Emard
|
91ac1cc478
|
D8,D9,D51,D52: SMA package 2A low drop low profile
|
7 years ago |
|
davor
|
fdf38ad9a1
|
DIP switch moved to the right, near RAM.
Maybe should be moved more to the right not to overlap with OLED
|
7 years ago |
|
davor
|
236f63488a
|
DIP SWITCH routed
|
7 years ago |
|
davor
|
32836831ae
|
i2c of RTC connected to GPDI i2c
|
7 years ago |
|
davor
|
2153a220a0
|
schematic symbol for ADC MAX11123
small PCB traces cleanup
ADC chip placed on PCB but connected only to GND
|
7 years ago |
|
Emard
|
be09416928
|
Add 27 ohm resistors in series with FTDI USB and readme update
|
7 years ago |
|
Emard
|
ee7d266543
|
Resistors for LEDs
|
7 years ago |
|
davor
|
b7500cc477
|
increasing thickness of power traces, moving clock
to a bank which is always at 3.3V
|
7 years ago |
|
davor
|
2a60828a99
|
schem. pullup 1.5k for USB 1.1 full speed mode
|
7 years ago |
|
davor
|
dbf4b92a22
|
audio DAC routed
|
7 years ago |
|
davor
|
23b588ff16
|
Routing... 4 routes remaining
|
7 years ago |
|
davor
|
0f9d00f602
|
Buffer capacitor for SDRAM
|
7 years ago |
|
Emard
|
752eddee0e
|
J1 routed using only purple plane, (yellow plane made free)
|
7 years ago |
|
Emard
|
092e601af1
|
connecting LEDs
|
7 years ago |
|
Emard
|
e30bbeea40
|
routing 4 GPIO on J2
|
7 years ago |
|
Emard
|
48dc148919
|
manually routing J1 differential
|
7 years ago |
|
Davor
|
3446afcc08
|
optimizing PCB component placement
and audio bit ordering
|
7 years ago |
|
Davor
|
19b884baef
|
using corrected schem symbol, reordering pins
|
7 years ago |
|
Davor
|
39dce76f0a
|
use new schem symbol
|
7 years ago |
|
Davor
|
2cda80c3a8
|
manually routed few tracks of GPIO
|
7 years ago |
|
davor
|
70fb21781b
|
reorder GPDI differential pairs for almost straitforward routing
|
7 years ago |
|
Davor
|
aef3945a8e
|
differential pin naming for GPDI, USB, GPIO
|
7 years ago |
|
davor
|
c297a5294f
|
adding 25 MHz oscillator and moving some parts around
|
7 years ago |
|
Davor
|
12e89e677a
|
connecting wifi, usbserial, oled, sd card
|
7 years ago |
|
Davor
|
a477fbd050
|
connecting flash config chip
|
7 years ago |
|
davor
|
dc1ae11172
|
partially routed board using "freeroute" autorouter
|
7 years ago |
|
davor
|
85cb0b3f93
|
Placing 40-pin connectors side-by-side,
changing ft2232 to ft231x
|
7 years ago |
|
davor
|
a7de1a4e58
|
power button
|
7 years ago |
|
davor
|
a60712b2f6
|
place renumbered schematic units of the fpga chip
|
7 years ago |
|
davor
|
e2899667ef
|
place all available banks to gpio page
|
7 years ago |
|
davor
|
c3889467a0
|
rename gpio pins same as BGA pin e.g. A9, C11, ...
|
7 years ago |
|
davor
|
4f3fabdb5f
|
oled updated on the schematic and PCB
|
7 years ago |
|
davor
|
6639abded3
|
add 4 mounting holes
|
7 years ago |
|
davor
|
b661cacede
|
Change to 2x20 pin headers, PCB layout currently sub-optimal
|
7 years ago |
|
davor
|
f9ba6fa20b
|
chage ESP8266-12E to ESP32S
approximate (maybe incorrect) connections - need review
(programming esp from fpga, jtag, sd, chip enable)
|
7 years ago |
|
davor
|
a0dae5bb6a
|
another diode to duscharge C14 at shutdown
|
7 years ago |
|
davor
|
5d4ce79295
|
connecting BANK2 to PMOD connectors
|
7 years ago |
|
davor
|
23c4cde741
|
GPDI I2C 5V level shifter
|
7 years ago |
|
davor
|
7fd0f561fc
|
Add SPI flash chip
|
7 years ago |
|
davor
|
aa8fac622b
|
SD card to sperate "sdcard" sheet
small rearranging and comments
|
7 years ago |
|
davor
|
4b5faa4f58
|
eeprom for FT2232
|
7 years ago |
|
Davor
|
ddd08e597e
|
JTAG port to USB sheet
|
7 years ago |
|
Davor
|
17ba085b6f
|
audio jack to "analog" sheet
|
7 years ago |
|
Davor
|
c1205abfb4
|
Add 3V battery CR1225 holder footprint
|
7 years ago |
|
Davor
|
4a87d52a9d
|
allow FTDI to force power up of the board
|
7 years ago |
|
Davor
|
133417070a
|
add RTC to power sheet
Moving wifi to separate sheet
|
7 years ago |
|
Davor
|
24e8015ff0
|
move usb to "usbserial" sheet and add ft2232 footprint
move sdram to "ram" sheet
create "wifi" sheet
|
7 years ago |
|
Davor
|
c95d2d7b18
|
GPDI to separate sheet
|
7 years ago |
|
Davor
|
e9c1620c89
|
Moving LEDs, OLED and buttons to "blinkey" sheet
|
7 years ago |
|
Davor
|
400ad8ac44
|
add push buttons
|
7 years ago |
|
Davor
|
59dde3ae13
|
add DC-DC converter to power sheet
|
7 years ago |
|
Davor
|
905351cdae
|
Power sheet added
OLED header added
Moving components and adjusting
|
7 years ago |
|
davor
|
ab09940a1f
|
labeling GPDI pins (General purpose differential interface)
|
7 years ago |
|
davor
|
aa5d542fd8
|
shrinking the board
|
7 years ago |
|
davor
|
0f20405afd
|
chip name edited on JTAG to be the same as all units
|
7 years ago |
|
davor
|
aa1e65bd71
|
small edits
|
7 years ago |
|
davor
|
1b53425bb2
|
changing chip name and slightly reordering blocks in the schematics
|
7 years ago |
|
davor
|
f6326e22d9
|
changing BANK0 (Unit A) shematic symbol and
adding BANK1 (Unit B)
|
7 years ago |
|
Davor
|
25672b71ff
|
updating pins for BANK1 (still incomplete)
|
7 years ago |
|
Davor
|
fdfb12770c
|
add missing library footprint/usb_otg
|
7 years ago |
|
Marko Zec
|
400daf5642
|
Reduce board size to 92.5 x 49.3 mm, reshuffle components.
|
7 years ago |
|
davor
|
9afb686693
|
using connectors 2x32 for general purpose and 2x15 for 2 PMODs
Board is now a bit smaller
|
7 years ago |
|
Davor
|
c52fe53c1e
|
Departing from RPI-0 size to a 56x106 mm board
|
7 years ago |
|
davor
|
3f8b5009a9
|
Uploading initial kicad project for ULX3S
|
8 years ago |
