ddb386c139
Init DAC_DISABLE_PIN in dac_init
9 years ago
6c60869409
Support DAC_OR_ADDRESS in Printrboard too
9 years ago
593c8bf286
Support for Rigidbot V2
9 years ago
71a693b3ec
Merge pull request #4154 from thinkyhead/rc_probe_raise_options
...
Use Z_RAISE_BETWEEN_PROBINGS with MBL
9 years ago
829c92f1ba
Use Z_RAISE_BETWEEN_PROBINGS with MBL
9 years ago
eb1755208f
Merge pull request #4153 from thinkyhead/rc_probe_raise_options
...
Combine Z raise before/after options
9 years ago
10da7ac86c
Combine Z raise before/after options
9 years ago
9caa8941e2
Merge pull request #4149 from thinkyhead/rc_minimum_raise_in_probe_pt
...
Ensure a minimum height before XY move in probe_pt
9 years ago
3fa631130f
Ensure a minimum height before XY move in probe_pt
9 years ago
815000ff32
Merge pull request #4148 from thinkyhead/3drag_delay_anhardt
...
Fix up delays in ST7920_SWSPI_SND_8BIT
9 years ago
a7684eef7a
Squish code in ST7920
9 years ago
b4076883cc
Set testet delays for K8200, RAMBO, MINIRAMBO and ST7920
9 years ago
4454d80276
Decrease the needed nops to 1
...
by shitfing the left shift into the high phase.
```
2 cbi 0x2,1 ;set CLK //
1 in r18,__SREG__ //1
1-3 sbrc r24,7 //2-4
2 rjmp .L19 //4
1 cli .L19: //5
2 lds r25,258 lds r25,258 //7
1 andi r25,lo8(-2) ori r25,lo8(1) //8
2 sts 258,r25 sts 258,r25 //10
1 out __SREG__,r18 out __SREG__,r18 //11
2 .L3: rjmp .L3 //13 //2
2 sbi 0x2,1 ;reset CLK // //13-15 //2-4
1 lsl r24 ; val //1
1 nop //2
2 cbi 0x2,1 ;set CLK //4
...
```
9 years ago
56c42b572c
3 ms speedup for ST7920 and delay for BOARD_3DRAG
...
and saving ~1k memory
by limiting the `#pragma GCC optimize (3)` optimisation to `ultralcd_st7920_u8glib_rrd.h`. These optimisation was and is not done for all the other displays, is the reason for the big additionally use of memory, because the complete 'ultralcd.cpp' and 'dogm_lcd_implementation.h' was optimised (sadly i did not observe a change in speed).
Unrolling the loop in `ST7920_SWSPI_SND_8BIT()`, what i expected the optimiser to do, by hand, saved some speed by eliminating the loop variable (i) compares and increases. Every CPU cycle in this loop costs at least 0.5ms per display update because it's executed more than 1k times/s.
The delays are now pre-filled with the calculated values for 4.5V driven ST7920.
A way to simply add __your__ timing into the configuration was made.
At 4.5V
1.) The CLK signal needs to be at least 200ns high and 200ns low.
2.) The DAT pin needs to be set at least 40ns before CLK goes high and must stay at this value until 40ns after CLK went high.
A nop takes one processor cycle.
For 16MHz one nop lasts 62.5ns.
For 20MHz one not lasts 50ns.
To fulfill condition 1.) we need 200/62.5 = 3.2 => 4 cycles (200/50 = 4 => 4). For the low phase, setting the pin takes much longer. For the high phase we (theoretically) have to throw in 2 nops, because changing the CLK takes only 2 cycles.
Condition 2.) is always fulfilled because the processor needs two cycles (100 - 125ns) for switching the CLK pin.
Needs tests and feedback.
Especially i cant test 20MHz, 3DRAG and displays supplied wit less than 5V.
Are the delays right? Please experiment with longer or shorter delays. And give feedback.
Already tested are 5 displays with 4.9V - 5.1V at 16MHz where no delays are needed.
9 years ago
ca184d3d72
Merge pull request #4147 from thinkyhead/rc_fix_M48_raise
...
Fix debug output in probe_pt
9 years ago
e72bd68eaf
Merge pull request #4146 from epatel/epatel/max_z_endstop
...
MBL: Add support for max z endstop
9 years ago
b4161cbd98
Fix debug output in probe_pt
9 years ago
da88b00585
MBL: Add support for max z endstop
...
See https://github.com/MarlinFirmware/Marlin/issues/4088
9 years ago
c8a9829387
Merge pull request #4140 from thinkyhead/rc_button_reliability
...
Always do a brief delay in `lcd_quick_feedback`
9 years ago
74878d1f16
Always do a brief delay in `lcd_quick_feedback`
9 years ago
7de7552069
Merge pull request #4133 from MagoKimbra/Single_home_axis_delta
...
Single home Axis Delta need simple sync_plan_position
9 years ago
de0e6d5f13
Merge pull request #4134 from thinkyhead/rc_followup_4021
...
Additional cleanup to probing/leveling
9 years ago
15a6b49f37
Simplified probe_pt (in G30)
9 years ago
6a7045b9bf
Remove clean_up_after_endstop_move
9 years ago
2a4f866561
Simplified probe_pt (in G29)
9 years ago
89a2aa026b
Simplified probe_pt (in M48)
9 years ago
f8530c5d1f
Simplified probe_pt function (G28 grid)
9 years ago
c376c08042
Simplified probe_pt function (part 1)
9 years ago
9a71b7f8ad
Fix debug message for 3-point leveling
9 years ago
550c03a5a9
Drop raise_z_after_probing function
9 years ago
bb38c816af
Always raise in deploy_z_probe / stow_z_probe
9 years ago
68f3350050
Cleanup M401 / M402
9 years ago
3afda99adf
Regular handlers for G31 / G32
9 years ago
6803c8e37e
Move Z up before, or down after XY, for "blocking move"
9 years ago
03c70c1990
SERVO_DEACTIVATION_DELAY => SERVO_DELAY
9 years ago
570f3bbc07
Single home Axis Delta need simple sync_plan_position
9 years ago
61f34eec03
Merge pull request #4125 from jbrazio/bugfix/planner-warning
...
Fixes some compiler warnings
9 years ago
bdcd628896
Merge pull request #4126 from thinkyhead/rc_lin_timing_patch
...
Patch LIN_ADVANCE timing issue
9 years ago
664232140d
Fixes somes compiler warnings
9 years ago
6e5e388861
Merge pull request #4021 from thinkyhead/rc_raise_z_for_servos
...
Make probes independent of leveling
9 years ago
0c5192b288
Patch LIN_ADVANCE timing issue
...
Also the extruder stepper ISR has to keep an eye on step_loops count.
9 years ago
d4134e6901
Define Z_SAFE_HOMING point when Z_PROBE_SLED is activated alone
9 years ago
7b2fadd598
Apply some fixes from Andreas
...
Derived from
https://github.com/AnHardt/Marlin/commit/6e8ede8c694fa4d9e3c769840b09d56
7f8d8e0dd
9 years ago
bd01592816
Goodbye MECHANICAL_PROBE
9 years ago
2640d13a9f
Simplify initial raise in M48
9 years ago
3763d45656
Return Z position in run_z_probe
9 years ago
1f48b5c30f
Pass a raise to probe_pt, not a Z position
9 years ago
6fdd5ba246
Save and restore feedrate in more places
9 years ago
fe173c2bc6
Generalized probe raise, use for after probing
9 years ago
7da3080761
Simpler cleanup in G28 / G29
9 years ago
Scott Lahteine