57fe6b4fb9
Don't cast the line encoding baud rate to a uint16_t before performing the baud rate calculation in the Benito project.
16 years ago
27eb17cb93
Change over unix line-endings to dos line endings.
16 years ago
9c8bd6ed9b
Remove incorrect Abstract Call Management class specific descriptor from the CDC demos, bootloaders and projects.
16 years ago
ab8668b14e
Removed software PDI/TPI emulation from the AVRISP-MKII clone project, as it was very buggy. PDI and TPI must now be implemented via seperate headers instead of the one unified ISP/TPI/PDI header.
16 years ago
27f0ba6fc3
Fixed device state not being reset back to the default state if the host sets the address to 0x00.
...
Fixed Set Configuration requests not being stalled until the host has set the device's address.
Fixed possibility of internal signature retrieval being corrupted if an interrupt occurs during a signature byte read (thanks to Andrei Krainev).
16 years ago
eed7d4df6a
Added new ENDPOINT_*_BusSuspended error code to the Endpoint function, so that the stream functions early-abort if the bus is suspended before or during a transfer.
16 years ago
5c0c0327d5
Increase hardware PDI/TPI programming speed to 1MHz in the AVRISP MKII clone project.
16 years ago
a5e79333e5
Switch back to C based timeout ISR in the AVRISP project - assembly version was failing, and only one or two cycles could be shaved off the compiler generated code.
16 years ago
3d28d53c3e
Change AVRISP project's timeout to be interrupt based again, but make the interrupt itself interruptable and use a seperate assembly file to hand-optimize the ISR code.
...
Removed the cast to uint16_t on the set baud rate in the USBtoSerial project, so that the higher >1M baud rates can be selected (thanks to Steffan).
16 years ago
9a1560dc05
Make sure that long reads are aborted early if the connection times out while waiting on more bytes in the AVRISP MKII clone project.
16 years ago
ceb16ee24f
Make sure that the NVM bus/controller busy waits in the AVRISP MKII clone project abort properly if a timeout occurs while waiting for a response.
16 years ago
e977774d4e
Relocate USBInterrupt.c/.h from the HighLevel USB driver directory to the LowLevel directory as it is hardware-dependent.
16 years ago
59c4871f80
USB_Init() no longer calls sei() to enable global interrupts - this must now be done in the user application once all init code has run.
16 years ago
85aaaf84ce
Make AVRISP-MKII clone project's software PDI/TPI mode more robust by keeping track of timeouts while waiting for a Tx/Rx to finish.
16 years ago
5993e1efe7
Added ability to search by Channel PSM to the GetChannelData() function in the BluetoothHost demo.
...
Added new HCI states to properly initialize the bluetooth dongle and retrieve the local BDADDR.
Factored out Bluetooth state information into a new state structure for easy reference in the user application.
Added new StackInitialized() Bluetooth stack callback function.
16 years ago
fc8e4837a9
Add const keyword to the demo function parameters where possible.
16 years ago
5e14c194c9
Fixed Set/Clear Feature requests directed to a non-configured endpoint not returning a stall to the host.
...
Make TeensyHID bootloader use an 8 byte control endpoint to match the official Teensy, just in case Paul decides to authenticate on that attribute in the future.
16 years ago
e55f338663
Document the Bluetooth ACL layer. Remove unneeded parameters from the signalling command processing routines.
...
Change over the code so that the bluetooth packet data is read in by the stack rather than the user application, to make it more unform for sending/receiving, and so the library can handle incomming fragmentation in the future.
Start Service Discovery Protocol decoding and processing.
16 years ago
ee74b4948f
Add information request/response signal handler to the Bluetooth Host demo.
...
Ensure that the AVRISP-MKII project's Windows avrdude compatibility define is named properly in all parts of the code.
16 years ago
fa1a092901
Add user callback function to the Bluetooth host demo to filter out connections from remote devices. Add in ability to reject connections based on their bluetooth device address.
...
Clean up RelayBoard project code.
Make AVRISP project clear the XMEGA target's reset register twice; this does not appear to take affect properly the first time under some circumstances.
16 years ago
fd96b28882
More improvements to the incomplete BluetoothHost demo - add Disconnection Event processing.
...
Remove unused macro in the host mode demos for the maximum Configuration Descriptor size.
16 years ago
c9148f9b47
Added WIN_LIBUSB_COMPAT compile time option to the AVRISP programmer project to make the code compatible with Windows builds of avrdude at the expense of AVRStudio compatibility.
16 years ago
ce46257ff2
Add RelayBoard project patch from OBinou.
16 years ago
3790907f4d
Added board hardware driver support for the Benito programmer.
16 years ago
9257f4ab8e
Add briefs for the library core structures.
16 years ago
74353374c3
All Class Driver Host mode demos now correctly set the board LEDs to READY once the enumeration process has completed.
...
Fixed Still Image Host class driver not resetting the transaction ID when a new session is opened, fixed driver not sending a valid session ID to the device.
16 years ago
b8db5fc1e7
Added new Relay Controller Board project (thanks to OBinou).
...
Added hardware board driver support for the PJRC Teensy line of USB AVR boards.
16 years ago
f79f9abd28
Fixed compilation error in the AudioInput demos when MICROPHONE_BIASED_TO_HALF_RAIL is defined (thanks to C. Scott Ananian).
...
Minor documentation cleanups.
Make sure HID class driver uses properly cast pointers when writing to the report buffer.
16 years ago
4e99625f7c
Change over MIDIToneGenerator to use only a single channel (MIDI channel 1) due to cycle constraints.
16 years ago
c58c53dba9
Added incomplete MIDIToneGenerator project.
16 years ago
49b09a2042
Standardized the naming scheme given to configuration descriptor sub-elements in the Device mode demos, bootloaders and projects.
...
Fix errors in the MouseHostWithParser demo from incorrect use of the HID_ALIGN_DATA() macro.
16 years ago
5227ca4ce2
Double bank CDC endpoints in the XPLAIN Bridge project, re-enable JTAG once the mode selection pin has been sampled.
16 years ago
72527867f6
Remove redundant check in the software PDI programming code of the AVRISP project.
16 years ago
9a5ae36a4f
Software PDI mode breaks unless the software USART has 100 cycles between bits.
16 years ago
7d51e51c79
Increased throughput of the USBtoSerial demo on systems that send multiple bytes per packet (thanks to Opendous Inc.).
16 years ago
2b74b517ea
Don't enable the pullup on the target /RESET line in the AVRISP project for PDI mode - clearing the XMEGA's reset control register twice is enough to release it from reset. Possible silicon bug, since the official Atmel programmers have the same issue.
16 years ago
39d56aeffe
Fixed PDI programming mode in the AVRISP programmer project not exiting programming mode correctly (clear target Reset key twice, set /RESET pin to pullup).
...
Add newlines to the MIDI event printf() statements in the MIDI host demos.
16 years ago
aca7863350
Added ENABLE_TELNET_SERVER compile time option to the Webserver project to disable the TELNET server if desired.
...
Change over static strings in the Webserver project to use PROGMEM where possible.
16 years ago
92418433a5
Fix incorrect LED mask name in the Webserver project.
...
Fix missing text from the Host Mode States enum documentation.
16 years ago
ce260ae786
Webserver project now uses the board LEDs to indicate the current IP configuration state.
...
Don't double-read data from the attached disk in the incomplete StandaloneProgrammer project when in host mode.
16 years ago
c0c982df7a
Added a timeout value to the TWI_StartTransmission() function, within which the addressed device must respond.
...
Fixed TWI_StartTransmission() corrupting the contents of the GPIOR0 register.
16 years ago
071fd8ce53
Revert changes made for the partial port to the AVR32 architecture.
16 years ago
e11fddfe66
Update Temperature board driver to be AVR32 compatible when the ADC peripheral driver is eventually ported. Make architecture includes explicit for both the AVR32 and the AVR8, to make way for future architecture ports.
...
Add SPI driver aliases for the old function names in the AVR8 driver, so that existing code will still compile against the new version.
16 years ago
c24027f3b5
Fixed software PDI/TPI programming mode in the AVRISP project not correctly toggling just the clock pin.
...
Fix broken AVR8 Serial peripheral driver.
16 years ago
d2851b3351
Oops - need to revert changes made to ease testing of the software PDI programming mode.
16 years ago
5e12d436fa
Remove dual ISR for software PDI mode, use a single ISR instead to reduce code complexity.
16 years ago
e322f14620
More fixes to the AVRISP command timeout system so that it should no longer lock up while processing command no matter what the conditions.
16 years ago
12a01ed72d
Increased the speed of both software and hardware TPI/PDI programming modes of the AVRISP project.
16 years ago
10b9394a8b
Oops - missed a few references to the old global TimeoutMSRemaining counter in ISPTarget.c of the AVRISP-MKII clone project.
16 years ago
ce8d0424b1
AVRISP programmer project now has a more robust timeout system, allowing for a doubling of the software USART speed for PDI and TPI programming.
16 years ago
Dean Camera