb7e6eef1	PCB: v1.8 capacitor for 2.5/3.3V	7 years ago
davor	4cd2f833d7	PCB: v1.7.16 capacitor near SDRAM and trac cosmetix	7 years ago
davor	5775212c8c	PCB: trac cosmetix++ ... Numerous small route optimizations, Reducing inductive loops at copper fill areas on board power distribution. preparation to send for production of v1.8	7 years ago
davor	3606470a5c	PCB: v1.7.15 J1,2 22nF capacitors	7 years ago
davor	066d71f2fb	PCB: 2V5_3V3 on J1	7 years ago
davor	68eed4b791	PCB: silkscreen writing 2.5V/3.3V under the jumper	7 years ago
davor	1f6e8b240d	PCB: Voltage selection header moved deeper inside PCB	7 years ago
Emard	5216447da2	PCB: remove micro hdmi connector from library paths and change ... 3D footprint of 2.5/3.3V jumper to angled 2.54 mm header. As shown, angled connector will occupy space required for plugging HDMI connector. The header should be placed deeper inside if possible.	7 years ago
Emard	4ef3866cea	PCB: join power supply copper fill areas under BGA and track clenaup	7 years ago
Emard	ff4f1ee73e	PCB: C47 for 2.5/3.3V	7 years ago
Emard	44b9cee496	PCB: shortening SW1-4 tracks, thicker 2.5/3.3V track	7 years ago
Emard	9c8ffbe076	PCB: C26 connected to 2.5/3.3V	7 years ago
davor	4eee6bb940	PCB: initially routed 2.5/3.3V selector, routes too thin, ... capacitors missing, J1 supply output is still 3.3V	7 years ago
davor	6629615471	PCB: trac cosmetix	7 years ago
davor	689ab40e75	trac cosmetix	7 years ago
davor	471fd872fe	PCB: usb pull pins routed to gpdi bank	7 years ago
davor	cf37ea3128	readme update, trac cosmetix	7 years ago
davor	52eb5b3123	PCB: moving J3 (wifi off) jumper aligned to 2.54 mm grid	7 years ago
Emard	e9b0b4d878	PCB: trac cosmetix	7 years ago
davor	e7744d74a1	PCB: silkscreen cosmetix	7 years ago
davor	507733bbbf	PCB: reconnecting 3.6V zeners	7 years ago
davor	7c8af52234	PCB: silkcreen cosmetix	7 years ago
davor	a5766c0945	PCB: move silkscreen 5V bit away from the edge	7 years ago
Emard	8d1fd0d249	PCB: v1.7.14 follwing the schematics and trac cosmetix	7 years ago
Emard	28af6b386b	PCB: trac and silkscreen cosmetix around HDMI, ... only C36,C45 capacitor references visible, inbetween hidden for clarity (all values are the same).	7 years ago
davor	0ad6b06474	PCB: silkscreen unclutter around bottom jtag pinout	7 years ago
davor	19aba5f7c8	PCB: power decoupling capacitor near OLED ... 22nF footprints currently not reduced to non-handsoldering	7 years ago
davor	5b2e0d6e49	PCB v1.7.12: AC couping all GPDI differential lines	7 years ago
davor	1f2f7945e6	PCB: GPDI HEAC capacitors	7 years ago
Emard	1473104281	PCB: 0-ohm resistors as jumpers, trac cosmetix	7 years ago
davor	b98fc63ded	PCB: trac cosmetix	7 years ago
davor	afc3dc5d59	PCB: uncluttering silkscreen	7 years ago
davor	deff67d9ac	PCB: v1.7.11	7 years ago
davor	ea4642253c	PCB: move pullupdown diodes	7 years ago
davor	096bc24d4f	PCB: diodes pull up/down 1.5k/15k	7 years ago
davor	a293862950	PCB: US2 routed for 15k pull	7 years ago
davor	3292e8285d	PCB: hide RIZ insignia until production	7 years ago
davor	d8890ff9b5	PCB: logos update	7 years ago
Emard	bb66be0234	PCB v1.7.10: additional 2 lines for US2	7 years ago
davor	6cd951119f	PCB: silkscreen cosmetix	7 years ago
davor	367641a68c	PCB: 3 decoupling 22nF capacitors for SDRAM	7 years ago
davor	7c8c9c52a6	PCB: sprinkling 22nF decoupling capacitors under FPGA	7 years ago
davor	e25708d9ab	PCB: swap SD_CLK and SD_D2	7 years ago
davor	563aae12c3	PCB: improving traces to decoupling capacitors under FPGA	7 years ago
davor	b99ce33251	schematics and PCB: swap WIFI GPIO5 GPIO17	7 years ago