42e21bb06e
Add support for Printrboard (from https://github.com/lincomatic/Marlin ) and Brainwave (from https://github.com/metrix/Sprinter ).
12 years ago
57429cb9fe
Fix for keypad
12 years ago
f934d0ef5b
Merge remote-tracking branch 'tonokip/Marlin_v1' into Marlin_v1
...
Conflicts:
Marlin/Configuration.h
12 years ago
ffc69537aa
Update on some comments, make the MOTHERBOARD list complete again.
12 years ago
0f73afb0b0
Avoid defining overriding definitions for the RepRapDiscount Smart
...
Controller. Remove common definitions. Harmonize declaration order.
12 years ago
36b452c7ac
Remove abbrs.
12 years ago
3cbaad9288
RepRapDiscount Smart Controller pin definitions.
12 years ago
f5631a89e8
Add dummy Emergancy Pin to Gen7 1.4
...
Change required after pulling from ErikZalm.
12 years ago
a4f9e1ebf2
Merge git://github.com/ErikZalm/Marlin into Marlin_v1
12 years ago
2873d67b17
Put bogus temp override back in Gen7 up to 1.3
...
Took out the ifdef when I split 1.4 out and forgot to permanently
define it for <=1.3.
12 years ago
d07b6e93d5
Add support for Megatronics
12 years ago
8016f058bc
fix max endstop pins
12 years ago
abf0693e8e
Added KILL_PIN -1 to gen7 boards
12 years ago
d728e35658
Update Marlin/pins.h
12 years ago
1c1fddc7ac
Added support for the Rambo reprap electronics board. Added Mcodes to set
...
motor current and microstepping pins.
12 years ago
47d4f55bc0
Fix Gen7 1.4 pinout
...
Gen7 1.4 uses very different pin assignments, might as well make a new
section and remove some of the conditionals from each. It's easier to change
your pin assingment this way if like me you don't wire it exactly to plan.
12 years ago
50cde90324
Added support for dual Z axis stepper drivers
12 years ago
538189cc19
Fixed soft limits when the origin is in the middle.
...
HOME_POS is now always where the endstop is and can be outside the limits.
The limits are now defined by MIN_POS and MAX_POS rather than HOME_POS and MAX_LENGTH.
The Z is axis now homed first if direction is away from the bed.
Saguinololu limit pins change from MIN to MAX according to the homing direction.
13 years ago
e9bec9b6fe
Fixed E1_ENABLE pin for Ultimaker. This was wrong for the 1.5.4 and 1.5.3 PCB (I cannot check the 1.5.6)
13 years ago
602c8ee02b
Melzi support
13 years ago
464b755918
added support for the UltiController
13 years ago
5550e893d5
New board variant, Open Motion Controller
...
Open Hardware board currently used by the group build of http://tvrrug.org.uk
The board can be found at http://solderpad.com/folknology/open-motion-controller/
Signed-off-by: Michel Pollet <buserror@gmail.com>
13 years ago
2e749d60c3
Added DISABLE_MAX_ENDSTOPS
13 years ago
19a47dae4a
Merge pull request #99 from Justblair/master
...
Better pin configuration for rotary encoder in RAMPS boards
13 years ago
c077316b2b
Added PID autotune. (experimental)
...
M303 Starts autotune. Wait till the Kp Ki and Kd constants are printed.
Put these values in Configuration.h
13 years ago
02ee9e3d30
Changed Pin Assignment for the RAMPS motherboard so that LCD and Rotary encoder are all wired to AUX-4
...
This simplifies wiring for those with RAMPS 1.3 and 1.4 boards.
13 years ago
cb0c84e075
Merge remote-tracking branch 'justblair/master' into Marlin_v1
13 years ago
1d5809d458
Merge pull request #88 from daid/Marlin_v1
...
Made plan_buffer_line arguments const...
13 years ago
ed951b1977
Fixed RAMPS 1.2 support (Found and fixed by rrhb)
13 years ago
f278e1c00f
This is in my opinion a much better way of dealing with SD cards than my previous fix.
...
Instead of adding a momentary switch to fake the insertion of the card I have modified the ultralcd menu item:
Card Menu -> Refresh
to reinitialise the card providing that the SDCARDDETECT pin has been set to -1 in the pins.h file. This requires one less switch on the front panel and the refresh menu item is in the most relevent place for a user who wishes to inert a card and then print from it.
It also means that the "Card inserted" messages do not bother the users of these card readers (they dont make sense for users without SCCARDDETECT)
13 years ago
00d33e6b82
Typo fix
13 years ago
7d124478fa
Only protect the heater pins for the defined extruders.
...
Changed the way the extruder pins are defined so it doesn't create extra -1 entries in the list.
13 years ago
1ebe7d1ab6
Merge pull request #83 from phord/tempfix
...
Add explicit #define for bogus temp override
13 years ago
b65ef8d66c
Add support for upcoming Gen7 v1.4
...
V1.4 moves thermistor power to the always-on 5v line.
The BOGUS_TEMPERATURE_FAILSAFE_OVERRIDE is no longer
needed on this board. Add a new motherboard type to
support this feature.
13 years ago
740f0c7690
Add explicit #define for bogus temp override
...
The code to ignore the "bad thermistor reading failsafe"
suicide function depends on the existing of the PS_ON pin
feature. But in some boards this shouldn't be the case
Fix this by adding an explicit definition to make our
intentions more clear and separable.
13 years ago
ba8500a236
pins.h: Define Z_MAX_PIN for Gen7 board
...
The Z_MAX_PIN value was defined as no-value, but this causes
the compile to fail. Fix this by setting the Z_MAX_PIN to the
correct value (which happens to be 0 for pin PB0/DIO0/0).
13 years ago
7b14953c99
Fix build on Sanguino based boards with ATmega1284P
13 years ago
286d5003fa
Fixed compiler warning for Sanguino compile
13 years ago
ce714fe306
Fixes in pins.h
13 years ago
35e57bf149
Added gen6 deluxe.
13 years ago
84ea2d61e8
Moved gen7 boards to motherboard type 10, 11 and 12.
...
Split ramps1.3 in Sprinter like config and multiextruder config.
13 years ago
d298dd121f
merged SBUBA82 and Justblair
13 years ago
a05a261b72
Added a workaround. Ramps SD card does not have sdcarddetect. My temporary solution is to add a momentary swtich
...
that pulls down the SDCARDDETECT pin and mimicking the pull and reinsert ofa a SD card
13 years ago
1b6765ed12
Updated the pin config for RAMPS 1.3 to include ultimaker new style LCD/Rotary Encoder interface
13 years ago
e661578c84
support for GEN7 1.1,1.2 and 1.3
13 years ago
d309565b56
Merge remote-tracking branch 'upstream/Marlin_v1' into Marlin_v1
...
Conflicts:
Marlin/Configuration.h
13 years ago
11518a987f
merged with triffid fork
13 years ago
da040fd393
Fixed ultimaker heater 1 pins. (Thanks daid)
13 years ago
a11f3b2d2f
- Pins for modified GEN7 assigned
...
- Added support for ATMega1284
13 years ago
9f139d6e0e
Added MAX6675 support. (Thanks to gregfrost)
...
Needs some work to remove the blocking in read max6675.
13 years ago
e45e5c68bb
Added support for Gen3+ (Pins file only)
...
Added late z enable. (blddk request)
Only calculate look ahead if >2 moves in buffer.
Removed some FORCE_INLINE to save memory.
Signed-off-by: Erik van der Zalm <erik@vdzalm.eu>
13 years ago
ab01658fd2
local configuration stuff- WATCHPERIOD causes breakage, disable. few other misc changes
13 years ago
71dc82e0b4
my local configuration
13 years ago
cee5f9020a
added suicide pin for a power supply to the arduino that is only active if the arduino is holding high for an output.
13 years ago
415aadf704
lcd panel bed support
...
advance and ultipanel not any more in default config
13 years ago
e017228569
Merged multiple extruder support.
...
Soft PWM. (Sanguinololu can also have PID temperature control)
Interrupt save WRITE for addresses > 0x0FF
13 years ago
4fd75dc813
Working version of multiple extruders (up to 3)
...
- The temperature control is pretty much complete
(not sure what to do w/ autotemp though)
Changed the pins assignment to clearly separate bed and extruder heaters
and temp sensors, changed a bit how termistor tables are handled.
- The steppers control is rudimentary
(only chanages what pins it uses depending on the active_extruder var,
but that's enough for switching extruder in the start.gcode in the
the profiles)
- Tested only w/ RAMPS 1.4
13 years ago
b0c3871750
more fixing of the sanguino math round problem
13 years ago
7b70caab7c
made progmem mainly, found one bug in cardreader, added a empty class for cardreader in case no sd support.
13 years ago
76b3f805c0
Added teensylu pins
13 years ago
1d171e9e52
reformating and some minor bugs/things found on the way.
13 years ago
40e8081623
changed end of line to windows, which seems to be the majority of developers main platform.
13 years ago
d7c4f0780b
Added M42, M80 and M81
13 years ago
094afe7c10
Merged Marlin, Marlin non gen6 and Ultimaker changes
13 years ago
750f6c33e3
first commit
13 years ago
Johann Rocholl