39cc36d3f1
[1.1.x] M303 thermal runaway protection ( #8209 )
...
* Added M303 thermal runaway protection
Currently, thermal runaway protection is not available during M303.
Therefore, if someone plugs the thermistors in incorrectly and goes to
autotune their printer, the printer temperature could runaway and damage
could occur.
* Replace removed line, clarifying its logic
7 years ago
87d3a1ae4d
Merge pull request #8228 from tcm0116/1.0.x-dual_stepper
...
[1.1.x] Fix automatic stepper assignment for X/Y/Z dual stepper drivers
7 years ago
5289c4135a
Merge pull request #8230 from AnHardt/1.1_watchdog
...
[1.1] Fix watchdog in WATCHDOG_RESET_MANUAL mode AVR
7 years ago
dcd7949544
Fix watchdog in WATCHDOG_RESET_MANUAL mode AVR
7 years ago
277eb16d67
Fix automatic stepper assignment for X/Y/Z dual stepper drivers
7 years ago
41ba4e507e
Merge pull request #8216 from jmdearras/bugfix-1.1.x
...
Restore MKS_GEN_L
7 years ago
c9980c0a5c
Restore MKS_GEN_L
...
Removed by accident, I presume, when the file was cleaned up
7 years ago
3e9504d306
Fix case light "off" function ( #8205 )
...
* Fix case light "off" function
It would only turn the light off if brightness was 255
* Update Marlin_main.cpp
7 years ago
1b68ee82ce
Merge pull request #8196 from thinkyhead/bf1_asterisk_not_special
...
[1.1.x] Allow asterisks in G-Code commands
7 years ago
4bf0e15653
Allow asterisks in G-Code commands
...
Addressing #6655
7 years ago
b63a55666d
Merge pull request #8193 from thinkyhead/bf1_silver_gate
...
[1.1.x] Support for SilverGate Board
7 years ago
f02ca2a9a3
Organize boards.h by architecture
7 years ago
4fb3ce4739
Support for SilverGate Board
7 years ago
b48a77c88a
Merge pull request #8182 from thinkyhead/bf1_fix_bootscreen_repeat
...
[1.1.x] Only show custom bootscreen once
7 years ago
db6de76acb
Only show custom bootscreen once
7 years ago
15be1cb9a9
[1.1.x] Fix NO_MOTION_BEFORE_HOMING unwanted behaviour ( #8177 )
...
* [1.1.x] Fix NO_MOTION_BEFORE_HOMING unwanted behaviour
NO_MOTION_BEFORE_HOMING should prevent XYZ movements only when homing is not done.
E axes should be allowed
* Update Marlin_main.cpp
* Update Marlin_main.cpp
* Update Marlin_main.cpp
7 years ago
4817c0d055
Merge pull request #8167 from thinkyhead/bf1_config_tweak
...
[1.1.x] Kinematic clamp_to_software_endstops
7 years ago
893092ff7f
Kinematic clamp_to_software_endstops
7 years ago
8b7c1e9cec
Fix for MAX_VFAT_ENTRIES sanity check
7 years ago
393ceb28fc
The plural of 'axis' is 'axes'
7 years ago
d9cb7be444
Merge pull request #8160 from thinkyhead/bf1_fixup_sd_reprint
...
[1.1.x] Simplify SD_REPRINT_LAST_SELECTED_FILE
7 years ago
5837f067cf
Tweak to QUICK_HOME comment
7 years ago
5e5a177934
No hacks needed for SD_REPRINT_LAST_SELECTED_FILE
7 years ago
0b5b03d9dc
Tweak for soft endstops
7 years ago
9288d80613
Merge pull request #8156 from thinkyhead/bf1_anet_10_servo
...
[1.1.x] Define a default SERVO0_PIN for Anet 1.0
7 years ago
6698db29de
Update LCD draw condition
7 years ago
25e86a520d
Merge pull request #8114 from thinkyhead/bf1_print_sd_file_again
...
[1.1.x] Cleanup for SD Print Again
7 years ago
a6f7cda23e
Merge pull request #8143 from thinkyhead/bf1_dual_xyz_endstops
...
Followup to #8123 - to match 2.0.x changes
7 years ago
b0e282a74b
Cleanups for SD_REPRINT_LAST_SELECTED_FILE
7 years ago
46ed54cd8e
Include time scale in some planner vars
7 years ago
9c870baf84
Add a hidden 8s watchdog option for easier debugging
7 years ago
21249f7c3d
Add mfup to mfpub for safety
7 years ago
471c2b5d5c
Provide a default SERVO0_PIN for Anet 1.0
7 years ago
e792c2b234
Followup to #8123 - to match 2.0.x changes
7 years ago
daa85f71e1
Merge pull request #8123 from thinkyhead/bf1_dual_xyz_endstops
...
[1.1.x] Dual endstops XYZ
7 years ago
9850ba0cbd
[1.1.x] Fix M303 thermal protection #8103 ( #8126 )
...
* Fixed M303 thermal protection
The temperature sanity checking logic was not being applied during M303
(pid autotuning) because instead of setting a target temperature, it
directly manipulated the pwm values. When PIDTEMP/PIDTEMPBED is
enabled, PWM values rather than the target temperature determine whether
the heater is on. I changed this to look directly at the PWM amount
when pid is enabled.
* Turn off heaters on M303 error
Currently, PID autotuning stops if it overshoots the temperature by 20C
or if if the temperature does not change for 20 minutes and it times
out. I added calls to disable the heaters in these scenarios.
* Removed unnecessary if statement.
Added changes suggested by GMagician.
* Update temperature.cpp
* Update temperature.cpp
* Update temperature.cpp
7 years ago
c0a8275cb0
Merge pull request #8137 from LVD-AC/(1.1.x)bug_G33
...
(1.1.x) serious bug G33
7 years ago
318c419f77
Implement support for Dual X and Y endstops
7 years ago
7e1232269a
Add Dual Steppers / Endstops to configs
7 years ago
62d52d62dc
Cleanup for DIGIPOTS settings
7 years ago
77cf42588f
(1.1.x) serious bug G33
7 years ago
50f6c645de
Add scripts for .travis.yml to append config options
7 years ago
7ade65d44b
Merge pull request #8128 from thinkyhead/bf1_revert_babystep_mult
...
[1.1.x] Revert default BABYSTEP_MULTIPLICATOR to 1
7 years ago
a979c428ee
Revert default BABYSTEP_MULTIPLICATOR to 1
7 years ago
6920769a9a
Added MKS GEN L board ( #8088 )
...
[1.1.x] Add MKS GEN L board
7 years ago
410aa0716d
Concise SD_REPRINT_LAST_SELECTED_FILE description
7 years ago
445a7f65cd
Clean up trailing whitespace
7 years ago
e64cfb13b8
(1.1.x) auto tune calibration parameters ( #8031 )
...
* auto tune calibration parameters
* solve warnings
* Tweaks to formatting
* review Thinkyhead
* Error
7 years ago
e374d87ac4
Merge pull request #8112 from thinkyhead/bf1_fwretract_fix_oct26
...
[1.1.x] Improved Firmware Retraction logic
7 years ago
2296d98845
Tweak neopixel self-test
7 years ago
Rowan Meara