davor
|
1ea88bda53
|
Adding pins to schematic symbols for all chips in unit "H" (SERDES)
Non-serdes chips need GND connection on unit "H".
"power" sheet now connects GND's at unit "H".
|
7 years ago |
|
Emard
|
d57b16519c
|
update (I hope) all chip units to 85F
add more GND vias
|
7 years ago |
|
davor
|
fffde2cf88
|
Additional GND for 85F chips
|
7 years ago |
|
davor
|
e4fc99887e
|
moving GND and VCC on schematics symbols to
common locations for planned PCB which
supports upgrade path for example
12F->25F->45F->85F and if possible ECP5U->ECP5UM
|
7 years ago |
|
Emard
|
06a8d751d9
|
Jumpers (default OFF) for 3 switcher voltages
|
7 years ago |
|
davor
|
10df092413
|
using modified ECP5 footprint
|
7 years ago |
|
davor
|
eaf4c2402a
|
Fab layer, moving values to avoid overlap writings
GPDI footprint edited to remove some unneeded lines
Gerbers update
|
7 years ago |
|
davor
|
f120d212d9
|
433 MHz onboard antenna (need to uncover copper infill layers)
|
7 years ago |
|
davor
|
0229a768ad
|
FPGA direct-to-pin Hackish USB transciver 27 ohm + 3.6 V zener
|
7 years ago |
|
davor
|
fdf38ad9a1
|
DIP switch moved to the right, near RAM.
Maybe should be moved more to the right not to overlap with OLED
|
7 years ago |
|
davor
|
ee20b46f6d
|
connecting ADC substrate pad to GND
|
7 years ago |
|
davor
|
2153a220a0
|
schematic symbol for ADC MAX11123
small PCB traces cleanup
ADC chip placed on PCB but connected only to GND
|
7 years ago |
|
Emard
|
18aef04f2c
|
JTAG header
|
8 years ago |
|
davor
|
9d6f8bf493
|
improving SD card power supply and replacing with
suitable schematic symbol for micro SD card (was normal SD card)
|
8 years ago |
|
Davor
|
19b884baef
|
using corrected schem symbol, reordering pins
|
8 years ago |
|
Davor
|
39dce76f0a
|
use new schem symbol
|
8 years ago |
|
davor
|
70fb21781b
|
reorder GPDI differential pairs for almost straitforward routing
|
8 years ago |
|
davor
|
a8f1214b27
|
reorder SDRAM to FPGA connection for straightforward routing
|
8 years ago |
|
Davor
|
632e5bd443
|
importing netlist with differential pairs named + -
|
8 years ago |
|
Davor
|
ec42a18d26
|
reordering RAM connections to use peripheral pins near SDRAM chip
|
8 years ago |
|
davor
|
9570c1137b
|
small edits
|
8 years ago |
|
davor
|
c297a5294f
|
adding 25 MHz oscillator and moving some parts around
|
8 years ago |
|
Davor
|
a477fbd050
|
connecting flash config chip
|
8 years ago |
|
davor
|
dc1ae11172
|
partially routed board using "freeroute" autorouter
|
8 years ago |
|
davor
|
85cb0b3f93
|
Placing 40-pin connectors side-by-side,
changing ft2232 to ft231x
|
8 years ago |
|
davor
|
5d5a4031cc
|
pins VREF named on schematic symbol of fpga
|
8 years ago |
|
davor
|
a60712b2f6
|
place renumbered schematic units of the fpga chip
|
8 years ago |
|
davor
|
e2899667ef
|
place all available banks to gpio page
|
8 years ago |
|
davor
|
4f3fabdb5f
|
oled updated on the schematic and PCB
|
8 years ago |
|
davor
|
6639abded3
|
add 4 mounting holes
|
8 years ago |
|
davor
|
b661cacede
|
Change to 2x20 pin headers, PCB layout currently sub-optimal
|
8 years ago |
|
davor
|
f9ba6fa20b
|
chage ESP8266-12E to ESP32S
approximate (maybe incorrect) connections - need review
(programming esp from fpga, jtag, sd, chip enable)
|
8 years ago |
|
Davor
|
cf01d5cc8d
|
Power: Replace discharge resistor which leaks with
a diode for discharge C at shutdown
HDMI pin 0 is now the shield and connected to GND
|
8 years ago |
|
davor
|
5d4ce79295
|
connecting BANK2 to PMOD connectors
|
8 years ago |
|
davor
|
23c4cde741
|
GPDI I2C 5V level shifter
|
8 years ago |
|
davor
|
7fd0f561fc
|
Add SPI flash chip
|
8 years ago |
|
davor
|
4b5faa4f58
|
eeprom for FT2232
|
8 years ago |
|
Davor
|
6729ad635e
|
updating transistors pin order
|
8 years ago |
|
Davor
|
c17b4cfa73
|
connecting FT2232 with JTAG
|
8 years ago |
|
Davor
|
09c26de536
|
Corrected SDRAM schematic symbol
|
8 years ago |
|
Davor
|
64741b460a
|
add footprint for crystal 32768 Hz
|
8 years ago |
|
Davor
|
8ed3d57c66
|
Add wake on RTC and shutdown network
|
8 years ago |
|
Davor
|
133417070a
|
add RTC to power sheet
Moving wifi to separate sheet
|
8 years ago |
|
Davor
|
24e8015ff0
|
move usb to "usbserial" sheet and add ft2232 footprint
move sdram to "ram" sheet
create "wifi" sheet
|
8 years ago |
|
Davor
|
e6e569601c
|
rearrange power switching block and LEDs 0-7 -> 7-0
|
8 years ago |
|
Davor
|
e9c1620c89
|
Moving LEDs, OLED and buttons to "blinkey" sheet
|
8 years ago |
|
Davor
|
f6e596d4ee
|
add SDRAM chip (probably wrong footprint)
|
8 years ago |
|
Davor
|
400ad8ac44
|
add push buttons
|
8 years ago |
|
Davor
|
59dde3ae13
|
add DC-DC converter to power sheet
|
8 years ago |
|
davor
|
ab09940a1f
|
labeling GPDI pins (General purpose differential interface)
|
8 years ago |
