c9e3caf928
Save lots of PROGMEM, ~20b SRAM with DIGIPOT_I2C
8 years ago
4134a6b526
Save 88b PROGMEM, 48 bytes SRAM in settings.reset
8 years ago
36cc03a9b4
Save 224b PROGMEM, 48b SRAM in get_homing_bump_feedrate
8 years ago
2a41f0ff84
Save 28b PROGMEM in ultralcd.cpp (line_to_current)
8 years ago
e6d10f6ddd
Spend 48b PROGMEM to save 16b SRAM
...
...by moving `homing_feedrate_mm_s` to PROGMEM.
8 years ago
97e13a30ba
Save over 100 bytes SRAM in pin_is_protected
8 years ago
45c74406cf
Recover 32 bytes of SRAM in Marlin bootscreen code
8 years ago
e1c5a43247
Cleanup stepper current control config options
8 years ago
efc198f952
Spacing, const, comments
8 years ago
7f0945d2b1
Merge pull request #6978 from thinkyhead/fix_z_endstop_adj
...
Fix z_endstop_adj initializer
8 years ago
4406fba994
Fixes #6975
8 years ago
19b62c14f0
Add a script so Travis can test for intentional failure
8 years ago
d28f5d8a78
Fix: z_endstop_adj is never initialized
8 years ago
5d5ff36446
Fix a compile error with _lcd_set_z_fade_height
8 years ago
8db1197c9b
Enable extended capabilities report by default ( #6969 )
...
Ref #5139
8 years ago
82e662fc69
Remove requirement for LCD when UBL is used. ( #6971 )
...
* Remove requirement for LCD when UBL is used.
* fix previous oversights
* further refinement - error messages for P2 & P4
* require R on G26 when not using LCD; default to all points
8 years ago
2c2b991b59
UBL Manual Build Menu Option ( #6972 )
...
One click option to manually build UBL mesh.
8 years ago
0dd0033b33
Save up to 94 bytes of RAM on 20x4 LCD Display machines ( #6964 )
...
* Save up to 94 bytes of RAM on 20x4 LCD Display machines
Moved the custom screen characters out of RAM into Program Memory. With
SD-Card support and the Progress Bar enabled, this saves 94 bytes of RAM
memory.
This was tested using the example_configurations/FolgerTech-i3-2020
files. So a couple small changes to those files snuck into this Pull
Request.
Probably... We can find similar savings in the Graphics LCD code it we
comb through it. And if so... That is the place we really need to
save RAM memory!
* Tidy up white space and indentation
8 years ago
04b07a6ecc
Unused var in Stepper
8 years ago
eb8af486d2
Ensure safe temperature for M600
8 years ago
bfe7fbe5c0
Maintain message scroll rate
8 years ago
6411d65c48
Fix Morgan SCARA S2 calculation
8 years ago
46752588b9
Merge pull request #6948 from Bob-the-Kuhn/redundant_temperature
...
fix redefinition errors for redundant_temperature
8 years ago
5938dae200
Merge pull request #6950 from MagoKimbra/fix_g29_3_point
...
Fix G29 with 3 point
8 years ago
c5e0f08e35
Merge pull request #6951 from fixoid/patch-4
...
Initializing extruder/nozzle servo when turning on the printer
8 years ago
1e2ccca063
Merge pull request #6952 from thinkyhead/bf_final_fixups_123
...
General cleanup before release
8 years ago
e4937b0285
Cleanup of spacing and formatting
8 years ago
1aab9906e6
Initializing extruder/nozzle servo when when turning on the printer
8 years ago
663ff7f92a
Fix G29 with 3 point
8 years ago
9f295581f0
Ubl delta fixes and improvements ( #6941 )
...
* Change all direct changes of ubl.state.active to
set_bed_leveling_enabled() which handles apply/unapply
leveling to maintain current_position consistency.
Fix invalidation of UBL mesh to invalid unreachable
mesh points as well (delta corners).
Fix UBL_DELTA unapply_leveling logic and when
it gets applied, including fade_height changes.
Add optional M114 D for detailed position information,
disabled from compilation by default (M114_DETAIL).
* UBL_DELTA raw and inline kinematics
* UBL planner fall through fix
* consistent variable names
* Cleanup orphaned code and whitespace changes.
Use _O2.
* compile warnings cleanup
* Remove redundant #ifdef condition
8 years ago
c34d7a29a6
fix redefinition errors for redundant_temperature
...
Removing redundant_temperature from public section and leaving it in the
private section
8 years ago
862def2ef4
Merge pull request #6947 from Bob-the-Kuhn/allow-GCODE_DEBUG-when-UBL-enabled
...
Allow DEBUG_GCODE_PARSER when UBL is enabled
8 years ago
6a5d3b580d
fix "hex_address not defined" when UBL is enabled
8 years ago
d336e413aa
Merge pull request #6942 from thinkyhead/bf_cleanups_friday
...
General cleanup after recent commits
8 years ago
789b2928a8
Tweak scrolling message code
8 years ago
fc7d7f87b4
Init probe test pin with FastIO
8 years ago
0282452cea
Make Parser::seen volatile
8 years ago
9a305a467b
Patch LCD Contrast menu item
8 years ago
90ccac4bcf
Clean up after recent commits
8 years ago
fff50d3958
Merge pull request #6940 from Bob-the-Kuhn/Gcode---allow-XY
...
Gcode.cpp - spaces and parameters
8 years ago
2130f10de8
allow space between parameter and value
8 years ago
ebda4663c3
for discusion
8 years ago
e2c3695e11
Merge pull request #6932 from thinkyhead/bf_zrib_2.0
...
Support for ZRIB v2.0 Control Board
8 years ago
911079104e
Support for ZRIB v2.0 Control Board
8 years ago
65a0212866
Easier override of FILWIDTH_PIN
8 years ago
147d9d76fc
Merge pull request #6928 from Bob-the-Kuhn/Fix-case-light-logic-on-Azteeg-X3-boards
...
Fix case light logic on Azteeg_X3 boards.
8 years ago
9118e135f9
Merge pull request #6931 from thinkyhead/bf_malyan_m150
...
Malyan m150 configurations
8 years ago
4288c4fb4f
Configurations for Malyan M150
8 years ago
1919cb0d1e
Config cleanups
8 years ago
e800743268
Merge pull request #6921 from tcm0116/pause_flash
...
Fix issues with advanced pause
8 years ago
Scott Lahteine