7999249a5c
Set TEMP_SENSOR_0 to 1 in CR-10 example config
...
As pointed out in #7692 by @totalitarian
7 years ago
0ec9a7f090
Fix xon_xoff_state initialization
7 years ago
a47c5c093d
Merge pull request #7459 from ejtagle/xon-xoff-sdxfer
...
[1.1.x] XON/XOFF serial handshake (for faster transfers to SD)
7 years ago
5a674a8e10
Merge pull request #7828 from thinkyhead/bf1_dualx_movex
...
[1.1.x] Fix DUAL_X_CARRIAGE manual move
7 years ago
bcb8722513
Fix DUAL_X_CARRIAGE manual move
...
Addressing #7745
7 years ago
4c34b3ad9c
Stop redundant E4_IS_TMC2130 current control
7 years ago
1b8b5c4b06
Make prepare_move_to_destination_dualx a full move function
7 years ago
451c1fb5f9
Merge pull request #1 from thinkyhead/bf1_xon_xoff_for_sd
...
XON/XOFF changes
7 years ago
4e19ff75b6
XON/XOFF corrections, tweaks, formatting, etc.
7 years ago
94caabf89a
Add XON/XOFF options to example configs
7 years ago
f365448338
Merge pull request #7811 from thinkyhead/bf1_fix_resume_print
...
[1.1.x] Fix broken M600 resume_print
7 years ago
3d1536a1b2
Merge pull request #7814 from thinkyhead/bf1_inhibit_option
...
[1.1.x] Option to disallow motion before homing
7 years ago
8ab426c3a4
Updated all examples configurations
...
Forgot to update examples configurations. Done now
7 years ago
33d28c24bf
Implementing [FR] #7548
...
Added new configuration to inhibit XYZ movements when home is not done
7 years ago
ac70048945
Only MarlinConfig.h ahead of feature block
7 years ago
40a4a716e1
Fix filament change bug in resume_print
...
Expected behaviour: while (auto)extruding the new filament, the nozzle should not move. It should move (from filament replacement position to printing position) only after the user has confirmed the successful filament replacement and extrusion.
Actual behaviour: while (auto)extruding the new filament, the nozzle moves from filament replacement position back to printing position.
So the extrusion step is mixed with the movement required to go back to the printing position.
The provided code seems to be working but probably a better fix is required.
7 years ago
802f147686
Remove some excess whitepsace
7 years ago
80a0f935a1
Fix G10-G11 by adding a synchronize
...
Based on #7792 by @tcm0116
7 years ago
de3c9bade6
Merge pull request #7773 from thinkyhead/bf1_lcd_leveling_status
...
[1.1.x] Show leveling status on character LCD
7 years ago
7f8ff0a724
Show leveling status on character LCD
7 years ago
3a8923be74
Merge pull request #7772 from thinkyhead/bf1_user_menu_return
...
[1.1.x] User menu return-to-status option
7 years ago
723a34d9c7
Add confirmation to Init EEPROM command
7 years ago
2efd5b119d
Add USER_SCRIPT_RETURN option
7 years ago
b105e47cb5
Move SERVO0 pin on GT2560 A+ with BLTOUCH enabled
...
Based on #7769
7 years ago
0c2cefed8f
Merge pull request #7766 from thinkyhead/bf1_melzi_fixes
...
Melzi fixes
7 years ago
41dcbe89dd
Fixed ST7920_DELAY typo
...
Fixed typo where ST7920_DELAY_2 was being #defined after a check for #ifndef ST7920_DELAY_3
7 years ago
70a64355f6
Fixed LCD_FOR_MELZI SanityCheck
...
Sanity Check for LCD_FOR_MELZI would fail with "Please select no more than one LCD controller option" any time #define LCD_FOR_MELZI was enabled in Configuration.h, even if there were no other LCD options enabled.
7 years ago
aefd2a5c4b
Merge pull request #7762 from thinkyhead/bf1_g3d_and_babystep
...
[1.1.x] Fix G3D_PANEL encoder steps, babystep label
7 years ago
e37a1ded0d
Increase BABYSTEP_MULTIPLICATOR to 100
...
Ideally, it should be calculated based on Z steps per unit so that each
babystep corresponds to around 0.025mm. Smaller than this is largely
insignificant for typical layer heights.
7 years ago
3e28243076
No need for LCD_PINS_Dn when unused
7 years ago
bbb94b8f68
babystepping tweak
7 years ago
a277b43e30
Fix babystep menu display
7 years ago
8a994fb1b1
Fix encoder pulses for G3D_PANEL
7 years ago
9ee92f1246
Fix ADVANCED_PAUSE_FEATURE in .travis.yml
7 years ago
ac2ac99e15
Fix bad logic in autostart
...
As pointed out by @marcio-ao in #7638
7 years ago
72e9534d11
Merge pull request #7725 from thinkyhead/bf1_creality_fun
...
More featureful CR-10 configurations
7 years ago
c1cc79176c
Full-featured Creality configs
7 years ago
f25dccd6d1
Disable BABYSTEP_XY by default in all configs
7 years ago
cd09a83cfa
Add size note to SDSORT_LIMIT
7 years ago
9bbc2df217
General code cleanup, spacing
7 years ago
74d430cb97
matrix names update ( #7697 )
...
* matrix names update
* symplified names
* new angle normalization
* ABC
* axis
* least squares
* recalc_delta_settings
* endstop_adj
* 0p
* bug
7 years ago
ca13f4c3dd
Merge pull request #7720 from thinkyhead/bf1_caselight_fix
...
Fix caselight compile issues
7 years ago
9d4d53e2fd
Update links to old wiki page
7 years ago
00896f1713
Fix LEVEL_BED_CORNERS (No leveling required)
7 years ago
c3a9e95a5f
Define drawmenu items once, in ultralcd.cpp
7 years ago
0afd25a010
Fix caselight compile issues
7 years ago
5b87843fae
Addressing #7612
...
Replaced extruder with hotend
7 years ago
386b74f8c2
Merge pull request #7593 from marcio-ao/bugfix-1.1.x
...
Added option for graphical overlay for Z-offset (Resubmission of #7350 and #7586 )
7 years ago
2a963fb5d1
UBL LCD Bugfixes ( #7598 )
7 years ago
d69c5317df
Added option for graphical overlay for Z-offset
7 years ago
Scott Lahteine