181cdb3cfe
Move GCode list above include lines
8 years ago
eb120e518c
Followup to new endstop interrupts feature
...
- Fix typos, verbiage
- Fix naming of `setup_endstop_interrupts`
- Some formatting, indentation, spacing
8 years ago
832fe284b4
Merge pull request #5184 from AnHardt/endstop_interrupts
...
Introduce endstop interrupts
8 years ago
d08867986e
Add autotemp capabilities to M104
...
This allows M104 to pass the F and B parameters to enable autotemp as well
8 years ago
2330619da0
Merge pull request #5191 from petrzjunior/const
...
Replace const bool with #define for consistency
8 years ago
d7ce5d271b
Replace const bool with #define for consistency
8 years ago
5d23e52d75
Merge pull request #5228 from thinkyhead/rc_keep_last_mix
...
Fix DIRECT_MIXING_IN_G1 to preserve the previous mix
8 years ago
99b0c1fe56
Fix DIRECT_MIXING_IN_G1 to preserve the previous mix
8 years ago
410657b050
Fix G30 with limits, print correct probe XY
8 years ago
f3eee02596
Introduce endstop interrupts
...
If ENDSTOP_INTERRUPTS_FEATURE is enabled this tries to set up interrupt routines
for all used endstop pins. If this worked without errors, `endstops.update()` is called
only if one of the endstops changed its state.
The new interrupt routines do not really check the endstops and react upon them. All what they
do, is to set a flag if it makes sense to call the endstop test we are used to.
This can be used on:
* ARM (DUE) based boards - all pins can raise interrupts,
* RAMPS - all 6 endstop pins plus some other on EXT-2 can raise interrupts,
* RAMPS based boards - as long the designers did not change the pins for the endstops or at least left enough,
* all boards, if there are enough pins that can raise interrupts, and you are willing/able to swap with pins dedicated to other purpose.
8 years ago
665b7f3893
Merge pull request #5212 from thinkyhead/rc_mixing_faster
...
Store mix factors as reciprocals and multiply
8 years ago
60cc9342a4
Merge pull request #5188 from thinkyhead/rc_extended_host_support
...
Extended host support: M155 Auto temp report, M115 capabilities
8 years ago
f663220e87
Store Mix factors as reciprocals and multiply
8 years ago
b31a07e261
Stateful M355 with separate P parameter
8 years ago
3c9a838651
Extended capabilities report in M115
8 years ago
68b866b5dd
Add M155 - Auto-report temperature with interval
8 years ago
75bfde9945
M155=>M260, M156=>M261
8 years ago
dcfd7c69e8
Merge pull request #5163 from nzinov/RCBugFix
...
Improve G30 probing command - add optional arguments
8 years ago
e765eebfb0
Patch spacing in bilinear grid report
8 years ago
dea00bbcf1
improve G30 probing
...
Add optional parameters
X, Y for probe point
S sets stowing on and off
8 years ago
176aeafc19
Don't define bilinear_line_to_destination on kinematic setups
8 years ago
236853df22
Corrections to bilinear_line_to_destination
...
- Allow more than 9x9 probe points
- Account for the probe starting position
8 years ago
0115e495fe
Fix up Dual X switch blocks
8 years ago
2495ab7af2
Make dual_x_carriage_mode an enumeration
8 years ago
d6c36f5bb9
Fix Z raise with DXC_AUTO_PARK_MODE
8 years ago
0c79553fc5
Cast int to AxisEnum for some accessors
8 years ago
adbf1f7dca
Add M355 to the GCodes list.
8 years ago
63efc10599
Merge pull request #5134 from thinkyhead/rc_bilinear_split_lines
...
Split cartesian moves on grid boundaries with bilinear ABL
8 years ago
ee5b8d6dc8
Split moves on grid boundaries with bilinear ABL on cartesian
8 years ago
66744a6076
Merge pull request #5133 from thinkyhead/rc_M355_case_light
...
M355 Case light
8 years ago
955d14acb0
Patch photo pin code style
8 years ago
ab3f966f5f
Case light G-code M355
...
implemented G-Code M355 into Marlin
8 years ago
f9bea7968f
BugFix for incorrect E-speed calculation
...
The extrusion speed was wrong due to a not high enough precision of
esteps to XY steps, therefore now the target float values are used to
calculate the ratio between XY movement and extrusion speed.
The e_speed_multiplier8 was replaced by an absolute multiplier called
abs_adv_steps_multiplier8, therefore one multiplication and bitshift can
be saved inside the stepper ISR. Due to this, also extruder_advance_k is
better suited inside the planner and not the stepper files any more.
8 years ago
ff3a8ca0d1
Use NUM_DIGITAL_PINS instead of custom DIO_COUNT
8 years ago
04a1fac029
Some cleanup to M43
8 years ago
c7f1f0dae6
Add endstop monitor & make pins report pretty
8 years ago
396434a445
Fix compiler warning in M145
8 years ago
07bfc45df8
Adjust spacing in gcode_M149
8 years ago
1a2310c494
Make LCD preheat vars an array to reduce code size
8 years ago
50ee749082
Centralize click-handling in the LCD loop
8 years ago
47ad97c35e
Merge pull request #5109 from thinkyhead/rc_eeprom_M218_tool_offset
...
Save hotend_offset array (M218) in EEPROM
8 years ago
67ab54185b
Save hotend_offset array (M218) in EEPROM
8 years ago
dfcdbb437b
Fix Command M420
8 years ago
c34dbfb248
Merge pull request #5072 from thinkyhead/rc_preset_auto_fans
...
Add predefined AUTO_FAN_PINs to pins files
8 years ago
c4c53856a4
Merge pull request #5094 from esenapaj/Fix-for-the-PR-#5088
...
Fix for the PR #5088 (Handle M108 in M1 also with ULTIPANEL)
8 years ago
d5a5042d23
Fix for the PR #5088 (Handle M108 in M1 also with ULTIPANEL)
8 years ago
3f94b15cef
Fix bilinear grid constraints
...
Followup to #5090
8 years ago
ada935de87
Allow TEMP_STAT_LEDS with only one LED defined
8 years ago
f0d673561f
Fix for bilinear grid outside bounds
8 years ago
1ba1ec0db9
Handle M108 in M1 also with ULTIPANEL
8 years ago
Scott Lahteine