002cd6df49
Added new XCK_RESCUE_CLOCK_ENABLE compile time option to the AVRISP-MKII clone programmer project (thanks to Tom Light).
14 years ago
f2324fc2b4
Second patch to fix incorrect PDI/TPI programming speed.
14 years ago
d41cd9a41a
Fixed PDI/TPI programming speed of ~250KHz in the AVRISP-MKII Clone project, instead of the desired 500KHz.
14 years ago
0ce2950d81
Added board hardware driver support for the Adafruit U4 breakout board.
...
Fixed calculation of timer register reload values derived from F_CPU; must subtract one from the division result for the compare value to be correct.
Change AVRISP-MKII rescue clock speed to 4MHz to ensure that a 125KHz ISP speed works regardless of the target's fuses (i.e. DIV8 set).
14 years ago
5ce8380a7d
Fix XPLAINBridge code broken during the changes to the Rescue Clock generation in the AVRISP-MKII clone project.
...
Change over all low level host mode project's descriptor comparator routines to perform the descriptor casting in a temp variable to make the code clearer and easier to modify (despite being more verbose).
14 years ago
3bf760ad7d
Rescue clock of the AVRISP-MKII moved to the AVR's OCR1A pin, so that the clock can be generated at all times when 125KHz ISP programming mode is selected.
14 years ago
cb779e3d7d
Changed over www.fourwalledcubicle.com links to the new www.lufa-lib.org redirect domain, including the new aliased links for LUFA-related pages such as the various download/source control mirrors and support lists.
14 years ago
5a4def7478
Clean up excessive whitespace at the end of each line using the wspurify tool made by Laszlo Monda
14 years ago
93793679c9
Revert change to the AVRISP-MKII project for fuse byte programming via the CMDEX bit - this appears to be an error in the XMEGA manual external memory programming table.
14 years ago
a447ae134f
Fixed broken lock byte programming in the AVRISP-MKII clone project for some XMEGA targets.
14 years ago
824ce10390
Fixed broken FLASH/EEPROM programming in the AVRISP-MKII clone project when writing in non-paged mode and the polling byte cannot be used.
14 years ago
a509729b2d
Changed default value for the reset polarity parameter in the AVRISP-MKII project so that it defaults to active low drive.
...
Fixed incorrect USB_DeviceState value when unconfiguring the device without an address set.
14 years ago
009eebf229
Fix incorrect ADC driver documentation for the parameters of ADC_Init(), fix incorrect call to ADC_Init() in the TemperatureDatalogger project.
15 years ago
81998ce297
Added compile time error to the AVRISP-MKII project when built for the U4 chips, as the default VTARGET detection ADC channel does not exist on these chips (thanks to Marco).
15 years ago
9274610a48
Commit for the 100807 release.
15 years ago
48c5cdced4
Hide the PROGMEM attribute from Doxygen, as it appears to confuse the parser in some situations.
15 years ago
0f45b9c8e0
More spell checking of all source files -- correct missed errors, switch to EN-GB spelling dictionary.
15 years ago
30c2b620de
Remove obsolete macros and preprocessor checks from the AVRISP-MKII project's V2Protocol command handler header file.
15 years ago
de5b16909a
Added support to the AVRISP-MKII project for ISP speeds slower than 125KHz via a new software SPI driver.
...
Added new SPI_ORDER_* data order masks to the SPI peripheral driver.
15 years ago
2461ae508c
Future proof the XPROG protocol of the AVRISP-MKII project, so that non PDI and TPI requests return failure.
15 years ago
6bda628718
Update all demos, projects and bootloaders to indent all function parameters, one per line, for better readability.
...
Add missing const qualifiers to the demos.
15 years ago
d83cc9ac80
Change AVRISP-MKII and XPLAINBridge descriptors to indicate that the device is bus-powered only. Add compile time options to reduce the compiled size of the firmware.
15 years ago
666c0fa4c3
Remove the timeout period extension code from the AVRISP project, as no single command should ever exceed the maximum timeout period. Extend timeout period to 1 second per command, so that an accidental timeout will never occur.
15 years ago
016a4c068a
Make loops in AVRISP-MKII Clone project's XPROG protocol infinite rather than looping on the timeout value, as this is already checked inside the loop anyway.
15 years ago
51c2dcf3b0
Fixed broken PDI EEPROM Section Erase functionality in the AVRISP-MKII project.
15 years ago
711542ee89
Spell check code and manual pages. Remove custom Doxygen CSS stylesheet, as the new 1.7 Doxygen's default stylesheet is much better.
15 years ago
a14ece5f57
Change over Doxygen \note documentation to \pre where applicable.
15 years ago
fc92f9969c
Minor documentation cleanups.
15 years ago
3b95b8dedc
Added new VTARGET_REF_VOLTS and VTARGET_SCALE_FACTOR compile time defines to the AVRISP-MKII programmer project to set the VTARGET reference voltage and scale factor.
...
Fixed XPLAINBridge project not correctly reading the XMEGA's supply voltage when reporting back to the host.
15 years ago
670413603f
The EEPROM stream read/write functions now use eeprom_update_byte() instead of eeprom_write_byte(), so that only changed bytes are written to EEPROM to preserve its lifespan.
...
Changed over the AVRISP-MKII and TemperatureDataLogger projects to use eeprom_update_byte() when writing non-volatile parameters to EEPROM to preserve its lifespan.
15 years ago
ff61dfa505
Fixed AVRISP project not sending a full erase-and-write EEPROM command to XMEGA targets when writing to the EEPROM instead of the split write-only command (thanks to Tim Margush).
15 years ago
80d85090ba
Fixed AVRISP project sending a LOAD EXTENDED ADDRESS command to 128KB AVRs after programming or reading from the last page of FLASH.
15 years ago
34047efc7e
Remove incorrect check for the current device state in the Set Configuration request handler of DevChapter9, which broke Set Configuration requests to the device under most circumstances.
...
Move out the SPI prescaler list to a PROGMEM module-level variable in ISPTarget.c.
15 years ago
571159df1b
Additional fix to the AVRISP-MKII clone project for 256KB AVRs.
15 years ago
cd0093a14b
Fixed AVRISP-MKII clone project not correctly issuing SET EXTENDED ADDRESS commands when the extended address boundary is crossed during programming or readback (thanks to Gerard Sexton).
...
Fixed warnings when building the AVRISP-MKII clone project with the ENABLE_XPROG_PROTOCOL compile time option disabled.
15 years ago
071e02c6b6
Add svn:eol-style property to source files, so that the line endings are correctly converted to the target system's native end of line style.
15 years ago
ab8668b14e
Removed software PDI/TPI emulation from the AVRISP-MKII clone project, as it was very buggy. PDI and TPI must now be implemented via seperate headers instead of the one unified ISP/TPI/PDI header.
15 years ago
eed7d4df6a
Added new ENDPOINT_*_BusSuspended error code to the Endpoint function, so that the stream functions early-abort if the bus is suspended before or during a transfer.
15 years ago
5c0c0327d5
Increase hardware PDI/TPI programming speed to 1MHz in the AVRISP MKII clone project.
15 years ago
a5e79333e5
Switch back to C based timeout ISR in the AVRISP project - assembly version was failing, and only one or two cycles could be shaved off the compiler generated code.
15 years ago
3d28d53c3e
Change AVRISP project's timeout to be interrupt based again, but make the interrupt itself interruptable and use a seperate assembly file to hand-optimize the ISR code.
...
Removed the cast to uint16_t on the set baud rate in the USBtoSerial project, so that the higher >1M baud rates can be selected (thanks to Steffan).
15 years ago
9a1560dc05
Make sure that long reads are aborted early if the connection times out while waiting on more bytes in the AVRISP MKII clone project.
15 years ago
ceb16ee24f
Make sure that the NVM bus/controller busy waits in the AVRISP MKII clone project abort properly if a timeout occurs while waiting for a response.
15 years ago
85aaaf84ce
Make AVRISP-MKII clone project's software PDI/TPI mode more robust by keeping track of timeouts while waiting for a Tx/Rx to finish.
15 years ago
5993e1efe7
Added ability to search by Channel PSM to the GetChannelData() function in the BluetoothHost demo.
...
Added new HCI states to properly initialize the bluetooth dongle and retrieve the local BDADDR.
Factored out Bluetooth state information into a new state structure for easy reference in the user application.
Added new StackInitialized() Bluetooth stack callback function.
15 years ago
fa1a092901
Add user callback function to the Bluetooth host demo to filter out connections from remote devices. Add in ability to reject connections based on their bluetooth device address.
...
Clean up RelayBoard project code.
Make AVRISP project clear the XMEGA target's reset register twice; this does not appear to take affect properly the first time under some circumstances.
15 years ago
c9148f9b47
Added WIN_LIBUSB_COMPAT compile time option to the AVRISP programmer project to make the code compatible with Windows builds of avrdude at the expense of AVRStudio compatibility.
15 years ago
72527867f6
Remove redundant check in the software PDI programming code of the AVRISP project.
15 years ago
9a5ae36a4f
Software PDI mode breaks unless the software USART has 100 cycles between bits.
15 years ago
2b74b517ea
Don't enable the pullup on the target /RESET line in the AVRISP project for PDI mode - clearing the XMEGA's reset control register twice is enough to release it from reset. Possible silicon bug, since the official Atmel programmers have the same issue.
15 years ago
Dean Camera