Davor
|
ec42a18d26
|
reordering RAM connections to use peripheral pins near SDRAM chip
|
7 years ago |
|
davor
|
9570c1137b
|
small edits
|
7 years ago |
|
davor
|
c297a5294f
|
adding 25 MHz oscillator and moving some parts around
|
7 years ago |
|
Davor
|
a477fbd050
|
connecting flash config chip
|
7 years ago |
|
davor
|
dc1ae11172
|
partially routed board using "freeroute" autorouter
|
7 years ago |
|
davor
|
85cb0b3f93
|
Placing 40-pin connectors side-by-side,
changing ft2232 to ft231x
|
7 years ago |
|
davor
|
5d5a4031cc
|
pins VREF named on schematic symbol of fpga
|
7 years ago |
|
davor
|
a60712b2f6
|
place renumbered schematic units of the fpga chip
|
7 years ago |
|
davor
|
e2899667ef
|
place all available banks to gpio page
|
7 years ago |
|
davor
|
4f3fabdb5f
|
oled updated on the schematic and PCB
|
7 years ago |
|
davor
|
6639abded3
|
add 4 mounting holes
|
7 years ago |
|
davor
|
b661cacede
|
Change to 2x20 pin headers, PCB layout currently sub-optimal
|
7 years ago |
|
davor
|
f9ba6fa20b
|
chage ESP8266-12E to ESP32S
approximate (maybe incorrect) connections - need review
(programming esp from fpga, jtag, sd, chip enable)
|
7 years ago |
|
Davor
|
cf01d5cc8d
|
Power: Replace discharge resistor which leaks with
a diode for discharge C at shutdown
HDMI pin 0 is now the shield and connected to GND
|
7 years ago |
|
davor
|
5d4ce79295
|
connecting BANK2 to PMOD connectors
|
7 years ago |
|
davor
|
23c4cde741
|
GPDI I2C 5V level shifter
|
7 years ago |
|
davor
|
7fd0f561fc
|
Add SPI flash chip
|
7 years ago |
|
davor
|
4b5faa4f58
|
eeprom for FT2232
|
7 years ago |
|
Davor
|
6729ad635e
|
updating transistors pin order
|
7 years ago |
|
Davor
|
c17b4cfa73
|
connecting FT2232 with JTAG
|
7 years ago |
|
Davor
|
09c26de536
|
Corrected SDRAM schematic symbol
|
7 years ago |
|
Davor
|
64741b460a
|
add footprint for crystal 32768 Hz
|
7 years ago |
|
Davor
|
8ed3d57c66
|
Add wake on RTC and shutdown network
|
7 years ago |
|
Davor
|
133417070a
|
add RTC to power sheet
Moving wifi to separate sheet
|
7 years ago |
|
Davor
|
24e8015ff0
|
move usb to "usbserial" sheet and add ft2232 footprint
move sdram to "ram" sheet
create "wifi" sheet
|
7 years ago |
|
Davor
|
e6e569601c
|
rearrange power switching block and LEDs 0-7 -> 7-0
|
7 years ago |
|
Davor
|
e9c1620c89
|
Moving LEDs, OLED and buttons to "blinkey" sheet
|
7 years ago |
|
Davor
|
f6e596d4ee
|
add SDRAM chip (probably wrong footprint)
|
7 years ago |
|
Davor
|
400ad8ac44
|
add push buttons
|
7 years ago |
|
Davor
|
59dde3ae13
|
add DC-DC converter to power sheet
|
7 years ago |
|
davor
|
ab09940a1f
|
labeling GPDI pins (General purpose differential interface)
|
7 years ago |
|
davor
|
f6326e22d9
|
changing BANK0 (Unit A) shematic symbol and
adding BANK1 (Unit B)
|
7 years ago |
|
Davor
|
25672b71ff
|
updating pins for BANK1 (still incomplete)
|
7 years ago |
|
Davor
|
fdfb12770c
|
add missing library footprint/usb_otg
|
7 years ago |
|
Marko Zec
|
400daf5642
|
Reduce board size to 92.5 x 49.3 mm, reshuffle components.
|
7 years ago |
|
davor
|
9afb686693
|
using connectors 2x32 for general purpose and 2x15 for 2 PMODs
Board is now a bit smaller
|
7 years ago |
|
Davor
|
c52fe53c1e
|
Departing from RPI-0 size to a 56x106 mm board
|
7 years ago |
|
davor
|
3f8b5009a9
|
Uploading initial kicad project for ULX3S
|
8 years ago |
