fa2e3a40e9
fixed LCD manual z axis move Feedrate to 70 (was 1700)
13 years ago
a92b3afe64
added german translation;Menue should be in english.. sounds better
13 years ago
9fa586bbed
fixed languages; Preheat_PLA and Preheat_ABS was not defined for non
...
english
13 years ago
cb02914687
Merge remote-tracking branch 'upstream/Marlin_v1' into Marlin_v1
13 years ago
10bf2bb8e1
-
13 years ago
b4833d55c2
Fixed HOME_POS in combination with G28 X0 or G28 Y0
13 years ago
c6f2ec3c82
remove stop_heating_wait
13 years ago
b48d67ce10
Fixed homing
13 years ago
071eec7aa7
Merge pull request #81 from phord/09469add5560ca8a676c42e4bcd499868c33f0dd
...
Clean up and add some trace info
13 years ago
1ebe7d1ab6
Merge pull request #83 from phord/tempfix
...
Add explicit #define for bogus temp override
13 years ago
de37b2264a
Merge pull request #82 from phord/fix-gen7-build
...
pins.h: Define Z_MAX_PIN for Gen7 board
13 years ago
b65ef8d66c
Add support for upcoming Gen7 v1.4
...
V1.4 moves thermistor power to the always-on 5v line.
The BOGUS_TEMPERATURE_FAILSAFE_OVERRIDE is no longer
needed on this board. Add a new motherboard type to
support this feature.
13 years ago
740f0c7690
Add explicit #define for bogus temp override
...
The code to ignore the "bad thermistor reading failsafe"
suicide function depends on the existing of the PS_ON pin
feature. But in some boards this shouldn't be the case
Fix this by adding an explicit definition to make our
intentions more clear and separable.
13 years ago
ba8500a236
pins.h: Define Z_MAX_PIN for Gen7 board
...
The Z_MAX_PIN value was defined as no-value, but this causes
the compile to fail. Fix this by setting the Z_MAX_PIN to the
correct value (which happens to be 0 for pin PB0/DIO0/0).
13 years ago
09469add55
Add board reset reporting (from Repetier-Firmware)
13 years ago
f3101e96d9
Add suitable .gitignore to avoid build noise
13 years ago
245dca4bee
Makefile: generic pde=>cpp rule
...
This adds flexibility to the makefile by allowing different pde
targets to be specified for different needs.
13 years ago
97d42ca2b2
SDSUPPORT default disabled
13 years ago
2faa0852b9
Merge pull request #79 from changwoo/Marlin_v1
...
Fix build on Sanguino based boards with ATmega1284P
13 years ago
7b14953c99
Fix build on Sanguino based boards with ATmega1284P
13 years ago
286d5003fa
Fixed compiler warning for Sanguino compile
13 years ago
66d50562b6
Merge pull request #76 from iXce/Marlin_v1
...
Fix Makefile
13 years ago
27f595a444
Changed version => RC2
13 years ago
018c567abf
Moved SLOWDOWN function. (jetty840)
...
Included AD595 calibration options. (daid)
13 years ago
4fbda5c3f5
Merge remote-tracking branch 'daid/Marlin_v1' into Test
13 years ago
ce714fe306
Fixes in pins.h
13 years ago
35e57bf149
Added gen6 deluxe.
13 years ago
84ea2d61e8
Moved gen7 boards to motherboard type 10, 11 and 12.
...
Split ramps1.3 in Sprinter like config and multiextruder config.
13 years ago
adc108d79e
Correctly build the produced applet/Marlin.cpp source
13 years ago
5aa9c41ab1
Changed comment mode for detection.
...
Added M221 extuder multiply factor.
13 years ago
00690f7ffd
Fix cast warning in Gen7
13 years ago
01d28c18ab
Fixed casting warning in sanguino
13 years ago
2fd8c248fe
Added Fan control to the pre-heat settings.
...
I find that the PID routine works better when the cooling fan is switched on
at the beginning of a warm up routine. Otherwise when you enable the fan
just before a print, you have a delay as the PIDre-adjusts.
This should also be safer as most cooling fans are directed at the hot -ends
thermal barrier!
13 years ago
d9f2f509d5
Added new menu items under the prepare submenu.
...
Instead of a single pre-heat, now there is pre-heat ABS and PLA options
Added defines to the configuration file to adjust preheat temperatures for both
13 years ago
ae3e7586c6
Added HOME_POS. This adds the posibility to make the center 0
...
Updated the Xsteps ... settings via the LCD menu
13 years ago
df1437bd86
Changed display format for some numbers.
13 years ago
8816ef1c64
Small fixes after merge
13 years ago
d298dd121f
merged SBUBA82 and Justblair
13 years ago
2cc9a89830
Merge remote-tracking branch 'SCUBA82/Marlin_v1' into Marlin_v1
13 years ago
a0a1f81913
various changes
13 years ago
8a8ea50f33
fixed manual axis movement lcd option
13 years ago
b976692d0f
Removed VS project files for tidyness stakes
13 years ago
fe940a142d
Added a structure that will allow easy translations/modifications to the LCD menu.
...
Signed-off-by: Blair Thompson <mail@justblair.co.uk>
13 years ago
b3fb09a20c
change preheat to ABS values of nozzle 227 and be 105 C
...
next try for manual axis movement
13 years ago
6a3f8cf23f
Infos about fuses to use; correct fuses in boards.txt
13 years ago
a05a261b72
Added a workaround. Ramps SD card does not have sdcarddetect. My temporary solution is to add a momentary swtich
...
that pulls down the SDCARDDETECT pin and mimicking the pull and reinsert ofa a SD card
13 years ago
1b6765ed12
Updated the pin config for RAMPS 1.3 to include ultimaker new style LCD/Rotary Encoder interface
13 years ago
1ff99ae25f
ATMega1284P support for Arduino IDE
...
replace $ARDUINO_HOME/hardware/tools/avr/etc/arduino.conf with this file
13 years ago
234fe8ea67
added infos for this fork
13 years ago
e661578c84
support for GEN7 1.1,1.2 and 1.3
13 years ago
Christian Thalhammer