|
|
|
@ -1015,23 +1015,17 @@
|
|
|
|
#define PREHEAT_2_TEMP_BED 60 // K8200: ABS / set back to 110 if you have an upgraded heatbed power supply
|
|
|
|
#define PREHEAT_2_TEMP_BED 60 // K8200: ABS / set back to 110 if you have an upgraded heatbed power supply
|
|
|
|
#define PREHEAT_2_FAN_SPEED 0 // Value from 0 to 255
|
|
|
|
#define PREHEAT_2_FAN_SPEED 0 // Value from 0 to 255
|
|
|
|
|
|
|
|
|
|
|
|
//
|
|
|
|
/**
|
|
|
|
// Nozzle Park -- EXPERIMENTAL
|
|
|
|
* Nozzle Park -- EXPERIMENTAL
|
|
|
|
//
|
|
|
|
*
|
|
|
|
// When enabled allows the user to define a special XYZ position, inside the
|
|
|
|
* Park the nozzle at the given XYZ position on idle or G27.
|
|
|
|
// machine's topology, to park the nozzle when idle or when receiving the G27
|
|
|
|
*
|
|
|
|
// command.
|
|
|
|
* The "P" parameter controls the action applied to the Z axis:
|
|
|
|
//
|
|
|
|
*
|
|
|
|
// The "P" paramenter controls what is the action applied to the Z axis:
|
|
|
|
* P0 (Default) If Z is below park Z raise the nozzle.
|
|
|
|
// P0: (Default) If current Z-pos is lower than Z-park then the nozzle will
|
|
|
|
* P1 Raise the nozzle always to Z-park height.
|
|
|
|
// be raised to reach Z-park height.
|
|
|
|
* P2 Raise the nozzle by Z-park amount, limited to Z_MAX_POS.
|
|
|
|
//
|
|
|
|
*/
|
|
|
|
// P1: No matter the current Z-pos, the nozzle will be raised/lowered to
|
|
|
|
|
|
|
|
// reach Z-park height.
|
|
|
|
|
|
|
|
//
|
|
|
|
|
|
|
|
// P2: The nozzle height will be raised by Z-park amount but never going over
|
|
|
|
|
|
|
|
// the machine's limit of Z_MAX_POS.
|
|
|
|
|
|
|
|
//
|
|
|
|
|
|
|
|
//#define NOZZLE_PARK_FEATURE
|
|
|
|
//#define NOZZLE_PARK_FEATURE
|
|
|
|
|
|
|
|
|
|
|
|
#if ENABLED(NOZZLE_PARK_FEATURE)
|
|
|
|
#if ENABLED(NOZZLE_PARK_FEATURE)
|
|
|
|
@ -1039,44 +1033,44 @@
|
|
|
|
#define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
|
|
|
|
#define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
|
|
|
|
#endif
|
|
|
|
#endif
|
|
|
|
|
|
|
|
|
|
|
|
//
|
|
|
|
/**
|
|
|
|
// Clean Nozzle Feature -- EXPERIMENTAL
|
|
|
|
* Clean Nozzle Feature -- EXPERIMENTAL
|
|
|
|
//
|
|
|
|
*
|
|
|
|
// When enabled allows the user to send G12 to start the nozzle cleaning
|
|
|
|
* Adds the G12 command to perform a nozzle cleaning process.
|
|
|
|
// process, the G-Code accepts two parameters:
|
|
|
|
*
|
|
|
|
// "P" for pattern selection
|
|
|
|
* Parameters:
|
|
|
|
// "S" for defining the number of strokes/repetitions
|
|
|
|
* P Pattern
|
|
|
|
//
|
|
|
|
* S Strokes / Repetitions
|
|
|
|
// Available list of patterns:
|
|
|
|
* T Triangles (P1 only)
|
|
|
|
// P0: This is the default pattern, this process requires a sponge type
|
|
|
|
*
|
|
|
|
// material at a fixed bed location. S defines "strokes" i.e.
|
|
|
|
* Patterns:
|
|
|
|
// back-and-forth movements between the starting and end points.
|
|
|
|
* P0 Straight line (default). This process requires a sponge type material
|
|
|
|
//
|
|
|
|
* at a fixed bed location. "S" specifies strokes (i.e. back-forth motions)
|
|
|
|
// P1: This starts a zig-zag pattern between (X0, Y0) and (X1, Y1), "T"
|
|
|
|
* between the start / end points.
|
|
|
|
// defines the number of zig-zag triangles to be done. "S" defines the
|
|
|
|
*
|
|
|
|
// number of strokes aka one back-and-forth movement. Zig-zags will
|
|
|
|
* P1 Zig-zag pattern between (X0, Y0) and (X1, Y1), "T" specifies the
|
|
|
|
// be performed in whichever dimension is smallest. As an example,
|
|
|
|
* number of zig-zag triangles to do. "S" defines the number of strokes.
|
|
|
|
// sending "G12 P1 S1 T3" will execute:
|
|
|
|
* Zig-zags are done in whichever is the narrower dimension.
|
|
|
|
//
|
|
|
|
* For example, "G12 P1 S1 T3" will execute:
|
|
|
|
// --
|
|
|
|
*
|
|
|
|
// | (X0, Y1) | /\ /\ /\ | (X1, Y1)
|
|
|
|
* --
|
|
|
|
// | | / \ / \ / \ |
|
|
|
|
* | (X0, Y1) | /\ /\ /\ | (X1, Y1)
|
|
|
|
// A | | / \ / \ / \ |
|
|
|
|
* | | / \ / \ / \ |
|
|
|
|
// | | / \ / \ / \ |
|
|
|
|
* A | | / \ / \ / \ |
|
|
|
|
// | (X0, Y0) | / \/ \/ \ | (X1, Y0)
|
|
|
|
* | | / \ / \ / \ |
|
|
|
|
// -- +--------------------------------+
|
|
|
|
* | (X0, Y0) | / \/ \/ \ | (X1, Y0)
|
|
|
|
// |________|_________|_________|
|
|
|
|
* -- +--------------------------------+
|
|
|
|
// T1 T2 T3
|
|
|
|
* |________|_________|_________|
|
|
|
|
//
|
|
|
|
* T1 T2 T3
|
|
|
|
// P2: This starts a circular pattern with circle with middle in
|
|
|
|
*
|
|
|
|
// NOZZLE_CLEAN_CIRCLE_MIDDLE radius of R and stroke count of S.
|
|
|
|
* P2 Circular pattern with middle at NOZZLE_CLEAN_CIRCLE_MIDDLE.
|
|
|
|
// Before starting the circle nozzle goes to NOZZLE_CLEAN_START_POINT.
|
|
|
|
* "R" specifies the radius. "S" specifies the stroke count.
|
|
|
|
//
|
|
|
|
* Before starting, the nozzle moves to NOZZLE_CLEAN_START_POINT.
|
|
|
|
// Caveats: End point Z should use the same value as Start point Z.
|
|
|
|
*
|
|
|
|
//
|
|
|
|
* Caveats: The ending Z should be the same as starting Z.
|
|
|
|
// Attention: This is an EXPERIMENTAL feature, in the future the G-code arguments
|
|
|
|
* Attention: EXPERIMENTAL. G-code arguments may change.
|
|
|
|
// may change to add new functionality like different wipe patterns.
|
|
|
|
*
|
|
|
|
//
|
|
|
|
*/
|
|
|
|
//#define NOZZLE_CLEAN_FEATURE
|
|
|
|
//#define NOZZLE_CLEAN_FEATURE
|
|
|
|
|
|
|
|
|
|
|
|
#if ENABLED(NOZZLE_CLEAN_FEATURE)
|
|
|
|
#if ENABLED(NOZZLE_CLEAN_FEATURE)
|
|
|
|
@ -1101,33 +1095,35 @@
|
|
|
|
#define NOZZLE_CLEAN_GOBACK
|
|
|
|
#define NOZZLE_CLEAN_GOBACK
|
|
|
|
#endif
|
|
|
|
#endif
|
|
|
|
|
|
|
|
|
|
|
|
//
|
|
|
|
/**
|
|
|
|
// Print job timer
|
|
|
|
* Print Job Timer
|
|
|
|
//
|
|
|
|
*
|
|
|
|
// Enable this option to automatically start and stop the
|
|
|
|
* Automatically start and stop the print job timer on M104/M109/M190.
|
|
|
|
// print job timer when M104/M109/M190 commands are received.
|
|
|
|
*
|
|
|
|
// M104 (extruder without wait) - high temp = none, low temp = stop timer
|
|
|
|
* M104 (hotend, no wait) - high temp = none, low temp = stop timer
|
|
|
|
// M109 (extruder with wait) - high temp = start timer, low temp = stop timer
|
|
|
|
* M109 (hotend, wait) - high temp = start timer, low temp = stop timer
|
|
|
|
// M190 (bed with wait) - high temp = start timer, low temp = none
|
|
|
|
* M190 (bed, wait) - high temp = start timer, low temp = none
|
|
|
|
//
|
|
|
|
*
|
|
|
|
// In all cases the timer can be started and stopped using
|
|
|
|
* The timer can also be controlled with the following commands:
|
|
|
|
// the following commands:
|
|
|
|
*
|
|
|
|
//
|
|
|
|
* M75 - Start the print job timer
|
|
|
|
// - M75 - Start the print job timer
|
|
|
|
* M76 - Pause the print job timer
|
|
|
|
// - M76 - Pause the print job timer
|
|
|
|
* M77 - Stop the print job timer
|
|
|
|
// - M77 - Stop the print job timer
|
|
|
|
*/
|
|
|
|
#define PRINTJOB_TIMER_AUTOSTART
|
|
|
|
#define PRINTJOB_TIMER_AUTOSTART
|
|
|
|
|
|
|
|
|
|
|
|
//
|
|
|
|
/**
|
|
|
|
// Print Counter
|
|
|
|
* Print Counter
|
|
|
|
//
|
|
|
|
*
|
|
|
|
// When enabled Marlin will keep track of some print statistical data such as:
|
|
|
|
* Track statistical data such as:
|
|
|
|
// - Total print jobs
|
|
|
|
*
|
|
|
|
// - Total successful print jobs
|
|
|
|
* - Total print jobs
|
|
|
|
// - Total failed print jobs
|
|
|
|
* - Total successful print jobs
|
|
|
|
// - Total time printing
|
|
|
|
* - Total failed print jobs
|
|
|
|
//
|
|
|
|
* - Total time printing
|
|
|
|
// This information can be viewed by the M78 command.
|
|
|
|
*
|
|
|
|
|
|
|
|
* View the current statistics with M78.
|
|
|
|
|
|
|
|
*/
|
|
|
|
#define PRINTCOUNTER
|
|
|
|
#define PRINTCOUNTER
|
|
|
|
|
|
|
|
|
|
|
|
//=============================================================================
|
|
|
|
//=============================================================================
|
|
|
|
@ -1139,78 +1135,79 @@
|
|
|
|
// K8200: for Display VM8201 with SD slot
|
|
|
|
// K8200: for Display VM8201 with SD slot
|
|
|
|
#if ENABLED(K8200_VM8201)
|
|
|
|
#if ENABLED(K8200_VM8201)
|
|
|
|
|
|
|
|
|
|
|
|
//
|
|
|
|
/**
|
|
|
|
// LCD LANGUAGE
|
|
|
|
* LCD LANGUAGE
|
|
|
|
//
|
|
|
|
*
|
|
|
|
// Here you may choose the language used by Marlin on the LCD menus, the following
|
|
|
|
* Select the language to display on the LCD. These languages are available:
|
|
|
|
// list of languages are available:
|
|
|
|
*
|
|
|
|
// en, an, bg, ca, cn, cz, de, el, el-gr, es, eu, fi, fr, gl, hr, it,
|
|
|
|
* en, an, bg, ca, cn, cz, de, el, el-gr, es, eu, fi, fr, gl, hr, it,
|
|
|
|
// kana, kana_utf8, nl, pl, pt, pt_utf8, pt-br, pt-br_utf8, ru, tr, uk, test
|
|
|
|
* kana, kana_utf8, nl, pl, pt, pt_utf8, pt-br, pt-br_utf8, ru, tr, uk, test
|
|
|
|
//
|
|
|
|
*
|
|
|
|
// :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'tr':'Turkish', 'uk':'Ukrainian', 'test':'TEST' }
|
|
|
|
* :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'tr':'Turkish', 'uk':'Ukrainian', 'test':'TEST' }
|
|
|
|
//
|
|
|
|
*/
|
|
|
|
#define LCD_LANGUAGE en
|
|
|
|
#define LCD_LANGUAGE en
|
|
|
|
|
|
|
|
|
|
|
|
//
|
|
|
|
/**
|
|
|
|
// LCD Character Set
|
|
|
|
* LCD Character Set
|
|
|
|
//
|
|
|
|
*
|
|
|
|
// Note: This option is NOT applicable to Graphical Displays.
|
|
|
|
* Note: This option is NOT applicable to Graphical Displays.
|
|
|
|
//
|
|
|
|
*
|
|
|
|
// All character-based LCD's provide ASCII plus one of these
|
|
|
|
* All character-based LCDs provide ASCII plus one of these
|
|
|
|
// language extensions:
|
|
|
|
* language extensions:
|
|
|
|
//
|
|
|
|
*
|
|
|
|
// - JAPANESE ... the most common
|
|
|
|
* - JAPANESE ... the most common
|
|
|
|
// - WESTERN ... with more accented characters
|
|
|
|
* - WESTERN ... with more accented characters
|
|
|
|
// - CYRILLIC ... for the Russian language
|
|
|
|
* - CYRILLIC ... for the Russian language
|
|
|
|
//
|
|
|
|
*
|
|
|
|
// To determine the language extension installed on your controller:
|
|
|
|
* To determine the language extension installed on your controller:
|
|
|
|
//
|
|
|
|
*
|
|
|
|
// - Compile and upload with LCD_LANGUAGE set to 'test'
|
|
|
|
* - Compile and upload with LCD_LANGUAGE set to 'test'
|
|
|
|
// - Click the controller to view the LCD menu
|
|
|
|
* - Click the controller to view the LCD menu
|
|
|
|
// - The LCD will display Japanese, Western, or Cyrillic text
|
|
|
|
* - The LCD will display Japanese, Western, or Cyrillic text
|
|
|
|
//
|
|
|
|
*
|
|
|
|
// See https://github.com/MarlinFirmware/Marlin/wiki/LCD-Language
|
|
|
|
* See https: *github.com/MarlinFirmware/Marlin/wiki/LCD-Language
|
|
|
|
//
|
|
|
|
*
|
|
|
|
// :['JAPANESE', 'WESTERN', 'CYRILLIC']
|
|
|
|
* :['JAPANESE', 'WESTERN', 'CYRILLIC']
|
|
|
|
//
|
|
|
|
*/
|
|
|
|
#define DISPLAY_CHARSET_HD44780 JAPANESE // K8200: for Display VM8201 // this is the most common hardware
|
|
|
|
#define DISPLAY_CHARSET_HD44780 JAPANESE // K8200: for Display VM8201 // this is the most common hardware
|
|
|
|
|
|
|
|
|
|
|
|
//
|
|
|
|
/**
|
|
|
|
// LCD TYPE
|
|
|
|
* LCD TYPE
|
|
|
|
//
|
|
|
|
*
|
|
|
|
// You may choose ULTRA_LCD if you have character based LCD with 16x2, 16x4, 20x2,
|
|
|
|
* Enable ULTRA_LCD for a 16x2, 16x4, 20x2, or 20x4 character-based LCD.
|
|
|
|
// 20x4 char/lines or DOGLCD for the full graphics display with 128x64 pixels
|
|
|
|
* Enable DOGLCD for a 128x64 (ST7565R) Full Graphical Display.
|
|
|
|
// (ST7565R family). (This option will be set automatically for certain displays.)
|
|
|
|
* (These options will be enabled automatically for most displays.)
|
|
|
|
//
|
|
|
|
*
|
|
|
|
// IMPORTANT NOTE: The U8glib library is required for Full Graphic Display!
|
|
|
|
* IMPORTANT: The U8glib library is required for Full Graphic Display!
|
|
|
|
// https://github.com/olikraus/U8glib_Arduino
|
|
|
|
* https://github.com/olikraus/U8glib_Arduino
|
|
|
|
//
|
|
|
|
*/
|
|
|
|
//#define ULTRA_LCD // Character based
|
|
|
|
//#define ULTRA_LCD // Character based
|
|
|
|
//#define DOGLCD // Full graphics display
|
|
|
|
//#define DOGLCD // Full graphics display
|
|
|
|
|
|
|
|
|
|
|
|
//
|
|
|
|
/**
|
|
|
|
// SD CARD
|
|
|
|
* SD CARD
|
|
|
|
//
|
|
|
|
*
|
|
|
|
// SD Card support is disabled by default. If your controller has an SD slot,
|
|
|
|
* SD Card support is disabled by default. If your controller has an SD slot,
|
|
|
|
// you must uncomment the following option or it won't work.
|
|
|
|
* you must uncomment the following option or it won't work.
|
|
|
|
//
|
|
|
|
*
|
|
|
|
|
|
|
|
*/
|
|
|
|
#define SDSUPPORT
|
|
|
|
#define SDSUPPORT
|
|
|
|
|
|
|
|
|
|
|
|
//
|
|
|
|
/**
|
|
|
|
// SD CARD: SPI SPEED
|
|
|
|
* SD CARD: SPI SPEED
|
|
|
|
//
|
|
|
|
*
|
|
|
|
// Uncomment ONE of the following items to use a slower SPI transfer
|
|
|
|
* Enable one of the following items for a slower SPI transfer speed.
|
|
|
|
// speed. This is usually required if you're getting volume init errors.
|
|
|
|
* This may be required to resolve "volume init" errors.
|
|
|
|
//
|
|
|
|
*/
|
|
|
|
//#define SPI_SPEED SPI_HALF_SPEED
|
|
|
|
//#define SPI_SPEED SPI_HALF_SPEED
|
|
|
|
//#define SPI_SPEED SPI_QUARTER_SPEED
|
|
|
|
//#define SPI_SPEED SPI_QUARTER_SPEED
|
|
|
|
//#define SPI_SPEED SPI_EIGHTH_SPEED
|
|
|
|
//#define SPI_SPEED SPI_EIGHTH_SPEED
|
|
|
|
|
|
|
|
|
|
|
|
//
|
|
|
|
/**
|
|
|
|
// SD CARD: ENABLE CRC
|
|
|
|
* SD CARD: ENABLE CRC
|
|
|
|
//
|
|
|
|
*
|
|
|
|
// Use CRC checks and retries on the SD communication.
|
|
|
|
* Use CRC checks and retries on the SD communication.
|
|
|
|
//
|
|
|
|
*/
|
|
|
|
#define SD_CHECK_AND_RETRY
|
|
|
|
#define SD_CHECK_AND_RETRY
|
|
|
|
|
|
|
|
|
|
|
|
//
|
|
|
|
//
|
|
|
|
@ -1238,7 +1235,7 @@
|
|
|
|
*/
|
|
|
|
*/
|
|
|
|
|
|
|
|
|
|
|
|
//
|
|
|
|
//
|
|
|
|
// This option reverses the encoder direction everywhere
|
|
|
|
// This option reverses the encoder direction everywhere.
|
|
|
|
//
|
|
|
|
//
|
|
|
|
// Set this option if CLOCKWISE causes values to DECREASE
|
|
|
|
// Set this option if CLOCKWISE causes values to DECREASE
|
|
|
|
//
|
|
|
|
//
|
|
|
|
|
Scott Lahteine
8 years ago