03fa9fae9f
Merge branch 'Development' into fix_temperature_minmax
...
Latest upstream commits
11 years ago
2606da9e81
Merge pull request #1678 from Nutz95/Development
...
Report changes from previous PR (#1670 ) from old code base including :
11 years ago
1fac388664
Revert measurement loop
11 years ago
37cde8a191
Report changes from previous PR from old code base including :
...
I've updated the minimum values from the LCD.
It has been a while that i want to at least fix this.
I have an inductive probe and often i need to set my zOffset to something lower than 0.5.
With the current implementation, the default LCD value is set to 0.5 for some reason.
On my case i need to be able to set it down to 0.0 as my inductive probe can be lower than 0.5.
Before with the LCD we couldn't change this value below 0.5. We had to flash the firmware every time which was painful.
Now we are able to change this value down to 0.0 if needed.
I've also changed the minimum value for Z min acceleration.
In the default configuration it's set to 25 but on the LCD the minimum was 100 which is not coherent.
I've changes the minimum to 10. On this axis, depending on the mechanics/motor drivers we might require very low acceleration, so i guess 10 is somehow realistic.
11 years ago
b26a3ea02c
Merge pull request #1662 from josla972/refactor_scara
...
Refactor SCARA calibration. Save some lines of code and possibly ROM.
11 years ago
36474be8eb
Merge pull request #1675 from Wurstnase/Development
...
fix bad insertion config again
11 years ago
e6f6c6e3a1
fix bad insertion config again
11 years ago
6bdee87be3
Cleanup temperature code
...
- Get rid of unused temp states in the ISR, resulting in more frequent
temperature reading with fewer sensors
- Shrink code slightly in min/max testing
11 years ago
f65f61fa72
Merge pull request #1672 from thinkyhead/fix_probeaction
...
Fix mangled probe_pt calls
11 years ago
7717e1ce33
Fix bad insert in configuration
11 years ago
146501215f
Fix mangled probe_pt calls
...
- Address issue #1669
- Remove the TOPO_ORIGIN configuration setting
11 years ago
e0a42d3f9a
Merge pull request #1666 from maverikou/fix_1507
...
Fix 1507
11 years ago
15345cc249
Corrected Z_PROBE_ALLEN_KEY behaviour.
11 years ago
0f034dd97e
Clean up Z_RAISE_AFTER_PROBING to work the same in all code paths except Z_PROBE_SLED.
11 years ago
6c96f32069
Blind fix for #1507
11 years ago
379348487e
Removed malplaced comment.
11 years ago
8bd6e37b21
Merge pull request #1661 from thinkyhead/G92_no_offset
...
Don't add home offsets in G29
11 years ago
88ed5268d2
Merge pull request #1663 from thinkyhead/fix_dual_z_1659
...
Fix compile error with `*_DUAL_STEPPER_DRIVERS`
11 years ago
582cd780cd
Fix compile error with `*_DUAL_STEPPER_DRIVERS`
...
- Patch up macros in stepper.cpp
11 years ago
9b3462f73f
Refactor SCARA calibration. Save some lines of code and possibly ROM.
11 years ago
691e753cc3
Don't add home offsets in G29
...
- Address #1262 by leaving values as set
- Rename `add_homing` to `home_offset`
11 years ago
9b639b4135
Merge pull request #1619 from epatel/manual-bed-leveling+mesh-bed-level
...
Manual bed leveling + mesh bed leveling
11 years ago
a96bfee76a
Merge pull request #1660 from thinkyhead/fix_temperature_minmax
...
Fix temperature min/max test
11 years ago
3703694e30
Fix temperature min/max test
...
- Base tests on all thermistors/thermocouples, not just heater 0
11 years ago
3d0a060a7a
Added G29 command
11 years ago
c516747847
Merge branch 'Development' into manual-bed-leveling+mesh-bed-level
11 years ago
b5970492e2
Merge pull request #1656 from AnHardt/menufix
...
Fix for menus failing to scroll
11 years ago
64e3d33893
Fix shrinked menucode
...
by updating 'encoderPosition' in END_MENU() line 1.
11 years ago
a7e89d4cfa
Merge branch 'Development' into manual-bed-leveling+mesh-bed-level
11 years ago
0d869703ca
Merge pull request #1655 from thinkyhead/fix_count_direction_init
...
Fix count_direction initializer
11 years ago
2176a22d42
Fix count_direction initializer
...
- Addressing #1625
11 years ago
e3f04c876a
Merge pull request #1653 from thinkyhead/lcd_menu_hilite
...
Fix hiliting of edit items in LCD menus
11 years ago
5644ad6809
Fix hiliting of edit items
11 years ago
526a755a66
Merge pull request #1652 from AnHardt/PIDdebug
...
PID debug
11 years ago
5112cf8422
Added comment for the EEPROM storage
11 years ago
4619d80524
Merge branch 'Development' into manual-bed-leveling+mesh-bed-level
11 years ago
199151a4ed
Merge pull request #1650 from AnHardt/beautify
...
Beautivy statusscreen
11 years ago
2424713a8f
Merge pull request #1640 from AnHardt/warning6
...
codepos not used in gcode_M28()
11 years ago
e85061d20d
Added changes to the 'new' Configuration.h s
11 years ago
a61f679568
Merge branch 'Development' into manual-bed-leveling+mesh-bed-level
11 years ago
c87faa69ed
Shortened mesh_plan_buffer_line()
11 years ago
47c1ea72af
Merge https://github.com/kieranc/Marlin into PIDdebug
...
Conflicts:
Marlin/temperature.cpp
Cleaned merge conflict.
Codeposition had changed.
Variable pid_input had vanished.
Signed-off-by: AnHardt <github@kitelab.de>
11 years ago
f1d3d1524d
Merge branch 'optimize_menu_code' of https://github.com/thinkyhead/Marlin into beautify
...
Conflicts:
Marlin/dogm_lcd_implementation.h
solved merge conflict.
11 years ago
0858fba192
Merge pull request #1620 from thinkyhead/optimize_menu_code
...
Reduce size of menu code
11 years ago
fa889cd6e1
Beautivy statusscreen
...
by shifting things some pixels around
11 years ago
7279e4f82f
Small code tweaks re lcd.print
11 years ago
90ba61b9b8
Include indicator for new drawmenu_generic
...
In the new method we pass the character that should be used for
selected state, not the character to print always.
11 years ago
15d29efad5
Pass sel to lcd_implementation_mark_as_selected
...
- Pass selected state directly to lcd_implementation_mark_as_selected
- Rename sel function parameter
- Include a minor fix for SdBaseFile.h
11 years ago
a547dc2148
Merge branch 'Development' into optimize_menu_code
...
Get upstream changes
11 years ago
e650d4044e
Fix "Stop Print" function in the LCD menu
...
When one hit "Stop Print" option in LCD menu, the command buffer was not
cleared. The printer keep moving until the buffer has been emptied.
Actually I could not clear the command buffer as well.. I don't know
why, it doesnt work as expected.
I need to implement a routine inside Stepper ISR to handle such
situation.
11 years ago
Scott Lahteine