Fix for Z-endstop failure in .22

Marlin/Conditionals_LulzBot.h

@@ -37,7 +37,7 @@
     #error Must specify model and toolhead. Please see "Configuration_LulzBot.h" for directions.
 #endif
 
-#define LULZBOT_FW_VERSION ".22"
+#define LULZBOT_FW_VERSION ".23"
 
 // Select options based on printer model
 
@@ -141,6 +141,12 @@
     #define LULZBOT_Z_MIN_PROBE_ENDSTOP
     #define LULZBOT_Z_MIN_PROBE_PIN               SERVO0_PIN // Digital pin 22
     #define LULZBOT_BAUDRATE 250000
+
+    // On the TAZ, the bed washers are on Z_MIN_PROBE while the
+    // Z-Home button is on Z_MIN, yet we need both to be disabled
+    // when z_probe_enabled is false. We added this special case
+    // to "endstops.cpp"
+    #define LULZBOT_Z_MIN_USES_Z_PROBE_ENABLED
 #endif
 
 #define LULZBOT_USE_CONTROLLER_FAN
@@ -298,7 +304,7 @@
  *
  * On TAZ:
  *   Z_MIN_PIN corresponds to the Z-Home push button.
- *   LULZBOT_Z_MIN_PROBE_PIN are the bed washers.
+ *   Z_MIN_PROBE_PIN are the bed washers.
  */
 #if defined(LULZBOT_MINI_BED)
     #define LULZBOT_ENABLE_PROBE_PINS(enable) { \
@@ -321,12 +327,16 @@
             WRITE(LULZBOT_Z_MIN_PROBE_PIN, HIGH); \
             SET_INPUT(Z_MIN_PIN); \
             WRITE(Z_MIN_PIN, HIGH); \
+            /* The following is required since Marlin would \
+             * not normally deploy the probe for Z-Min */ \
+            endstops.enable_z_probe(true); \
         } else { \
             /* Ground both pins to prevent EMI */ \
             SET_OUTPUT(LULZBOT_Z_MIN_PROBE_PIN); \
             WRITE(LULZBOT_Z_MIN_PROBE_PIN, LOW); \
             SET_OUTPUT(Z_MIN_PIN); \
             WRITE(Z_MIN_PIN, LOW); \
+            endstops.enable_z_probe(false); \
         } \
     }
 #endif

Marlin/Marlin_main.cpp

@@ -3917,6 +3917,8 @@ inline void gcode_G28(const bool always_home_all) {
 
   #endif // !DELTA (gcode_G28)
 
+  LULZBOT_AFTER_Z_HOME_ACTION // This must happen before endstops.not_homing()
+
   endstops.not_homing();
 
   #if ENABLED(DELTA) && ENABLED(DELTA_HOME_TO_SAFE_ZONE)
@@ -3935,8 +3937,6 @@ inline void gcode_G28(const bool always_home_all) {
     tool_change(old_tool_index, 0, true);
   #endif
 
-  LULZBOT_AFTER_Z_HOME_ACTION
-
   lcd_refresh();
 
   report_current_position();

Marlin/endstops.cpp

@@ -409,7 +409,7 @@ void Endstops::update() {
 
         #else // !Z_DUAL_ENDSTOPS
 
-          #if ENABLED(Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN)
+          #if ENABLED(Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN) || defined(LULZBOT_Z_MIN_USES_Z_PROBE_ENABLED)
             if (z_probe_enabled) UPDATE_ENDSTOP(Z, MIN);
           #else
             UPDATE_ENDSTOP(Z, MIN);