Emard
|
4c13f262e8
|
connecting FTDI TXD/RXD
|
8 years ago |
|
Emard
|
092e601af1
|
connecting LEDs
|
8 years ago |
|
Emard
|
364957f9e0
|
connecting OLED
|
8 years ago |
|
Emard
|
feb31c8f87
|
moving inner layer routes away from BGA
|
8 years ago |
|
Emard
|
24c52062fa
|
moving routes under BGA out of inner layers
|
8 years ago |
|
Emard
|
6e2e5f8c39
|
moving routing out of inner layers under BGA to allow
larger copper fill zone for power supply
|
8 years ago |
|
davor
|
3a9160cb16
|
scrapping current routing, placing power supply on copper zones under the BGA
|
8 years ago |
|
davor
|
21aa552e1a
|
placing copper fill zones for power supply by the book
similar to TN1074
|
8 years ago |
|
Emard
|
37f7a62a25
|
reducing minimal drill size to 0.2 mm as
recommended in lattice BGA guide.
Seeedstudio meets this capabilities
OSHpark doesn't
|
8 years ago |
|
Emard
|
8061b47da8
|
moving some resistor near flash chip
|
8 years ago |
|
Emard
|
b12f1b64a6
|
routing spi flash lines
|
8 years ago |
|
Emard
|
820f30f598
|
routing JTAG
|
8 years ago |
|
davor
|
3a079bd1d2
|
moving some resistor closer to ftdi
|
8 years ago |
|
davor
|
48f79d581b
|
reordering PCB elements to simplify or shorten routes
|
8 years ago |
|
Emard
|
6e48d42150
|
fully routed GPIO
|
8 years ago |
|
davor
|
dcc2d375ea
|
routing additional pins to J2 GPIO. 2 differential pairs left to route
|
8 years ago |
|
davor
|
9f0d9c46a7
|
routing half of J2 gpio
|
8 years ago |
|
Emard
|
e30bbeea40
|
routing 4 GPIO on J2
|
8 years ago |
|
Emard
|
48dc148919
|
manually routing J1 differential
|
8 years ago |
|
Emard
|
9050eefd6e
|
update fill zone
|
8 years ago |
|
Davor
|
3446afcc08
|
optimizing PCB component placement
and audio bit ordering
|
8 years ago |
|
Davor
|
19b884baef
|
using corrected schem symbol, reordering pins
|
8 years ago |
|
Davor
|
39dce76f0a
|
use new schem symbol
|
8 years ago |
|
Davor
|
2cda80c3a8
|
manually routed few tracks of GPIO
|
8 years ago |
|
Davor
|
8a53acb71a
|
cleaning GPDI routes and moving OLED back in place
|
8 years ago |
|
davor
|
70fb21781b
|
reorder GPDI differential pairs for almost straitforward routing
|
8 years ago |
|
davor
|
a8f1214b27
|
reorder SDRAM to FPGA connection for straightforward routing
|
8 years ago |
|
Davor
|
19c91e5c6b
|
differential pair track thickness and spacing
|
8 years ago |
|
Davor
|
632e5bd443
|
importing netlist with differential pairs named + -
|
8 years ago |
|
Davor
|
ec42a18d26
|
reordering RAM connections to use peripheral pins near SDRAM chip
|
8 years ago |
|
davor
|
53f11a6950
|
reducing track width to 0.19 mm to pass out of 2nd row of BGA
|
8 years ago |
|
Davor
|
961755fc98
|
manual routing BGA power
|
8 years ago |
|
Davor
|
af042dfef0
|
manually routing BGA power
|
8 years ago |
|
davor
|
a1d25d9d24
|
create copper fill layers
|
8 years ago |
|
davor
|
d6fd30e59c
|
jumper to disable wifi module
|
8 years ago |
|
davor
|
dd597e7b49
|
board production rules for oshpart
|
8 years ago |
|
davor
|
1c5b8a64a3
|
use new footprint for crystal oscillator
|
8 years ago |
|
davor
|
508318d712
|
PCB moving 3.5mm DAC resistors below 3.5m jack, side-by-side
|
8 years ago |
|
davor
|
e9825a4105
|
enlarging the board for 7x2.54 mm to fit triple protoboard
moving OLED into the center (but display turned upside down)
moving heavy parts GPDI and 3.5mm jack on top side
better rearranging the buttons
|
8 years ago |
|
davor
|
9570c1137b
|
small edits
|
8 years ago |
|
davor
|
c297a5294f
|
adding 25 MHz oscillator and moving some parts around
|
8 years ago |
|
Davor
|
12e89e677a
|
connecting wifi, usbserial, oled, sd card
|
8 years ago |
|
Davor
|
0ca9b4cb0e
|
notify possible extra width of the board 7x2.54 mm
that would fit into protoboard
|
8 years ago |
|
Davor
|
3e68526ccb
|
it acutally routed but schematic is still incomplete :)
After freeroute overnight run, DRC complained only for
tracks too close to holes or vias and that is easy to
manually fix
|
8 years ago |
|
Davor
|
ad0ae760b5
|
overnight run of freeroute routed much
but couldn't route it all
|
8 years ago |
|
Davor
|
a477fbd050
|
connecting flash config chip
|
8 years ago |
|
davor
|
a8c293805f
|
moving battery down,
partially routed
|
8 years ago |
|
davor
|
dc1ae11172
|
partially routed board using "freeroute" autorouter
|
8 years ago |
|
davor
|
e37f17e390
|
moving PCB components around
|
8 years ago |
|
davor
|
2dedab2d9a
|
moving 8-pin chip away from 3.5mm jack
|
8 years ago |
